• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.30-38
• /
• 1994

The thermohydrodynamic(THD) performance of a large tilting pad journal bearing is investigated both theoretically and experimentally. The theory takes into account the three dimensional variation of lubricant viscosity and eddy viscosity, and the inlet pressure. Owing to the inlet pressure effect, the film pressure and load capacity are increased but the mixing temperature and bearing surface temperature are decreased. The continuous distribution of the film pressure and film thickness and the bearing surface temperature are measured along with the shaft speed and the bearing load, and they are compared with the theoretical results. The results obtained by the experiment are in good agreement with those by the theory including the inlet pressure effect. It is suggested that the three dimensional turbulent THD analysis including the inlet pressure effect is very useful to predict the performance of the large tilting pad journal bearing more accurately.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.267-271
• /
• 2002

Most studies of elsatohydrodynamic lubrication are oriented only to the measurement of film thickness itself with optical interferometer. In order to exactly investigate the characteristics of a certain lubricant, it is also important to get the information of traction force as well. In this work, we developed the device for measuring friction force of ehl contact condition together with the film thickness. To verify the validity of the measuring system, the friction force and film thickness under ehl condition are measured with the variation of additive ratios of viscosity index Improvers.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.184-188
• /
• 2008

It has been recognized that friction coefficient decreased with decreasing viscosity of oil in lubrication. In general, the more viscosity decreases, the more wear rate increases due to decrease load carrying capacity. It has been proposed that nano particles in oil decrease friction coefficient and wear rate. The purpose of this study is to apply oil of lower viscosity that mix with nano particles at the compressor used in a refrigerator to decrease friction coefficient keeping Load carrying capacity. Mineral oil of 8 cSt were used and mixed with nano particle. Friction coefficient was evaluated by a disk-on-disk tester. As a result, friction coefficient of nano oil decreased by 90% in comparison with raw oil. These results lead us to the conclusion that nano oil is new plan to raise efficiency of the compressor.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.5
• /
• pp.492-497
• /
• 2015

Currently, there are many kinds of tracked armored vehicles in service and they have encountered various environment and situations. So there are many obstacles to operate them improperly such as an engine stall. The causes of engine stall are an insufficient fueling, a mixture of air-fuel or vapor lock, and load increment which results from a rapid steering or increasing a viscosity of lubricant by low temperature. In this paper, engine stall by load increment due to a rapid steering or increasing of lubricant viscosity on tracked armored vehicles is analyzed, the ways to prevent it are applied, and their degrees of improvement are evaluated.

• Tribology and Lubricants
• /
• v.39 no.3
• /
• pp.87-93
• /
• 2023

Nanofluids are dispersions of particles smaller than 100 nm (nanoparticles) in base fluids. They exhibit high thermal conductivity and are mainly applied in cooling applications. Nanolubricants use nanoparticles in base oils as lubricant additives, and have recently started gathering increased attention owing to their potential to improve the tribological and thermal performances of various machinery. Nanolubricants reduce friction and wear, mainly by the action of nanoparticles; however, only a few studies have considered the rheological properties of lubricants. In this study, we adopt a parallel slider bearing model that does not generate geometrical wedge effects, and conduct thermohydrodynamic (THD) analyses to evaluate the effect of higher thermal conductivity and viscosity, which are the main rheological properties of nanolubricants, on the lubrication performances. We use a commercial computational fluid dynamics code, FLUENT, to numerically analyze the continuity, Navier-Stokes, energy equations with temperature-viscosity-density relations, and thermal conductivity and viscosity models of the nanolubricant. The results show the temperature and pressure distributions, load-carrying capacity (LCC), and friction force for three film-temperature boundary conditions (FTBCs). The effects of the higher thermal conductivity and viscosity of the nanolubricant on the LCC and friction force differ significantly, according to the FTBC. The thermal conductivity increases with temperature, improving the cooling performance, reducing LCC, and slightly increasing the friction. The increase in viscosity increases both the LCC and friction. The analysis method in this study can be applied to develop nanolubricants that can improve the tribological and cooling performances of various equipment; however, additional research is required on this topic.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.15-18
• /
• 2013

