• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.245-250
• /
• 2015

This study investigates the lubrication characteristics of fuel injection pumps with reference to different fuel oils. Medium-speed diesel engines use fuel oils with various viscosities, such as heavy fuel oil (HFO, which is a high-viscosity fuel oil) and light diesel oil (LDO, which is a low-viscosity fuel oil). When fuel oil with a low viscosity is used, both fuel oil and lubricating oil lubricate the system. Thus, the lubrication of the fuel injection pump is in a multi-viscosity condition when the fuel oil in use changes. We suggest three cases of multi-viscosity models, and divide the fuel injection pump into three lubrication sections: a, the new oil section; b, the mixed oil section; and c, the used oil section. This study compares the lubrication characteristics with variation of the multi-viscosity model, clearance. The volume of Section b does not affect the lubrication characteristics. The lubrication characteristics of the fuel injection pump are poor when high-viscosity fuel oil transfers to low-viscosity fuel oil. This occurs because the viscosity in the new oil section (i.e., Section a) dominates the lubrication characteristics of the fuel injection pump. However, the lubricant oil supply in the used oil section (i.e., Section c) can improve the lubrication characteristics in this condition. Moreover, the clearances of the stem and head significantly influence the lubrication characteristics when the fuel oil changes.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.248-256
• /
• 1999

Many tribological components in automobile engine undergo high load and sliding speed with thin film thickness. The lubrication characteristics of the components are regarded as ether hydrodynamic lubrication or boundary lubrication, whereas in a working cycle they actually have both characteristics. Many modem engine lubricants have various additives for better performance which make boundary film formation even under hydrodynamic lubrication regime. Conventional Reynolds equation with the viewpoints of continuum mechanics concerns only bulk viscosity of lubricant, which means that its simulation does not give insights on boundary lubrication characteristics. However, many additives of modern engine lubricant provide mixed modes of boundary lubrication characteristics and hydrodynamic lubrication. Especially, high molecular weight polymeric viscosity index improvers form boundary film on the solid surface and cause non-Newtonian fluid effect of shear thinning. This study has performed the investigation about journal bearing system with the mixed concepts of boundary lubrication and hydrodynamic lubrication which happen concurrently in many engine components under the condition of viscosity index improver added.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.189-198
• /
• 2014

This paper presents the results of an experimental investigation of the correlation between the lubrication characteristics of an engine and its fuel economy. Improving the lubrication characteristics of the engine oil is one of the most efficient ways to improve a car's fuel economy. The methods to accomplish this include lowering the viscosity, adding a friction modifier and optimizing the shear stability index of a viscosity index improver. In addition, it is necessary to use different methods to reduce the friction to individual lubrication areas, because different lubrication regimes are used for different engine parts. The experimental investigation in this study is based on design of experiments ; this paper presents the results of a modified Sequence VID test, which is an ASTM standard test used to measure the effects of automotive engine oils on the fuel economy of passenger cars. The results demonstrate the effects of the following lubrication factors on the fuel economy : the low temperature cranking viscosity, high-temperature high shear (HTHS) viscosity, friction modifier, polymer type and shear stability index of the viscosity index improver. Moreover, this study involves an analysis of variance based on design of experiments. The test results show that the HTHS viscosity, friction modifier and shear stability index of the viscosity index improver are more effective than the other factors. Therefore, lowering the viscosity, adding a friction modifier and optimizing the shear stability index of a viscosity index improver should be considered to improve fuel economy.

• 드라이브 ㆍ 컨트롤
• /
• 제18권4호
• /
• pp.84-90
• /
• 2021

Viscosity of hydraulic oils decreases due to loss reduction and efficiency increase of fluid power systems. However, low viscosity is not always appropriate due to the induction of large leakage and small lubricity. Therefore, a detailed study on the optimum viscosity of hydraulic oils is necessary. In this study, based on the thermohydrodynamic lubrication theory, numerical simulation was conducted using the slipper model of swashplate-type axial piston pumps and motors. The viscosity grades' (VG) effects of oils on power losses are mainly discussed numerically in fluid film lubrication, including changes in temperature and viscosity. The simulation results reveal that the flow rate increases and the friction torque decreases as VG decreases. The film temperature and power loss were minimised for a specific oil with a VG. The minimum conditions regarding the temperature and loss were different and closed. Under various operating conditions, the film temperature and power loss were minimised, suggesting that an optimum hydraulic oil with a specific VG could be selected for given operating conditions of pressure and speed. Otherwise, a preferable operating condition must be established to determine a specific VG oil.

• Tribology and Lubricants
• /
• 제7권1호
• /
• pp.55-60
• /
• 1991

The emulsion lubrication is expected to get the effects of cooling and lubrication in metal cutting. The purpose of this research was to investigate the lubrication characteristics of the emulsion in a region of the elastohydrodynamic lubrication by experiments using o/w type emulsion lubrication. With the line contact frictional experiment apparatus which is the model of a rolling mechanism, friction coefficient, and oil film thickness were measured. By analyzing these experimental data with the variables of emulsion concentration, load, and rolling velocity, the following results are obtained. Emulsion viscosity $\eta$ for the concentration and pressure can be calculated by the following equation $\eta=\eta_o e^{\alphap}\cdot e^{\beta \phi}$. Where $\beta = (-3.7242+\phi)/\phi, 5%\leq \phi \leq 15%$.

