• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.82-87
• /
• 1997

Large dynamic loads act on the rotor in rotary compressors. There are unbalance forces due to eccentric parts and gas forces induced by the pressure difference between compression and suction gases. Rotor-journal bearing system is nonlinear since the stiffness and damping coefficients of the lubricating oil film are not constant in the bearings. The system is considered as a coupled problem of flexible rotor and the journal bearings. Bearing reaction force is calculated from pressure of oil film using Reynolds equations in journal bearings. Pressure distribution in journal bearing is analyzed by finite difference method. The dynamic response of rotor and bearing characteristic are discussed when rotary compressor has a relative misalignment.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.136-141
• /
• 2008

Due to environmental concerns $CO_2$ has been reintroduced as a potential candidate to replace HFCs in refrigeration systems since 1990s. In a refrigeration cycle, oil is utilized in lubricating a compressor. However, although oil separators are installed after a compressor oil is prone to leak to the whole system. The mixing of $CO_2$ and oil, even a small amount of oil, the heat transfer performance in heat exchanger deteriorated and the pressure drop inside tube increases. Therefore, it is needed to precisely estimate the mixture thermodynamic properties of $CO_2$-lubricant oil to correctly design a $CO_2$ refrigeration system. The commonly used method in estimating the mixture properties is the mole based weighting model. However, the accuracy of the method can not be assured. In the present study, $CO_2$-lubricant oil mixture properties including viscosity and density were estimated by using the mixture models, based on the equation of state (EOS).

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권10호
• /
• pp.483-493
• /
• 2001

The 3-phase induction is used for the MCP(main coolant pump) and the pure water is used for lubrication of bearing because of the difficulty of repair. Therefore the type of motor is the canned-motor that is welded by sealed can to prevent the stator and rotor from the lubricating water. A lot of Eddy currents are produced in the can because of the conductivity of material. And these eddy currents in the can are the most important cause that decrease the efficiency of induction motor. Therefore we have to find the method to decrease these eddy currents in the can for the improvement of efficiency of motor. In this paper, we proposed the method of design and analysis of canned-motor using equivalent circuit with consideration of can loss for the improvement of efficiency of motor.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.56-60
• /
• 2009

A journal bearing is used in a hydrodynamic lubrication state, but it becomes a boundary lubrication state that asperity of a contact part touch each other when pressure is too high and an enough oil film is not formed by viscosity change due to lubricating oil temperature. At this time, abrasion due to contact between a journal and a bearing is unavoidable, and scuffing damage that the journal adheres to the bearing occurs if the process is repeated. Damage of the journal bearing is an important problem because it gives huge damage to a machine and can generate large accidents such as economic loss and human life damage. In this study, method for using the pull-up resistor concept was introduced as the monitoring technology. This monitoring system is important to enhance reliability of the engine.

• 한국응용과학기술학회지
• /
• 제19권2호
• /
• pp.117-122
• /
• 2002

A silicone softner (SS-5), a permanent press (PP) finish, was prepared by blending silicone oil KF-96 (as a lubricating component) and beef tallow hardened oil (as a softening component) which was synthesized from fatty polyamide salts. The prepared SS-5 and the PP finishing resin were applied to PP finishing cotton cloth and P/C gingham sample by one-bath method. The properties such as crease recovery, tear strength, and bending resistance were tested. The samples treated with SS-5 and PP finishing resin showed improved properties when comparing with the untreated ones, with the ones treated only with PP finishing resin, with ones treated with commercial PP finishing softners and PP finishing resin. The grades of fabric samples treated with 3% SS-5 were fifth grade in the bending resistance test.

• 드라이브 ㆍ 컨트롤
• /
• 제20권1호
• /
• pp.41-47
• /
• 2023

The aim of this study was to develop a method for installing strain gauges on moving, lubricating oil-filled, and sealed parts, such as drive shafts of equipment, including construction machinery. A measuring device was constructed using an embedded CPU and an IoT sensor to measure the strain of the strain gauge, which allowed for the measurement of axial torque and axial force, and subsequent analysis. To verify the performance of the developed device, the axial torque and axial force of the forklift were measured during operation using a strain gauge attached to the inside of the drive shaft. This study confirmed the possibility of measuring and analyzing the strain of a moving part, such as the inside of a drive shaft, which is sealed and filled with hydraulic oil.

