• International Journal of Safety
• /
• 제1권1호
• /
• pp.58-61
• /
• 2002

A preparation method of cobalt supported alumina catalyst for a emergency escape mask cartridge has been studied. Catalysts were prepared by incipient wetness impregnation method using pre-shaped $\gamma$=alumina powders of 70-100 mesh. The catalyst was tested in a continuous-flow reactor system and characterized by elemental analysis, BET and TGA-DTA techniques. Cobalt shows higher activity than platinum or nickel for carbon monoxide oxidation at room temperature. Optimum loading amount of cobalt was 10 wt.% for CO oxidation and the reaction activity increases gradually with the increase of calcination temperature up to $450^{\circ}C.

• 한국대기환경학회지
• /
• 제6권1호
• /
• pp.57-72
• /
• 1990

The oxidation of carbon monoxide on a catalyst, $LaSrNiCoO_3$ was investigatigated with a plug flow system. Kinetic quantities such as reaction-rate, reaction order and Arhenius-parameters at various reactor temperature from 200$^\circ$C to 300$^\circ$C were determined. Also, the optimum condition for the oxidation of carbon monoxide with this catalyst was determined and are as follows. Partial pressure of oxigen ; 428mmHg Partial pressure of carbon monoxide ; 332mmHg Mixed moral ratio of oxigen and Carbon monoxide ; 1.3 : 1 Total gas flow ; 224ml/min Reaction temperature ; 340$^\circ$C The reaction kinetic equation at the optimum condition, temperature range from 200$^\circ$C to 340$^\circ$C, are as follow. $$ $v = Ae^{6.5Kcal/RT} [CO]^{0.93 \sim 0.98} [O_2]^{0.42 \sim 0.50}$ $$ In addition to this, numerical calculation were performed to evaluate the mass and heat transfer effect on this system.

• 한국환경과학회지
• /
• 제26권11호
• /
• pp.1201-1208
• /
• 2017

Oxidative degradation of chlorinated ethenes was carried out using heat-activated persulfate. The activation rate of persulfate was dependent on the temperature and the activation reaction rate could be explained based on the Arrhenius equation. The activation energy of persulfate was 19.3 kcal/mol under the assumption that the reaction between the sulfate radical and tricholoroethene (TCE) is very fast. Activation could be achieved at a moderate temperature, so that the adverse effects due to high temperature in the soil environment were mitigated. The reaction rate of TCE was directly proportional to the concentration of persulfate, indicating that the remediation rate can be controlled by the concentration of the injected persulfate. The solution was acidized after the oxidation, and this was dependent on the oxidation temperature. The consumption rate of persulfate was high in the presence of the target organic, but the self-decomposition rate became very low as the target was completely removed.

• 한국응용과학기술학회지
• /
• 제22권1호
• /
• pp.56-61
• /
• 2005

Methanol was synthesized by homogeneous and catalytic reactions of partial oxidation of methane. The effect of pressure, temperature and oxygen concentration on methanol synthesis was investigated. The catalyst used was Bi-Cs-Mg-Cu-Mo mixed oxide. The partial oxidation reaction was carried out in a fixed bed reactor at 20${\sim}$46 bar and $450{\sim}480^{\circ}C$ and oxygen concentration of 5.3${\sim}$7.7mol%. The results were compared with results of homogeneous reaction performed at the same conditions. Methane conversions of the homogeneous and catalytic reactions increased with temperature. Methanol selectivity of the homogeneous reaction decreased with increasing temperature. However, the methanol selectivity of catalytic reaction increased with temperature. For both homogeneous and catalytic reactions, the methane conversions were around 5%. This may be due to the low oxygen concentration. Methanol selectivity of the catalytic reaction was higher than that of homogeneous one.

• 한국수소및신에너지학회논문집
• /
• 제23권2호
• /
• pp.173-182
• /
• 2012

Effects of temperature, pressure, and gas residence time on methane combustion characteristics of mass produced oxygen carrier particle (OCN706-1100) were investigated in a pressurized fluidized bed reactor using methane and air as reactants for reduction and oxidation, respectively. The oxygen carrier showed high fuel conversion, high $CO_2$ selectivity, and low CO concentration at reduction condition and very low NO emission at oxidation condition. Moreover OCN706-1100 particle showed good regeneration ability during successive reduction-oxidation cyclic tests up to the 10th cycle. Fuel conversion and $CO_2$ selectivity decreased and CO emission increased as temperature increased. These results can be explained by trend of calculated equilibrium CO concentration. However, $CO_2$ selectivity increased as pressure increased and fuel conversion increased as gas residence time increased.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1998년도 한국재료학회 춘계학술발표강연 및 논문개요집
• /
• pp.10-10
• /
• 1998

