• Journal of Biosystems Engineering
• /
• v.32 no.5
• /
• pp.324-331
• /
• 2007

The purpose of this study is to analysis effects of defect factors of combine header for cutting speed of combine header, feeding depth of straw, and cylinder speed of thresher. Measurement system for defect factors was consists of sensors to monitor the combine operation and I/O interface to convert the signals. Cutting speed of combine header, feeding depth of straw, cylinder speed of thresher were measured and analyzed. The data were collected from three paddy field during rice harvesting. The tests were conducted at different grounding speeds, lug troubles, and cutter condition. The one way ANOVA and the multiple comparison tests were performed. The results showed that the measured data were useful to monitor the defect factors of combine during harvesting. The faults conditions of grounding speeds, lug troubles, and cutter conditions affected cutting speeds, feeding depths and cylinder speeds of the combine. The data seem to be useful to analysis the faults conditions of combine header.

• Journal of Biosystems Engineering
• /
• v.26 no.4
• /
• pp.337-354
• /
• 2001

This study was conducted in order to develop a Chinese cabbage harvester attachable to tractors. For designing Chinese cabbage harvester in which laboratory and field tests were conducted with to determine feasible values design factors. To adopt the various sizer of C-cabbages, U-type soft rubber band was attached to the chain conveyor with an angle. Required torque of the conveyor axle was about 206-210kgf$.$cm. And the required peripheral speed of the disk cutter was 6.54m/s or more to have a clean session in root cutting. Three different harvest method were tested. The best harvesting method with minimum pulling force and damage was disk cutting flying just above the soil surface were the cut chinese cabbages are transferring to the holding conveyor attached soft rubber lug in prompt. Theoretical speed ratio of the tractor travel and feed of a chain conveyor was 1:1.2 with the attaching angle of 30 degree and 1:1.1 with the angle of 20 degree. Actual field experiment showed the speed ratio of 1:1.5 was the best because of the slip effect.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.707-712
• /
• 2015

During the welding process, welding distortion is caused by the non-uniformity of the temperature distribution in the weldment. Welding distortion is redistributed because the residual stress and rigidity change according to the removal of the welded structure. In shipbuilding in particular, this phenomenon may be observed during the cutting process of lugs that are attached to blocks for transfer. The redistribution of welding distortion also causes problems, such as damage to the cutting tool. The aim of this study is to experimentally analyze the redistribution of welding distortion because of the partial removal of the welded structure. In the experiments conducted in this study, fillet welding and cutting were performed, and longitudinal bending and angular distortion in the welded structures were then investigated and analyzed.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.117-123
• /
• 2000

Using the modified DEM (Discrete Element Method), which we proposed in order to improve the accuracy of the simulation, soil behavior and reaction by lugs of rotating wheel and a soil cutting process by a high speed blade were calculated and compared with experimental data. The DEM is one of computational mechanics, where the object body is supposed as an assembly of small particles called elements and not a continuum as in the case of FEM. We can easily treat some discrete phenomena such as cracking, separating and sliding by the DEM. We had to modify the original mechanical model, which induced too free movement of elements, adding a tension spring, which would display the role of soil adhesion. The results of DEM simulations were successful from both the soil behavior and reaction points of view.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.81-91
• /
• 2011

This study was conducted to evaluate the necessity of the anchor lug system in continuously reinforced concrete pavement(CRCP) by comparing longitudinal displacements of CRCPs with and without anchor lugs, and to investigate the effect of horizontal cracking on CRCP performance by measuring the vertical displacements. The measurements before and after the anchor lug section was separated were conducted for 12 days in June, and for 14 days in August after the abrupt displacements according to cutting disappeared, respectively. This short term measurement results showed that when anchor lugs were installed, a daily displacement variation at any location was less than 0.1mm; therefore, longitudinal movements were negligibly small. When there were no anchor lugs, longitudinal displacements mainly occurred near the free end and the displacement variation was small; therefore, an expansion joint system seems to be employed at a CRCP terminus without installing anchor lugs. However, further studies are needed to verify the terminus behavior due to annual temperature changes. The horizontal crack width variation was ignorable and did not affect the vertical displacement of the slab. Therefore, the horizontal crack did not delaminate the slab and did not seem to reduce the structural capacity and performance of CRCP.

• Journal of Biosystems Engineering
• /
• v.32 no.3
• /
• pp.153-159
• /
• 2007

This study was conducted to measure and analyze the noise from a combine head. The combine head, comprised of a cutting knife assembly, pick-up chains, horizontally conveying chains and vertically conveying chains, had an overall sound level of 101 dBA. The sound levels of each component were, respectively, 98.3 dBA for the cutting knife assembly, 88.9 dBA for the pick-up chains, 79.8 dBA for the horizontally conveying chains and 86.3 dBA for the vertically conveying chains, being equivalent to 54.4%, 18.4%, 6.5% and 13.7% of the overall head noise. The main cause of the head noise was considered the impacts that the joint of the cutting knife assembly made with frame when it oscillated. The impact sound was also generated when the chain lug collided with the chain case. To reduce these impact sound, anti-vibration rubbers were installed on the knife assembly joint and the chain cases. It reduced the head noise by 4 dBA but the overall noise level of the combine head was still high. In order to protect the combine operators more effectively from the noise, a safety cab needs to be installed on the combine.