• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.21-28
• /
• 2005

In the hot forging process lubricant influences on frictional condition only, but in the warm forging process it influence on the formability such as dimensional accuracy, filling state and frictional condition and it is important to estimate a lubricating characteristic of lubricants in the warm forging. In this paper, in order to evaluate the formability of billet in warm forging process according to the lubricant and lubricating method, lubricant and lubricating test have been performed using oil-based and water-based lubricant which were widely used in the hot and warm forging processes. The surface roughness of initial billet was measured to evaluate the influence on the formability of billet and the forming load and dimensional accuracy were compared and evaluated. From the experimental results, it can be known that water-based lubricants are more excellent than oil-based lubricants for warm forging of complex shape like a bevel gear. Also, in this study characteristics of deformation have been investigated according to surface treatment of initial billet.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.244-247
• /
• 2001

Lubricanting characteristics in the warm forging have influence on forgeability of products. but Research on deformation characteristic of warm forging on the lubricant and lubricating method lack. This paper deform a bevel gear by warm forging and evaluate deformation loads and quality of products by each lubricants and lubricating method using oil-based lubricants(Soy, Oildag) and water-based lubricants(Deltaforge $\#31$, Renite S-26-X, Deltaglaze $\#151$). In conclusion, the less a deformation load by lubricants the more improvement a quality of product in manufacture of a bevel gear and water-based lubricants in the warm forging reduce a deformation load and improve a quality of products. Especially, Deltaforge $\31$ have excellent characteristic in the warm forging.

• 한국유체기계학회 논문집
• /
• 제13권6호
• /
• pp.77-82
• /
• 2010

This study has conducted numerical analysis for lubrication system of transmission for commercial vehicle. The lubrication oil system in transmission can be applied to a large scale commercial vehicle which is over 15tons. The flow rate of lubricating oil has been obtained for each of branch port from the lubrication pipe. The results from numerical simulation are mainly suggested for the mass flow rate of lubrication oil in the rotating main shaft of transmission system. It has been found that the mass flow rate from oil hole increased with an rotating rate of main shaft. The flow characteristic from oil hole has been presented for the lubricating system in the manual transmission.

• Tribology and Lubricants
• /
• 제9권1호
• /
• pp.55-61
• /
• 1993

Recently, due to the erosion damage that were generated increasingly at alloy metals of slide bearing by cavity of lubricating oil with tendency of high speed and high output of reciprocating engine, there is a need to study the process on the formation of cavitation erosion, and the characteristic of cavitation erosion at lubricating oil environments under various condition for marine ship. Therefore, the apparatus of cavitation erosion experiment used 20 KHz, $24 \mu m$ piezoelectric vibrator. The main results obtained through this test method are as follows: 1. The max. erosion rate at lubricating oil environments was related to the change of space, oil film thickness, and shown to tendency of gear oil>system oil>turbine oil>mixed oil environments with different viscosity. 2. The pitted hole by cavitation erosion at high viscosity oil environments became small and deep, and in addition to, they appeared to be wide and shallow at low viscosity.

• 대한화학회지
• /
• 제23권1호
• /
• pp.52-58
• /
• 1979

금속 디알킬디티오인산염은 윤활유의 산화방지 및 내마모 첨가제로 널리 사용되고 있다. 특히 아연 DDTP가 윤활유 첨가제로서 가장 많이 사용되고 있다. 1차 및 2차 알킬기를 가진 아연, 납, 주석 및 코발트 디알킬디티오인산염을 각각 합성하였다. 합성된 각각의 금속 디알킬디티오인산염에 대하여 윤활유에서의 산화안정성, 열안정성, 금속부식성 및 내마모성을 실험검토하였다. 실험결과, 코발트 DDTP가 크롬합금강에 미치는 내마모성은 다른 화합물에 비하여 극히 우수하였으며 또한 코발트 DDTP는 일정온도 이상에서는 다갈색으로부터 청색으로 변하며 온도의 환원과 더불어 색상도 환원되는 특이한 색상의 온도 감도변화 성질이 있는 것을 알았다. 또한 모든 금속 디알킬디티오인산염은 일정 유효산 농도에 도달되어야만 윤활유의 산화 방지작용을 개시한다는 결과를 얻었다.

