• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.1
• /
• pp.44-50
• /
• 2013

E-glass fiber is the most widely used glass fiber for reinforced composite materials of aircrafts, automobiles and leisure equipments. But recently researches are being progressed to reduce boric oxide from 8 % to 0 (zero), as is called 'Boron free E-glass', because of increasing material cost, environmental problem, and improving chemical resistance and mechanical properties of E-glass fiber. In this study, we fabricated the bulk glass and fiber glass of 'Boron free E-glass (BF) compositions', and characterized thermal properties and optical properties. 'Boron free E-glass (BF)' was obtained by the melting of mixed batch materials at $1550^{\circ}C$ for 2 hrs with different $Al_2O_3$ compositions 5~10 %. We obtained transparent clear glass with high visible light transmittance value of 81~86 %, and low thermal expansion coefficient of $4.2{\sim}4.9{\times}10^{-6}/^{\circ}C$ and softening point of $907{\sim}928^{\circ}C$. For the chemical resistance test of 'BF' fiber samples, we identified that the higher alumina contents gives the better corrosion resistance of glass fiber.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.262-263
• /
• 2001

저방출 코팅(low-e coating)이란 열 방출에 해당하는 적외선 파장이 가능한 작게 투과하도록 기판 위에 박막을 증착하는 방법이다. 그러므로 유리 기판 위에 저방출 코팅을 하는 것은 냉방시설을 갖춘 건축물 내부에서 에너지 절약과 쾌적한 환경을 구현하거나 자동차 내부의 빠른 온도상승을 저하시키는데 이용될 수 있다. 본 연구에서는 원격 조정 장치의 적외선 파장이 디스플레이의 광원에서 나올 수 있는 동일 파장에 의해 간섭을 받지 않도록 적외선 영역의 투과율은 낮추고 가시광선 영역의 투과율은 높이는 설계를 하고 최적화 하였다. (중략)

• KIEAE Journal
• /
• v.16 no.3
• /
• pp.121-128
• /
• 2016

Purpose: The vacuum glazing should constantly retain the gap in vacuum state to maintain high thermal performance. To do so, pillars are used to prevent the glazing from clinging to each other by the atmospheric pressure and therefore surface of the vacuum glazing is consistently affected by residual stress. The vacuum glazing could be applied to curtain wall systems at spandrel area to fulfill a rigorous domestic standard on U-value of the external wall. However, this can lead to high glazing temperature increase by heat concentration at a back panel and finally thermal stress breakage. This study experimentally determined weakness of the vacuum glazing systems on the thermal stress breakage and investigated effect of the residual stress. Method: The experiment first built two scale-down mock-up facilities that replicate the spandrel area in curtain wall, and then installed single low-e glass and vacuum glazing respectively. The two mock-up facilities were exposed to outside to induce the thermal stress breakage. Result: The experiment showed that the temperature occurred the thermal stress breakage was $114.4^{\circ}C$ for the single low-e glass and $118.9^{\circ}C$ for the vacuum glazing respectively. The result also showed the vacuum glazing reached the critical point earlier than the single low-e glass, which means that the vacuum glazing has high potential to occur the thermal shock breakage. In addition, the small temperature difference between two glazing indicates that the residual stress scarcely affects breakage of the vacuum glazing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.352-352
• /
• 2013