The next generation alternative fuel of diesel, DME (Dimethyl Ether) discharges particulate matter hardly due to chemical structural as oxygen-fuel so it has the eco-friendly property. Despite these advantages, the DME has the technical difficulties to apply to the diesel engine because of a low calorific value, viscosity and compressibility effects. From this point of view, we performed experimental studies on improved reliability of DME common-rail vehicle and lubricity enhancement of DME fuel for empirical distribution of eco-friendly DME fuel. Also we analyzed solubility of lubrication enhancer according to a drop in temperature, try to secure reliability about core parts of DME vehicle by applying lubrication enhancer in the DME common-rail vehicle.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.83-89
• /
• 2000

This paper presents a pressure drop correlation for evaporation and condensation of alternative refrigerant with oil in micro-fin tubes. The correlation was developed from a data base consisting of oil-free pure and mixed refrigerants in micro-fin tube; Rl25 R134a. R32 R410a(R32/R125 50/50% mass), R22, R407c(R32/R125/R134a, 23/25/52% mass) and R32/R134a(25/75% mass). The micro-fin tube used in this paper had 60 0.2mm high fins with a 18 helix angle. The cross sectional flow area $(A_c)$ was $60.8 mm^2$ giving an equivalent smooth diameter$(D_e)$ of 8.8mm. The hydraulic diameter $(D_h)$ was estimated to the 5.45mm. The new correlation was obtained by replacing the friction factor and the tube-diameter in Bo Pierre correlation by a friction factor derived from pressure drop data for a micro-fin tube and the hydraulic diameter, respectively. This correlation was also used to predict some pressure data with a lubricant after using a mixing viscosity rule of lubricants and refrigerants. As a result, the new correlation was also well predicted to the measured data within a mean deviation of 19.0%.

• Tribology and Lubricants
• /
• v.36 no.1
• /
• pp.11-17
• /
• 2020

In manufacturing operations, oil plays a crucial role in reducing friction and wear among interacting surfaces at varying velocities, loads, and temperature. Hydrocarbon oil is considered the origin of lubrication oils. However, this base oil has been limited in its use as it is a principal cause of pollution. This research focuses on identifying a biodegradable base oil lubricant that possesses a stable coefficient of friction and viscosity with temperature. Friction analysis is conducted by employing a pin on a disk tribotester with a fixed load of 10 N at varying sliding speeds ranging from 0.06 m/s to 0.34 m/s. Oil viscosity analysis is perfomed at room temperature by using a rotary viscometer. Tests are performed using canola oil and paraffin oil as lubricants. The results indicate that the viscosity of canola oil is more efficient than paraffin oil. The non-dimensional characteristic number according to the Stribeck curve reveals an elastohydrodynamic lubrication regime with canola oil lubrication. A comparison of both lubricants reveals that, the friction efficiency of canola oil and paraffin oil does not differ considerably. However, the friction in canola oil is observed to decrease more than that in paraffin oil at an elevated sliding speed. The tests confirm that canola oil is potent in minimizing the friction coefficient of SCM440 bodies interacting with one another as well as acted upon by load.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.22-27
• /
• 2006

The effect of transesterification on the rheological property of poly(ethylene naphthalate)/poly(butylene tore-phthalate) (PEN/PBT) blends has been investigated. The melt viscosity of PEN/PBT blends decreased with increasing PBT content due to the relatively low melt viscosity of PBT as well as introducing ransesterification between PEN and PBT Further melt viscosity decrease was achieved by the thermal annealing which caused both the chain scission and the acceleration of transesterfication. Calcium stearate (CaST) was applied as a lubricant in order to lower the melt viscosity of PEN and it was found that CaST was acting as the catalyst of transesterification as well. In general, reactive melt blending of PEN and PBT by transesterification resulted in the decrease of molecular weight of PEN and PBT, as a result, the loss of mechanical properties in PEN/PET blend was inevitable.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.118-123
• /
• 2006

The effect of transesterification on the rheological properties in the melt reactive blending of poly(butylene terephthalate)(PBT) with poly(ethylene terephthalate)(PET) has been studied. The melt viscosity depression in PBT was found in PBT/PET blends due to the intrinsic low melt viscosity of PET compared to PBT. In addition, the thermal degradation in the melt blending and transesterification between two polyesters were considered as other factors fer the lowering of the melt viscosity in the blends. In the PBT/PET blends, calcium stearate was less effective than in PBT as a lubricant, however it accelerated both the thermal degradation and transesterification during melt blending. As a result, further melt viscosity drop was obtained in the reactive melt blending of PBT/PET.