• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.148-152
• /
• 2005

Atmospheric low-temperature plasma was produced using dielectric barrier discharge (DBD) plate-type plasma reactor and high frequency of 13.56 Hz. The surfaces of polyimide films for insulating and packaging materials were treated by the atmospheric low-temperature plasma. The contact angle of 67$^{\circ}$ was observed before the plasma treatment. The contact angle was decreased with deceasing the velocity of plasma treatment. In case of oxygen content of 0.2 %, electrode gap of 2 mm, the velocity of plasma treatment of 20 mm/sec, and input power of 400 W, the minimum contact angle of 13$^{\circ}$ was observed. The chemical characteristics of polyimide film after the plama treatment were investigated using X-ray photoelectron spectroscopy (XPS), and new carboxyl group bond was observed. The surfaces of polyimide films were changed into hydrophilic by the atmospheric low-temperature plasma. The polyimide films having hydrophilic surface will be very useful as a packaging and insulating materials in electronic devices.

• 한국분무공학회지
• /
• 제18권1호
• /
• pp.21-26
• /
• 2013

Diesel low temperature combustion (LTC) is the concept where fuel is burned at a low temperature oxidation regime so that $NO_x$ and particulate matters (PM) can simultaneously be reduced. There are two ways to realize low temperature combustion in compression ignition engines. One is to supply a large amount of EGR gas combined with advanced fuel injection timing. The other is to use a moderate level of EGR with fuel injection at near TDC which is generally called Modulated kinetics (MK) method. In this study, the effects of fuel injection pressure on performance and emissions of a single cylinder engine were evaluated using the latter approach. The engine test results show that MK operations were successfully achieved over a range of with 950 to 1050 bar in injection pressure with 16% $O_2$ concentration, and $NO_x$ and PM were significantly suppressed at the same time. In addition, with an increase in fuel injection pressure, the levels of smoke, THC and CO were decreased while $NO_x$ emissions were increased. Moreover, as fuel injection timing retarded to TDC, more THC and CO emissions were generated, but smoke and $NO_x$ were decreased.

• 전기전자학회논문지
• /
• 제18권2호
• /
• pp.185-191
• /
• 2014

본 연구에서는 저온유동성 성능검사 시스템 구현을 통해 디젤 차량용 통합형 연료히터의 성능을 평가한다. 저온유동성 시험장치에서 $+20{\sim}-30^{\circ}C$ 온도범위에 따라 분리형과 통합형 연료히터 성능을 비교하고, 필터 전후에 따라 유압과 시동시간, 히터의 소모전력을 측정한다. 이때 다양한 종류의 필터면적을 사용함으로써 통합형 연료히터와 분리형을 비교한 결과 시동 시간이 23% 향상되었고, 저온시동성능은 19% 정도 향상된다.

• 한국안전학회지
• /
• 제28권3호
• /
• pp.18-22
• /
• 2013

The Co-base super heat resisting alloy ECY768 is employed in gas turbine because of its high temperature strength and oxidation resistance. The prediction of fatigue life for superalloy is important for improving the efficiency. In this paper, low cycle fatigue tests are performed as variables of total strain range and temperature. The relations between strain energy density and number of cycle to failure are examined in order to predict the low cycle fatigue life of ECY768 super alloy. The lives predicted by strain energy methods are found to coincide with experimental data and results obtained from the Coffin-Manson method. The fatigue lives is evaluated using predicted by Coffin-Manson method and strain energy methods is compared with the measured fatigue lives at different temperatures. The microstructure observing was performed for how affect able to low-cycle fatigue life by increasing the temperature.