국내 에너지 소비량의 21.6%가 건물 분야에 소비되고 있다. 창호는 벽체에 비해 8~10배 이상 낮은 단열 특성을 가지기 때문에 열 손실량이 크다. 유리는 창호를 이루는 요소 중 가장 큰 면적을 차지하고 있으며, 창호의 단열성능을 2배로 향상시키면 30% 이상 건물의 에너지 절감 효과를 가질 수 있다. 창호의 단열 성능을 향상시키기 위해서 Low-e(emissivity) 기술 연구가 진행 중이다. 이번 실험에서는 RF 마그네트론 스퍼터링 시스템을 사용하여 XG 유리기판 위에 ZnO박막을 증착하고, evaporator 장비를 사용하여 metal층인 Ag를 증착하였다. 그리고 다시 한번 ZnO박막을 증착하였다. Low-e 연구에 활용할 수 있는지를 확인하기 위해 XRD, AFM, 투과도를 측정하였다. ZnO박막의 증착 조건은 초기압력 $3.0{\times}10^{-6}$ Torr, 공정압력 $2.0{\times}10^{-2}$ Torr, RF파워 30 W, Ar gas는 50 sccm, 증착온도는 상온으로 하였다. Metal층인 Ag를 증착하기 위해 evaporator의 증착 조건은 Rotate rate 2 rpm, voltage 0.3V, 공정압력 $5.0{\times}10^{-6}$ Torr이며, 변수로 Ag두께를 3,5,7,9,11,13,15 nm로 하였다. AFM 측정결과 Ag두께가 증가할수록 RMS roughness값이 높아졌으며, 최소 0.71 nm의 거칠기를 가지는 것을 확인하였다. XRD분석결과 37도 부근의 피크가 발생하여 ZnO 박막이 결정질 구조임을 확인할 수 있었다. 그리고 UV-Visible-NIR 분광 광도계를 이용하여 광학적 투과를 측정한 결과 Ag두께가 13 nm일 때 가시광 영역의 투과도가 최대 75%, 적외선 영역의 투과도가 최소 28%로 좋은 차단 특성을 가지는 것을 확인하였다. 위 결과들로 ZnO 박막이 Low-e 기술에 활용될 수 있음을 확인하였다.

• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.162-168
• /
• 2009

As a preliminary study of optimum composite properties under cryogenic temperature, the comparison of interfacial properties of carbon or glass fibers reinforced epoxy composites was evaluated at ambient and intermediate low temperature, i.e., 25 and $-10^{\circ}C$ by using micromechanical techniques. Under tensile and compressive loading conditions, their mechanical modulus at low temperature was higher than that atambient temperature. Interfacial shear strength (IFSS) at ambient and low temperatures was compared to each other, depending on epoxy matrix toughness and apparent modulus at the interface. The IFSS was much higher at low temperature than that at room temperature because of the increased epoxy matrix modulus. Statistical distributions of tensile strengths of glass and carbon fibers were evaluated for different temperature ranges, which is dependent upon fiber's inherent flaws and rigidity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.340.1-340.1
• /
• 2014

본 실험에서는 Ag두께 변화에 따른 투과율과 Energy bandgap의 변화를 알아보기 위해 RF Sputter장비와 Evaporator장비를 사용하여 IGZO, ZnO, AZO OMO 구조로 Low-e 코팅된 Glass를 제작하였다. $3cm{\times}3cm$의 Corning1737 유리기판에 RF Sputtering 방식으로 Oxide layer를 증착 하였고 Evaporator장비로는 Metal layer인 Ag막을 증착하였다. Oxide layer 증착 시 RF Sputter장비의 조건은 $3.0{\times}10^{-6}Torr$이하로 하였으며, 증착압력은 $6.0{\times}10^{-3}Torr$, 증착온도는 실온으로 고정하였다. Metal layer 증착 시 Evaporator장비의 조건은 $5.0{\times}10^{-6}Torr$이하, 전압은 0.3 V, Rotate 2 rpm으로 고정하였다. 실험 변수로는 Ag 두께를 5,7,9,11,13 nm로 변화를 주어 실험을 진행하였다. 투과도 측정 장비를 사용하여 각 샘플을 측정한 결과 IGZO의 경우 가시광영역의 평균 투과율이 80% 이상이며 Ag두께가 5nm일 때부터 자외선 영역의 빛을 차단하여 low-e 특성을 나타내었다. 이는 산화물인 IGZO가 결정질인 AZO, ZnO 보다 낮은 표면거칠기를 가지기 때문이다. Ag 두께에 따른 각 물질의 Optical energy bandgap 분석결과 Ag 두께가 증가할수록 IGZO는 4.65~4.5 eV, AZO는 4.6~4.4 eV, ZnO는 4.55~4.45 eV로 Energy bandgap은 감소하였다. AFM장비를 이용하여 각 샘플의 표면 Roughness 측정 결과 Ag 두께가 증가할수록 표면거칠기도 증가하는 경향을 나타내었다.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.95-102
• /
• 2011

