• Tribology and Lubricants
• /
• 제18권2호
• /
• pp.105-108
• /
• 2002

Specially designed grooved journal bearings are installed in the main coolant pump for SMART (System-integrated Modular Advanced ReacTor) to support radial load on the rotating shaft. The canned motor type main coolant pumps are arranged vertically on the reactor vessel and filled with circulating primary coolant which is pure water. The main coolant pump bearings are lubricated with this coolant without any other external lubricant supply. Because lubricating condition is too severe for this bearing to generate proper hydrodynamic film, investigation of lubrication characteristics of the journal bearing is important to satisfy life constraint of whole pump system, and the results will be applied to the analysis of dynamic characteristics of the shaft system. The bearing is made of silicon graphite which has self$.$lubricating effect. A lubrication analysis method is proposed for this vertically grooved journal bearing in the main coolant pump of SMART, and lubricational characteristics of the bearings are examined in this paper.

• 공업화학
• /
• 제23권4호
• /
• pp.421-427
• /
• 2012

초저유황 경유의 윤활성능을 향상시킬 목적으로 식물유 기반 알칸올 아마이드 유도체를 합성하여 윤활성능을 평가하였다. 알칸올 아마이드 유도체는 폐식물유(다크오일), 팜유, 코코넛유를 메탄올과의 연속 전이에스테르화 반응을 통하여 합성한 지방산 메틸에스테르와 디에탄올아민(DEA)의 아마이드화 반응을 행하여 합성하였다. 합성한 알칸올 아마이드 유도체는 1 wt% 범위 내에서 초저유황 경유에 잘 용해되었으며, 이 유도체를 120 ppm 포함한 초저유황 경유의 윤활성능을 HFRR법으로 측정하였다. 그 결과, 초저유황 경유의 마모흔의 직경이 581 ${\mu}m$에서 아마이드 첨가 후 305~323 ${\mu}m$으로 현저히 작아져 초저유황 경유의 윤활성능을 향상하는 것으로 확인되었다. 한편, 식물유의 종류에 따른 마모흔의 차이는 크지 않아 알칸올 아마이드 유도체의 알킬기의 구조에 따른 윤활성능의 차이는 크게 나타나지 않았다. 알칸올 아마이드 한 종류를 선정하여 첨가 농도에 따른 윤활성능을 평가한 결과, 농도에 따라 마모흔의 직경이 현저히 작아지는 결과를 얻었는데 이는 윤활성능이 첨가 농도에 따라 향상되는 것을 의미한다.

• 한국응용과학기술학회지
• /
• 제30권4호
• /
• pp.715-725
• /
• 2013

바이오디젤은 세계 화석연료의 흐름을 변화시킬 수 있는 환경 친화적 대체물질로 관심의 대상이 되고 있으며 대체연료 외에도 다양한 분야에서 수많은 응용 연구가 진행되고 있다. 최근에는 원유의 정제로부터 얻어진 석유제품을 대체하려는 다양한 움직임이 활발하게 진행되고 있다. 그 중 윤활기유로서의 식물성 오일은 급속도로 발전된 석유산업으로 인해 상용화 되지 못했던 오일로 관심의 대상이 되고 있으며 자연친화적 생분해성과 무독성, 윤활유로서의 낮은 휘발성과 우수한 계면윤활 등 대체 오일로써 충분한 가능성을 지니고 있다. 하지만 우수한 윤활 및 마모성능에도 불구하고 윤활연구에 넓게 활용되지 못했던 이유 중에는 지방산메틸에스테르가 갖는 열악한 산화안정성(oxidation stability) 및 열화안정도(thermal stability) 때문으로 보고되고 있다. 따라서 바이오디젤을 윤활기유 내 일정비율로 혼합하여 윤활성능 및 산화안정성의 변화를 확인하였으며 사구식 내마모 성능시험 후 발생되는 산화 및 열화현상을 알아보았다. 또한 산화에 따른 혼합 오일의 윤활특성 변화를 분석하였으며 이러한 결과를 바탕으로 윤활유 또는 윤활 향상제로서의 가능성을 살펴보았다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.587-591
• /
• 1997

The DGs (Diesel Generators) in NPP (Nuclear Power Plant) has been used for the emergency electric power source to shut down the nuclear reactor safely in case of station blackout. The RCM (Reliability Centered Maintenance) has been applied to DGs for increasing the safety of NPP. The structured defects of DG were not remedied by the improvement of maintenance method. As the first stage of RCM, to find the structured defects, its failure modes were searched and analyzed through the ten year maintenance information. The structured defects such as the air compressor, the lubricating oil pressure, and the insufficient load were the root causes of main failures. The air reservoir reinstallation, the lubricating oil tube modification, the load bank installation, and the qualitative instrumentation were the solutions for the hardware oriented RCM of DGs. There remains the software oriented RCM such as the rejection of useless maintenance, the preventive maintenance, the database of maintenance information, and the predictive maintenance.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.469-476
• /
• 1983

