• 마이크로전자및패키징학회지
• /
• 제29권2호
• /
• pp.99-105
• /
• 2022

칩사이즈가 작아짐에 따라 선폭 또한 미세화되면서 인터커넥션의 밀집정도가 증가하고 있다. 그로 인해 캐패시터 층과 전기전도층의 저항 차이로 인해 RC delay가 문제되고 있다. 이를 해결하기 위해서는 높은 전기전도도의 전극과 낮은 유전율의 유전체 개발이 요구된다. 본 연구에서는 PCB (Print Circuit Board)의 회로를 외부요인으로부터 보호하는 상용 PSR (photo solder resist)과 우수한 내열 및 저유전 특성을 보유한 PI (polyimide)를 혼합하여 저유전체 잉크 개발을 진행하였다. 그 결과 PSR과 PI를 10:3으로 혼합한 잉크가 가장 우수한 결과를 보였으며 20 GHz와 28 GHz에서 각각 유전 상수 약 2.6, 2.37을 보였고, 유전손실은 약 0.022, 0.016으로 측정되었다. 차후 어플리케이션 적용 가능성 검증을 위해 테프론에 제작된 다양한 선폭의 전송선로에 평가하였으며 그 결과, PSR만 사용했을 때보다 PI와 혼합한 저유전체 잉크를 사용한 전송선로의 손실이 S21에서 평균 0.12 dB 덜 감소한 결과를 보였다.

• 전기학회논문지
• /
• 제63권1호
• /
• pp.80-84
• /
• 2014

The discharge characteristics of Surface Dielectric Barrier Discharge (SDBD) reactor are investigated to find optimal driving condition with adjusting various parameter. When the high voltage with sine wave form is applied to SDBD source, successive pulsed current waveforms are observed owing to multiple ignitions through the long discharge channel and wall charge accumulation on the dielectric surface. The discharge voltage, total charge between dielectrics, mean energy and power are calculated from measured current and voltage according to electrode gap and dielectric thickness. Discharge mode transition from filamentary to diffusive glow is observed for narrow gap and high applied voltage case. However, when the diffusive discharge is occurred with high applied voltage, the actual firing voltage is always lower than that with low driving voltage. The $Si_3N_4$, $MgF_2$, $Al_2O_3$ and $TiO_2$ are considered for dielectric protection and high secondary electron emission coefficient. SDBD with $MgF_2$ shows the lowest breakdown voltage. $MgF_2$ thin film is proposed as a protection layer for low voltage atmospheric dielectric barrier discharge devices.

• Journal of information and communication convergence engineering
• /
• 제9권2호
• /
• pp.217-219
• /
• 2011

As silicon devices shrink and their density increases, the low dielectric constant materials instead of $SiO_2$ film is required. SiOC film as low-k films was deposited by the capacitively coupled plasma chemical vapor deposition and then annealed at $300{\sim}500^{\circ}C$ to find out the properties of the dependence on the temperature and polarity. This study researched the dielectric constant using by the structure of the metal/SiOC film/p-Si, chemical shift, thickness, refractive index and hardness. The trend of reflective index was inverse proportioned the thickness, but the dielectric constant was proportioned it. The dielectric constant decreased with decreasing the thickness and the increment of the refractive index.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권1호
• /
• pp.52-62
• /
• 2004

In this paper we look at the effect of Fringe-Enhanced-Barrier-lowering (FEBL) for high-K dielectric MOSFETs and the dependence of FEBL on various technological parameters (spacer dielectrics, overlap length, dielectric stack, S/D junction depth and dielectric thickness). We show that FEBL needs to be contained in order to maintain the performance advantage with scaled high-K dielectric MOSFETs. The degradation in high-K dielectric MOSFETs is also identified as due to the additional coupling between the drain-to-source that occurs through the gate insulator, when the gate dielectric constant is significantly higher than the silicon dielectric constant. The technology parameters required to minimize the coupling through the high-K dielectric are identified. It is also shown that gate dielectric stack with a low-K material as bottom layer (very thin $SiO_2$ or oxy-nitride) will be helpful in minimizing FEBL. The circuit performance issues with high-K MOS transistors are also analyzed in this paper. An optimum range of values for the dielectric constant has been identified from the delay and the energy dissipation point of view. The dependence of the optimum K for different technology generations has been discussed. Circuit models for the parasitic capacitances in high-K transistors, by incorporating the fringing effects, have been presented.

• 한국재료학회지
• /
• 제2권4호
• /
• pp.263-269
• /
• 1992

본 실험에서는 낮은 음의 온도계수를 갖는 저온 소결 유전체에 대해 연구하였다. 새로 개발된 재료의 조성은 Ti$O_2$(100-X) CuOx(X=1~5wt%)에 미량의 Mn$O_2$를 첨가 하였다. CuO를 첨가하지 않은 경우에는 저온 (90$0^{\circ}C$) 에서 소결이 진행되지 않았다. CuO 함량이 증가할수록 저온에서 소결이 가능하였으나, 유전율이 낮아지고 유전손실은 증가 하였다. Mn$O_2$를 0.6wt% 첨가한 경우 유전율과 Q값이 가장 높게 나타났다.