The purpose of study is to estimate heating, cooling load performance and economic efficiency in office building with applied the functional paint. this paint can reduced SHGC(Solar Heat Gain Coefficient) on the glazing surface by coating. In this study, estimated to compared with double glazing, low-e glazing, IP(Insulation Paint) and IPu(Insulation UV-Cut Paint) coating glazing. As a result of this study, 1)heating & cooling load Analysis, SHGC value and U-factor of double glazing is about 0.70 and 3.29($W/m^2K$). low-E glazing is about 0.65 and 2.70($W/m^2K$). Two-side it is about 0.27 and 3.25($W/m^2K$). When compared to double glazing, annual heating & cooling load of low-E glazing, Two-side IPu and IP paint coating glazing is 3,012MWh($124kWh/m^2$), 2,910MWh($120kWh/m^2$), 2,867MWh($118.4kWh/m^2$) and 2,867MWh($118.4kWh/m^2$). It i sreduced to 2.0%, 5.2%, 6.7%, and 6.7% respectively. 2)the estimation of economic efficiency, low-e glazing installed in office building can not recover the investment within a lifetime 40years. but IPu and IP paint, two-side coating in glazing, have a payback period of 13 years respectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.82-83
• /
• 2003

일반적인 PDP (Plasma display panel)용 전도성 저방출(low-e) 필터는 유리 기판 위에 굴절률이 높은 금속 산화물 유전체 박막과 Ag와 같은 귀금속 박막이 번갈아 쌓인 [유전체｜금속(Ag)｜유전체]가 기본 구조인 다층 박막의 형태로 개발되어 왔다. Ag는 가시광선 영역에서 다른 금속보다 작은 흡수를 보이고 전도성이 뛰어나 전자파 차페용 필터의 전도성 박막으로 널리 쓰인다. 그리고 이러한 구조에서 가시광선의 높은 투과율을 유지하면서 유해 전자기파를 차폐할 수 있도록 충분한 전도성을 갖추기 위해서는 2층 이상의 Ag 박막이 존재하도록 설계되며 유전체 박막과 금속 박막 사이에 1∼2 nm 정도의 매우 얇은 금속 보호 층을 사용한다. (중략)

• Horticultural Science & Technology
• /
• v.28 no.3
• /
• pp.387-393
• /
• 2010

The free sugar content and related enzymes of four different parts, inner, outer, stylar end and stem end, of 'Changhowon Hwangdo' peach ($Prunus$ $persica$, L. Batsch) fruit were compared from August to September in 2006, i.e., from 120 to 150 days after full bloom (DAFB). The soluble solids content (SSC) of stylar end was the highest among the four fruit parts at 150 DAFB. Changes of free sugar content were similar to that of SSC in the four parts. The starch content at the stylar end was the highest at 120 DAFB, while all the other parts showed low starch contents at 150 DAFB. The free sugar composition of peach changed during fruit development. The sucrose was low at 120 DAFB and increased gradually in all parts of peach fruit. On the contrary glucose, fructose and sorbitol decreased with fruit development. The free sugar contents and related enzymes activities were investigated during fruit development. The rapid increase of sucrose contents during fruit development was more affected by sucrose synthase than sucrose phosphate synthase. Activity of SS in the four fruit parts increased continuously over the fruit development period, but activity of acid invertase showed a downward trend. This study found that the free sugar content was affected by enzyme activity for the synthesis or the cleavage. However, it was very difficult to explain sugar accumulation of peach segments with related-enzymes.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.28-32
• /
• 2010

Technical demands for aspheric glass lens formed in market increases its application from simple camera lens module to fiber optics connection module in optical engineering. WC is often used as a metal core of the aspheric glass lens, but the long life time is issued because it fabricated in high temperature and high pressure environment. High hard thin film coating of lens core increases the core life time critically. Diamond Like Carbon(DLC) thin film coating shows very high hardness and low surface roughness, i.e. low friction between a glass lens and a metal core, and thus draw interests from an optical manufacturing industry. In addition, DLC thin film coating can removed by etching process and deposit the film again, which makes the core renewable. In this study, DLC films were deposited on the SiC ceramic core. The process variable in FVA(Filtered Vacuum Arc) method was the substrate bias-voltage. Deposited thin film was evaluated by raman spectroscopy, AFM and nano indenter and measured its crystal structure, surface roughness, and hardness. After applying optimum thin film condition, the life time and crystal structure transition of DLC thin film was monitored.