• 공업화학
• /
• 제19권1호
• /
• pp.51-58
• /
• 2008

내마모제로 사용하기 위하여 mercaptobenzothiazole 및 디알킬렌디티오카바메이트 그룹을 함유하는 환경친화적인 올레인산 에스테르를 디알킬아민과 이황화탄소의 치환반응, 디클로로아세톤과의 치환반응, $NaBH_4$을 사용한 환원반응 및 올레인산과의 축합반응 등의 과정을 행하여 90% 이상의 수율로 합성하였다. 중간 생성물 및 내마모제의 구조적 특성은 FT-IR, $^1H$-NMR 스펙트럼 및 원소분석으로 분석하였으며 광유계 오일(100 N) 및 식물유에서의 용해성을 1 중량%에서 평가한 결과 잘 용해되었다. 또한, 합성한 내마모제의 열 안정성을 TGA로 분석하였으며 초기 5 wt% 분해온도가 구조에 따라 $192^{\circ}C$에서 $217^{\circ}C$의 안정성을 나타내었다. CEC L-33-A-93 방법으로 생분해도를 평가한 결과 89%에서 99%의 생분해도를 나타내어 환경친화적인 내마모제임을 확인하였다. 내마모제의 윤활특성을 100 N 윤활기유 및 식물유에 첨가하여 4구 마모시험기를 사용하여 평가한 결과, 100 N BO에서 4-ball 마모흔의 직경은 Bz-thia-OE < C4-DTC-OE < Pyrro-DTC-OE < C8-DTC-OE의 순으로 큰 값을 나타내어 내마모성능이 나쁘게 나타났다. 한편, 식용유에서는 4-ball 마모흔의 직경이 0.8260 mm에서 0.9637 mm를 나타내어 내마모제의 첨가효과가 나타나지 않았다.

• 분석과학
• /
• 제16권5호
• /
• pp.339-348
• /
• 2003

본 연구에서는 동시 형광분광법과 GC/FID법을 이용하여 폐윤활유 시료 중의 PAHs를 acetonitrile 용매로 추출하여 정량분석 하였다. 동시 형광분광법을 이용하여 7종의 PAHs, 즉 acenaphthene (Ace), anthracene (Anth), benzo(a)pyrene (BaP), chrysene (Chry), phenanthrene (Phen), fluoranthrene (Fl) 및 perlyrene (Per)을 분석하였다. 이들 성분의 검정선은 모두 0.4~166 ppb(상관계수; 0.9985~0.9999)의 범위에서 직선을 보였다. 다른 8종의 PAHs를 GC법으로 분석하기 위한 검량선은 10.0 ppm 표준용액을 사용하였고, split ratio를 10에서부터 100까지 변화시킬 때에 발생되는 peak 면적을 이용하여 작성하였다. 검출감도는 동시 형광분광법이 GC법보다 적어도 100배 이상 우수하였다. 폐윤활유 시료 중의 총 PAHs 함량은 LNG(버스)와 LPG(택시)의 폐윤활유에서 각각 5.5 ng/g과 10.5 ng/g의 수준으로 검출되었으며, 가솔린을 사용하는 일반승용차, 경유를 사용하는 승합차 및 트레일러의 폐윤활에서 각각 92.2 ng/g, 92.6 ng/g 및 130.3 ng/g 등이 측정되어 경유를 사용하는 대형트레일러에서 가장 많은 양이 발생됨을 알 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.778-781
• /
• 2002

Durability of rubber dust cover in the ball joint for automotive suspension parts were analyzed by FEM and compared with experimental data. Upper open area of ball joint is sealed by dust cover for preventing outflow of the lubricating oil and intrusion of send, dust, water, etc. This rubber cover undergoes repeated loadings such as tension and compression while the car is running. Analysis about rubber material needs to consider every kinds of nonlinearities arise in finite element analysis, which are geometric nonlinearity due to large displacement and small strain, materially nonlinearity and nonlinear boundary condition such as contact. So in the study, the deformation behavior of dust cover was analysed by using the commercial finite element program MARC. This program could solve these kinds of nonlinear analysis accurately. Finite element model of dust cover is considered as 3-dimensional half model based on 2-dimensional axisymmetric model. Material property of rubber was modeled by Ogden model and input data for calculation takes form uniaxial tension test of rubber specimen, The final object of the study is obtaining the design specification of dust covers and the result of analysis should be a useful data to design of rubber

• 해양환경안전학회지
• /
• 제7권2호
• /
• pp.1-11
• /
• 2001

Many investments and works being continued to preserve green ocean in each countries of the world. Especial1y, the researches on the prevention of marine oil pollution being strengthened. It is not easy to disclose sludge oils that were produced necessarily in the ships operation, so that they are transferred to shore treating facility after collected inside the ship＇s sludge tank mostly. However, this shore transferring method is not only costly and time consuming but also entails risk of oil pollution. In this regard, it will be the best way to manage the sludge oils inside ship itself. The purpose of this study is to device an ultrasonic breaking systems which recycle the sludge oil from ships into usable oil to be burnt. In this paper, the first place, matrix structures of sludge fuel oil(SFO) and sludge lubricating oil(SLO) with the irradiation time for ultrasonic vibrator were interpreted. And, erosion damage for vibrator horn tip which is one of important part of ultrasonic breaking systems was examined under such an environment of the sludge oils. The material for horn tip is being made of SS41 steel and its erosion phase was investigated with variation of the vibration amplitude of 50${\mu}{\textrm}{m}$ and 24${\mu}{\textrm}{m}$ as well as the change of temperature in the oil environments. It is suggested that the experimental results can be helpful to the development of sludge oil disposing systems for the vessel.