• 반도체디스플레이기술학회지
• /
• 제8권3호
• /
• pp.19-23
• /
• 2009

We have studied dielectric characteristics of low-k interlayer dielectric materials was fabricated by plasma enhanced chemical vapor deposition (PECVD). BTMSM precursor was introduced with the flow rates from 24 sccm to 32 sccm by 2 sccm step in the constant flow rate of 60 sccm $O_2$. Then, SiOCH thin film deposited at room temperature was annealed at temperature of $400^{\circ}C$ and $500^{\circ}C$ for 30 minutes in vacuum. The vibrational groups of SiOCH thin films were analyzed by FT/IR absorption lines, and the dielectric constant of the low-k SiOCH thin films were obtained by measuring C-V characteristic curves. With the result that FTIR analysis, as BTMSM flow rate increase, relative carbon content of SiOCH thin film increased from 29.5% to 32.2%, and increased by 32.8% in 26 sccm specimen after $500^{\circ}C$ annealing. Dielectric constant was lowest by 2.32 in 26 sccm specimen, and decreased more by 2.05 after $500^{\circ}C$ annealing. Also, leakage current is lowest by $8.7{\times}10^{-9}A/cm^2$ in this specimen. In the result, shift phenomenon of chemical bond appeared in SiOCH thin film that BTMSM flow rate is deposited by 26 sccms, and relative carbon content was highest in this specimen and dielectric constant also was lowest value

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.864-866
• /
• 2007

In PDP, bus electrode should have low resistance for high efficiency. The transparent dielectric affects the shape change of bus electrode during the firing. These are related with the electrical property of the electrode. In this study, the shape of electrode was controlled by firing schedules of the transparent dielectric and the bus electrode.

• 한국전기전자재료학회논문지
• /
• 제22권1호
• /
• pp.47-52
• /
• 2009

We studied the electrical characteristics of low-k SiOCH interlayer dielectric(ILD) films fabricated by plasma enhanced chemical vapor deposition (PECVD). BTMSM precursor was evaporated and introduced with the flow rates from 16 sccm to 25 sccm by 1 sccm step with the constant flow rate of 60 sccm $O_2$ in process chamber. The vibrational groups of SiOCH thin films were analyzed by FT!IR absorption lines, and the dielectric constant of the low-k SiOCH thin films were obtained by measuring C-V characteristic curves. The heat treatment on SiOCH thin films reduced the FTIR absorption intensity of the Si-O-$CH_3$ bonding group and Si-$CH_3$ bonding group but increased the intensity of Si-O-Si(C) bonding group. The SiOCH ILD films could have low dielectric constant $k\;{\simeq}\;2$ and also be reduced further by decreasing the $CH_3$ group density and increasing Si-O-Si(C) group density through annealing process.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권5호
• /
• pp.201-206
• /
• 2004

In order to investigate the optimum conditions for the effective ozone formation in a dielectric barrier discharge, measurements of ozone concentration were carried out for various conditions such as the gap length, the dielectric material and the operating gas. It was found that the optimum discharge conditions differed exceedingly in the types of operating gases and dielectric materials. In dry air, dielectric material with low dielectric constant and thermal conductivity, which might contribute to the restriction of the gas temperature rise in the discharge region, proved effective in obtaining both high ozone yield and concentration. The optimum gap length was considered to be in the range of 600-800 mm. In oxygen, using a quartz glass disk as a dielectric material, the required condition to obtain the high ozone yield and concentration was expanded.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권11호
• /
• pp.603-608
• /
• 2000

$(Ba, Sr)TiO_{3}$[BST] thin films were fabricated on the Pt/TiO$_2$/SiO$_2$/Si substrate by the RF sputtering. The structure and dielectric properties of the BST thin films with the substrate temperature were investigated. Increasing the substrate temperature, The BST phase increased and barium multi titanate phases decreased. Increasing the frequency, the dielectric constant decreased and the dielectric loss increased. The dielectric constant and dielectric loss of the BST thin films deposited at 50$0^{\circ}C$ were 300 and 0.018, respectively at 1 kHz. The leakage current density of the BST thin films deposited at 50$0^{\circ}C$ was $10^{-9}$ A/$\textrm{cm}^2$ with applied voltage of 3V. Because of the high dielectric constant(300), low dielectric loss(0.018) and low leakage current($10^{-9}$ A/$\textrm{cm}^2$), BST thin films deposited at 50$0^{\circ}C$ is expecting for the application of DRAM.