• Tribology and Lubricants
• /
• 제31권5호
• /
• pp.205-212
• /
• 2015

In this research, effects of profile changes of stem section of the plunger on the lubrication characteristics of a fuel injection pump (FIP) were evaluated by hydrodynamic lubrication analysis. The clearance between plunger and barrel was divided into two regions, head and stem. The head was not involved in preventing a decrease of fuel oil pressure. So, research efforts were focused on both edges of the plunger’s stem. The two -dimensional Reynolds equation was used to evaluate lubrication characteristics with variations in viscosity, clearance and profile for a laminar, incompressible, unsteady-state flow. Moreover, the equilibrium equation of moment and forces in the vertical and horizontal directions were used to determine the motion of the plunger. The equations were discretized using the finite difference method. Lubrication characteristics of the FIP were investigated by comparing the dimensionless minimum film thickness, or film parameter, which is the ratio of minimum film thickness to surface roughness. Through numerical analyses, we showed that the profile of the lower edge of the stem had no effect on lubrication characteristics, but the profile of the upper edge had a significant influence on lubrication characteristics. In addition, changes in the profile were more effective in improving lubrication characteristics under low viscosity conditions.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.343-353
• /
• 1999

The role of viscosity index improver's(Ⅶ) additives for modem engine lubrication is complex. Under the condition of atmosphere or low shear rate, the characteristics of Ⅶ added lubricant is verified and quoted frequently for mathematical model of lubricant behavior. However, recent research shows that added lubricant has the characteristics of shear thinning at high shear rate condition although it performs well enough over the whole range of working temperature. At high shear rate, they show significant decrease of apparent viscosity irrespective of temperature. Many experimental researches verify that Ⅶ added lubricant shows boundary film layer formation on the solid surface as well as shear thinning effect by its polymeric molecular characteristics. The intend of our research is to verify the effects of Ⅶ from the viewpoint of continuum mechanics, because conventional Reynolds'equation with only pressure-viscosity relation cannot fully predict the lubricant behavior under the Ⅶ added condition. In these aspects, Reynolds'equation of Newtonian fluid model lacks the reflection of real fluid behavior and there is no way to explain the non-linear characteristics of Ⅶ added lubricant. In this research, we mathematically modeled the Ⅶ added lubricant behaviors which are the characteristics of non-Newtonian fluid behavior at high shear rate and boundary film formation on the solid surface. The consideration of elastic deformation in the contact region is also included in our computation and finally the converged film pressure and the film thickness with elastic deformation are obtained. The results are compared with those of Newtonian fluid model.

• International Journal of Concrete Structures and Materials
• /
• 제8권4호
• /
• pp.269-278
• /
• 2014

When concrete is being transported through a pipe, the lubrication layer is formed at the interface between concrete and the pipe wall and is the major factor facilitating concrete pumping. A possible mechanism that illustrates to the formation of the layer is the shear-induced particle migration and determining the rheological parameters is a paramount factor to simulate the concrete flow in pipe. In this study, numerical simulations considering various rheological models in the shear-induced particle migration were conducted and compared with 170 m full-scale pumping tests. It was found that the multimodal viscosity model representing concrete as a three-phase suspension consisting of cement paste, sand and gravel can accurately simulate the lubrication layer. Moreover, considering the particle shape effects of concrete constituents with increased intrinsic viscosity can more exactly predict the pipe flow of pumped concrete.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.215-223
• /
• 2003

Viscosity index improver (VII) is one of the major additives to the modern multigrade lubricants for the viscosity stability against temperature rise. However, it causes shear thinning effects which make the film thickness lessened very delicately at high shear rate $(over\;10^5\;s^{-1})$ of general EHL contact regime. In order to exactly verify the VII's performance of viscosity stability at such high shear rate, it is necessary to make the measurement of EHL film thickness down to $\~100nm$ with fine resolution for the preliminary study of viscosity control. In this work, EHL film thickness of VII added lubricant is measured with the resolution of $\~5nm$, which will give very informative design tool for the synthesis of lubricants regarding the matter of load carrying capacity at high shear rate condition.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.339-340
• /
• 2002

Natural castor oil was chemically reconstructed to extend the carbon chains by means of iso-reaction so as to improve the rheological behavior, by way of increasing the viscosity index and decreasing the pour point. The rheological and tribological characteristics of the reconstructed castor oil were comparatively investigated with those of the natural castor oil and several other vegetable oils and a mineral oil. The friction and wear test results on a four-ball machine indicate that the chemically reconstructed castor oil has considerably improved rheological and tribological properties as compared with the natural castor oil. It shows a greatly increase viscosity index and largely decreased pour point, which makes it applicable to low temperature lubrication. The chemically reconstructed castor oil even shows better tribological behavior than pentaerythritol ester or di-iso-capryl sebacate. However, it is still needed to increase the oxidation stability of the reconstructed castor oil.