The effects of oil supply conditions on the static and dynamic properties of journal bearings supporting high speed rotors were investigated. The initially unknown hydrostatic pressure in oil pockets were determined by iteration with the aid of the equation of oil flow balance for given oil supply pressure and flow coefficients of oil inlet. For the calculation of dynamic characteristics, the dynamic changes of pressure in lubricating gaps and oil pockets were linearised with a perturbation method.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.665-668
• /
• 2006

Concrete secondary product that use cement is increasing application from reason of shortening etc.. of construction period in construction site. Manufacture method of construction of this concrete secondary product there is hot-check method, direct spray method, press method, extrusion molding method etc.. Also, I am using reinforcement boating certainly in this process. In most case, We have used asbestos by reinforcement fiber until early 90s but use from human body hurtfulness controversy is felt constraint. Therefore, application of principal parts fiber is increasing. But, to replace asbestos, because must satisfy all lubricating ability, productivity etc.. class, it is the very difficult matter to replace asbestos. In this study, I wished to do Test about asbestos principal parts possibility at extrusion process to charge shape or form making test piece because mixs polypropylene fiber etc. by plan that replace asbestos in cement extrusion molding product and measures bending strength and elasticity.

• 한국재료학회지
• /
• 제14권1호
• /
• pp.59-66
• /
• 2004

In the present study, ceramic brake pads without fiber phases were manufactured by the low temperature heat treatment below$ 700 ^{\circ}C$. The manufacturing parameters of ceramic brake pads and those levels were investigated by the analysis results of signal-to-noise ratios, ANOVA based upon the Taguchi method. The ceramic brake pads prepared in the Mg experiment had a friction coefficient of 0.30～0.55 very close to the target coefficient (0.35～0.45) of commercial brake pads utilized in the automobiles. The frictional properties of ceramic brake pads could be stabilized with the adjustment of amounts of lubricating additives. The optimum preparation conditions as well as batch formulations for the fabrication of non-fibrous ceramic brake pads were finally determined using Taguchi method in this study.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.19-24
• /
• 2003

Recently, various efforts to make more speedy and precision machine tool to improve productivity and also various efforts to solve environmental problem are going on, so that dry cutting in manufacturing industry, which needs environmental conscious design and development of manufacturing technique, is becoming a very important assignment to solve. Because dry cutting does not use cutting fluid, we need other methods that can be used instead of cutting fluid, which does cooling, lubricating, chip washing, and anti-corrosion. Especially, because turning is a continuous work, the consideration of tool life and surface roughness due to continuous heat and poor lubrication is important. The purposes of this paper are the consideration of how well the compressed air can work instead of cutting fluid, and also the development of the method to select the optimum machining condition by the minimum numbers of experiments through the Taguchi method.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.1028-1034
• /
• 2007

In order to establish a criteria of solid particle separation performance test on marine centrifugal purifier at factory acceptance test, an investigation had been done on criteria of test standards, regulations and test specifications of purifier manufactures. KS V 7836, fuel oil and lubricating oil purifiers for marine use-centrifugal type, the criteria of solid particle separation is studied in the point of reality, restricts and analysis method. It is proposed that a reasonable criteria and analysis method should be adopted, and the current criteria shall be revised to adequate levels considering reasonable basis and industrial technology levels. Also, the test analysis conceptions, separation efficiency method and particle size restriction method, are reviewed to fulfil separation performance test for marine centrifugal purifiers.

• 한국기계기술학회지
• /
• 제13권4호
• /
• pp.49-55
• /
• 2011

Recently, various efforts to make more speedy and precision machine tool to improve productivity and also various efforts to solve environmental problem are going on, so that dry cutting in manufacturing industry, which needs environmental conscious design and development of manufacturing technique, is becoming a very important assignment to solve. Because dry cutting does not use cutting fluid, we need other methods that can be used instead of cutting fluid, which does cooling, lubricating, chip washing, and anti-corrosion. Especially, because turning is a continuous work, the consideration of tool life and surface roughness due to continuous heat and poor lubrication is important. The purposes of this paper are the consideration of how well the compressed air can work instead of cutting fluid, and also the development of the method to select the optimum machining condition by the minimum numbers of experiments through the Taguchi method.