• 해양환경안전학회지
• /
• 제25권3호
• /
• pp.328-333
• /
• 2019

During the winter of 2017/2018, significantly low water temperatures were detected around the western and southern coasts of Korea (WSCK). In this period, sea surface temperature (SST) in the Korea Waters was about $2^{\circ}C$ lower than mean temperature. Using the real-time observation system, we analyzed the temporal variation of SST during this period around the western and southern coasts. Low water temperature usually manifested over a period of about 10 ~ 20 days. The daily Arctic oscillation index was also similarly detectable with the variation of SST. From the cross-correlation function, we compared two periodic variations, which were SST around the WSCK and the Arctic oscillation index. The cross correlation coefficients between both variations were approximately 0.3 ~ 0.4. The time lag of the two time series was about 6 to 7 days. Therefore, significantly low water temperatures during winter in the Korean coastal areas usually became detectable 6 to 7 days after the negative peak of Arctic oscillation.

• Journal of Forest and Environmental Science
• /
• 제38권4호
• /
• pp.284-289
• /
• 2022

This study was conducted to determine the seed dormancy types of Sambucus racemosa subsp. pendula Nakai and S. williamsii Hance. Low temperature stratification (1, 2, 3, 4 months) and GA3 treatment (1,000 mg/L) were performed on seeds to determine the type of seed dormancy. After the treatment, seeds were placed on a petri dish at 25℃ under light conditions. The germination rate and mean germination time were investigated. Results showed that cold stratification was effective in breaking the dormant state of the seed in both species. In the low temperature stratification treatment, the seed germination performance was improved as the treatment period was prolonged. Gibberellin treatment was effective in breaking the dormant state of S. racemosa subsp. pendula without low temperature stratification. However, S. williamsii did not break the dormant state of the seed by gibberellin treatment without low temperature stratification treatment. In the gibberellin treatment, germination performance was improved according to the low temperature stratification treatment period. As a result of this study, the seeds of S. williamsii have both an intermediate complex and a deep complex morphophysiological dormancy (MPD). In comparison, it was found that the S. racemosa subsp. pendula had intermediate composite MPD.

• 소성∙가공
• /
• 제33권3호
• /
• pp.185-192
• /
• 2024

This study examined how varying tempering temperatures affect the susceptibility of Cr-Mo low alloy steels to hydrogen embrittlement. A slow strain-rate test (SSRT) was carried out on the steels electrochemically pre-charged with hydrogen in order to examine the hydrogen embrittlement behavior. The results showed that the hydrogen embrittlement resistance of the Cr-Mo low alloy steels improved with increasing tempering temperature. Thermal desorption analysis (TDA) revealed that diffusible hydrogen content decreased with increasing tempering temperature, accompanied by a slight increase in the peak temperature. This decrease in hydrogen content was likely due to a reduction in dislocation density which served as reversible hydrogen trap sites. These findings underline the significant role of tempering temperature in enhancing the hydrogen embrittlement resistance of Cr-Mo low alloy steels.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.1131-1134
• /
• 2003

A low temperature doping technique has been studied for application in poly-Si TFT's on plastic substrates. Heavily-doped amorphous silicon layers were deposited on poly-Si and the dopant atoms were driven in by subsequent excimer laser annealing. The entire process was carried out under a substrate temperature of $120^{\circ}C$, and a sheet resistance as low as $300 {\Omega}/sq$. was obtained.

• 한국전기전자재료학회논문지
• /
• 제15권11호
• /
• pp.976-980
• /
• 2002

This paper repors on low temperature sealing process of PDP using binder and capping glass. The exhausting hole on rear glass of PDP was sealed by capping glass using screen-printed binder without exhausting glass tube. Based on the tubeless packaging process, out gassing problem could be reduced and vacuum conductance could be improved by eliminating exhaust tube.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.896-899
• /
• 2003

Using hi plasma and Fe-Phthalocyanine, carbon nanofibers have been synthesized a low temperature. The carbon nanofibers had about In nm diameter and up to $10{\mu}m$ length. These were grown in random orientation. There are two shapes in the CNFs, screw and straight line shapes. Furthermore, we found the selective growth of nanofibers on the scratched substrates.