• Bulletin of the Korean Chemical Society
• /
• 제16권3호
• /
• pp.296-298
• /
• 1995

• 한국환경과학회지
• /
• 제18권10호
• /
• pp.1071-1077
• /
• 2009

A novel pretreatment technique was applied to the conventional Pt/alumina catalyst to prepare for the highly efficient catalyst for the preferential oxidation of carbon monoxide in hydrogen-rich condition. Their performance was investigated by selective CO oxidation reaction. CO conversion with the oxygen-treated Pt/Alumina catalyst increased remarkably especially at the low temperature below $100^{\circ}C$. This result is promising for the normal operation of the proton exchange membrane fuel cell (PEMFC) without CO poisoning of the anode catalyst. XRD analysis results showed that metallic Pt peaks were not observed for the oxygen-treated catalyst. This implies that well dispersed small Pt particles exist on the catalyst. This result was continued by high resolution transmission electron microscopy (HRTEM) analysis. Consequently, it can be concluded that highly dispersed Pt nanoparticles could be prepared by the novel pretreatment technique and thus, CO conversion could be increased considerably especially at the low temperatures below $100^{\circ}C$.

• 한국응용과학기술학회지
• /
• 제31권2호
• /
• pp.313-319
• /
• 2014

This study was performed to obtain high conversion efficiency of $NH_3$ and minimize generation of nitrogen oxides using metal-supported catalyst with Ag : Cu ratio. Through structural analysis of the prepared catalyst with Ag : Cu ratio ((10-x)Ag-xCu ($0{\leq}x{\leq}6$)), it was confirmed that the specific surface area was decrease with increasing metal content. A prepared catalysts showed Type II adsorption isotherms regardless of the ratio Ag : Cu of metal content, and crystalline phase of $Ag_2O$, CuO and $CuAl_2O$ was observed by XRD analysis. In the low temperature($150{\sim}200^{\circ}C$), a conversion efficiency of AC_10 recorded the highest(98%), whereas AC_5 (Ag : Cu = 5 : 5) also showed good conversion efficiency(93.8%). However, in the high temperature range, the amounts of by-products(NO, $NO_2$) formed with AC_5 was lower than that of AC_10. From these results, It is concluded that AC_5 is more environmentally and economically suitable.

• 대한전자공학회논문지SD
• /
• 제40권8호
• /
• pp.560-564
• /
• 2003

본 논문에서는 RTP(rapid thermal process)를 이용한 새로운 산화방법을 고안했으며, 이는 짧은 시간에 다공질 실리콘을 산화시킴으로써 이 기술은 여타 방법에 비해 경제적이고 간편한 방법으로 짧은 시간에 두꺼운 산화막을 성장시킬 수 있는 장점을 가지고 있다. 먼저, 양극반응을 통해 PSL(porous silicon layer)을 형성한 후 이를 저온 산화시킨 후에 급속 열처리 산화공정(RTO: rapid thermal oxidation)를 이용해서 OPSL(oxidized porous silicon layer)을 제조하고, 그 물성 및 전기적 특성을 조사하여, 열 산화로 제작된 OPSL과 그 특성을 비교하였다. 시편의 절연 파괴전압은 약 3.9 MV/cm의 값을 보여 벌크 산화막보다는 적은 값이지만 절연 재료로서는 충분한 값이고, 누설전류는 0 ∼ 50 V의 인가 전압에서 100 ∼ 500 ㎀의 값을 보였다. 그리고, XPS 결과는 RTO 공정 추가가 저온 산화막의 완전 산화에 크게 기여함을 확인하였으며, 저온 산화막의 표면 및 내부에서도 산화반응이 완전하게 이루어졌음을 확인하였다. 이 결과로부터 저온 OPSL을 제조할 때, RTO 공정이 OPSL의 산화 및 치밀화(densification)의 증가에 크게 기여함을 알 수 있었다. 따라서, 이의 방법으로 제조된 OPSL은 저온을 요구하는 공정에서 소자의 절연막, 전기적인 분리층 그리고 실리콘 고주파용 기판 등으로 활용될 수 있을 것으로 보인다.