• 해양환경안전학회지
• /
• 제22권2호
• /
• pp.240-245
• /
• 2016

본 연구에서는 해상용 경유의 희석량에 따른 선박용 윤활유의 점도 및 전단응력의 변화 등 유변학적 거동에 대한 연구를 하였다. 연료희석에 의한 윤활유의 점도감소는 피스톤링 및 라이너의 마모로 인한 엔진내구성을 저하키는 중요한 요소이다. 연구에 사용된 윤활유는 고유황 경유(황함유량 0.05 %)를 3 %, 6 %, 10 %, 15 %, 20 %로 희석하여 magnetic stirrer를 이용, 혼합하여 제조하였다. 측정온도는 $-10^{\circ}C{\sim}80^{\circ}C$ 범위로 설정하고, 점도 및 전단응력 변화는 회전점도계인 Brookfield Viscometer를 이용하여 측정하였다. 윤활유에 해상용 경유의 희석량이 증가할수록 점도 및 전단응력이 감소하며, 이것은 상대적으로 낮은 점도의 해상용 경유가 윤활유에 희석됨에 따라 윤활유의 점도 및 전단응력이 낮아지기 때문이다. 특히, 저온($0{\sim}-10^{\circ}C$)에서는 점도 및 전단응력이 급격이 낮아지다가, $40^{\circ}C$ 이상에서는 점도 및 전단응력 감소가 해상용 경유 희석량의 영향을 거의 받지 않는다. 온도가 높아짐에 따라, 윤활유의 점도 및 전단응력 감소는 윤활유의 뉴턴유체 거동을 보이는 것을 확인했다. 경유의 혼입에 의한 점도감소로 선박의 엔진마모를 촉진할 수 있으므로 엔진의 내구성 향상을 위해 윤활유의 주기적인 관리가 필요하다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.263-264
• /
• 2002

The tribological characteristic of several environmentally friendly lubricating base stocks was examined, and the effect of some commonly used additives on th tribological behavior of the lubricating oils was comparatively investigated on a four-ball machine. It has been found that the commercial additives including butene sulfide, wax chloride, zinc dialkyldithiophosphate and ashless P-N type agent helped to improve the friction-reducing and antiwear properties as well as the extreme pressure behavior. Non-toxic nanoscale $(CF)_x$ showed the best friction-reducing ability, though it registered relatively poor extreme pressure properties. The mechanism on friction of nano-scale material is discussed.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.29-35
• /
• 1988

When low sliding velocities in the boundary lubrication range are operating, irregular movements frequently occur which are a result of the stick-slip phenomenon. Such slide motions are undesirable in precision machine tools, particularly with feed back systems used in numerical and adaptive control machine tools. Accordingly, this paper reports analytical and experimental studies in the stick-slip characteristic of machine tool feeding system. The main conclusions of this study are as follows; The tendency towards stick-slip effects may be reduced by; 1). Reducing the drop in friction coefficient in the Stribeck curve(on the rising part of the friction characteristic at higher sliding speeds, the system is stable all the time) 2). Reducing the transition velocity by the use of a higher viscosity lubricating oil. 3). Increasing the stiffness(Damping)and reducing normal load(Sliding mass) Therefore, the Critical velocity is decided from the above conclusions and in designing of machine tool, feed rates(sliding velocity)must be design the more than critical velocity.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.79-87
• /
• 1999

The most part of the faculty drop a trouble and damage of machine equipment even if whatever cause they break out take place at local and trifling place and the factor dominating their trouble is due to wear debris occurred in the lubricated machine moving surface. This study has been car-ried out to identify morphology of wear debris on the lubricated machine moving system by means of computer image analysis. Namely the wear debris contained in lubricating oil extracted from movable machine equipment will be filtered through membrane filter(void diameter 0.45${\mu}m$) and will be analyzed with its data information such as 50% volume diameter aspect roundness and reflectivity. Morphological characteristic of wear debris is easily distinguished by four shape parameters it is necessary to divide small class of every 100 wear debris in total wear particles in order to distinguish morphological characteristic of wear debris more easily by computer image analysis. We are sure that operation condition diagnosis of the lubricated machine moving surfaces is possible by computer image analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.149-154
• /
• 2007

The zinc prosphate film treatments used to lubricating treatment of mostly cold forging processes. But there are several problems happened to lubricating treatment process such as happening harmful environment on person, complex lubrication processing occurring in energy and time consumption, eco-destructive and chemical by-product generation, the needs of waste disposal etc. As a result, a water-soluble lubricant was developed to replace the perfect or some of the zinc prosphate film in the world. In order to solve these problems, this study evaluated the performance of the typical water-soluble. In this study, for these requirement inquiry of two part. First, about possibility of replace zinc phosphate lubricant, quantitatively evaluation developed of water-soluble lubricant for cold forging vs zinc phosphate lubricant. Second, About optimization of coating Process use to equipment with practicable automatic coating Process. The performance evaluation of these lubricants was conducted using the double cup extrusion test and spike forging test. With the use of the commercial FE code DEFORM, friction factor calibration curves, i.e. cup height ratio vs. punch stroke and spike height vs. punch stroke, were established for different friction factor values. By matching the cup height ratio and the punch stroke and spike height vs. punch stroke from experiment to that obtained from FE simulations, the friction factor of the lubricants was determined. Survey of comparative analysis use to SEM that sprayed lubricant surface structure of grain shape and characteristic of lubricant performance based on grain shape and deformed lubricant surface expansion. As a result, developed lubricant were found to perform comparable to or better than zinc phosphate. And thought this result, innovatively cope with generated problem of existing lubrication process.