• Journal of Korean Society for Atmospheric Environment
• /
• 제19권E3호
• /
• pp.121-127
• /
• 2003

The characteristics of heterogeneous photocatalytic decomposition were investigated at low concentration level of $O_3$on TiO$_2$for various operating parameters such as: loaded catalyst weight (0∼4 mg/$\textrm{cm}^2$), initial concentration of $O_3$(0.06∼10.0 ppm), gas flow rate (1.0 ∼ 2.5ι/min), and relative humidity (0∼80%). This study was conducted using a flow-type reactor at room temperature. Three kinds of pure TiO$_2$(P25, ST -01, and E- 23) were employed as photocatalyts. It was found that $O_3$removal ratio was identical, regardless of the loaded TiO$_2$weight in the range from 0.5 to 4.0 mg/$\textrm{cm}^2$. It was also found that higher initial ozone concentration results in greater oxidation rate of ozone and experimental data show kinetically a good agreement with Langmur-Hinshelwood kinetic model. We also observed that the removal ratio of $O_3$increases linearly with the increasing flow rate and also with the increasing relative humidity for each catalyst.

• Applied Microscopy
• /
• 제33권1호
• /
• pp.17-23
• /
• 2003

습식 산화 분위기에서 vapor-solid process를 통해 금속 촉매를 사용하지 않고도 낮은 온도에서 산화 인듐나노선을 성공적으로 합성하였다. 나노선은 x-선 회절(XRD), 분산 x-선 분광 분석기(EDS)를 갖춘 주사전자현미경(SEM), 투과전자현미경(TEM)을 통해 분석되었다. XRD 결과는 합성된 산화 인듐 나노선이 입방정 구조를 갖는다는 것을 보여준다. 이러한 나노선들은 두 가지 형태를 갖는다. 하나는 줄기에 약 500 nm 크기의 각진 나노입자가 형성된 형태이고 다른 하나는 나노입자가 형성되지 않은 형태이다. 나노선의 길이는 수 마이크로미터 범위이고, 두께는 약 10 nm에서 250 nm 범위이다. 나노선은 결함을 포함하지 않았으며 표면에 5 nm 이하의 비정질 층을 가지고 있었다. TEM 분석 결과 대부분의 나노선의 성장 방향은 <100> 방향이었으나 나노입자를 포함한 나노선은 <110> 방향으로 자랐다는 것이 발견되었다. 이러한 성장 방향은 이전의 문헌에서 보고되지 않은 새로운 결과이다. 일반적인 성장 방향과는 다른 새로운 방향으로 나노선이 자랄 수 있었던 것은 본 연구에서 산화물 합성 시 산소의 공급원으로 사용된 습식 분위기와 비교적 낮은 온도가 원인인 것으로 생각된다. 따라서 습식 산화 분위기에서의 나노선 합성법을 다른 여러 산화물의 나노선 합성에 응용한다면 낮은 온도에서 새로운 형태 및 성장 방향을 갖는 나노선을 얻을 수 있을 것으로 예상된다.

• 한국재료학회지
• /
• 제23권12호
• /
• pp.708-713
• /
• 2013

Graphene oxide has been synthesized by microwave-assisted exfoliation of graphite oxide prepared by modified Hummers method. Graphite was oxidized in a solution of $H_2O_2$ and $KMnO_4$ at $65{\sim}80^{\circ}C$, followed by 10 % $H_2O_2$ solution treatment at $80{\sim}90^{\circ}C$. The graphite oxide was exfoliated under microwave irradiation of 1 kW and was reduced to graphene effectively by hydrazine hydrate ($H_4N_2{\cdot}H_2O$) treatment. The exfoliation of graphene oxide was significantly affected by the microwave irradiation on (heating)/off (cooling) period. An on/off period of 10 s/20 s resulted in much more effective exfoliation than that of 5 s/10 s with the same total treatment time of 10 min. This can be explained by the higher exfoliation temperature of 10 s/20 s. Repetition of the graphite oxidation and exfoliation processes also enhanced the exfoliation of graphene oxide. The thickness of the final graphene products was estimated to be several layers. The D band peaks of the Raman spectra of the final graphene products were quite low, suggesting a high crystal quality.

• Applied Science and Convergence Technology
• /
• 제25권1호
• /
• pp.19-24
• /
• 2016

In this study, we evaluated the change of electronic structure during redox process in cerium-doped $ZrO_2$ grown by sol gel method. By sol-gel method, we could obtain cerium-doped $ZrO_2$ in high oxygen partial pressure and low temperature. After post annealing process in nitrogen ambient, the film is deoxidized. We used spectroscopic and theoretical methods to analysis change of electronic structure. X-ray absorption spectroscopy (XAS) for O K1-edge and Density Functional Theory (DFT) calculation using VASP code were performed to verify the electronic structure of the film. Also, high resolution x-ray photoelectron spectroscopy (HRXPS) for Ce 3d was carried out to confirm chemical bond of cerium doped $ZrO_2$. Through the investigation of the electronic structure, we verified as followings. (1) During reduction process, binding energy of oxygen is increase. Simultaneously, oxidation state of cerium was change to 4+ to 3+. (2) Cerium 4+ and cerium 3+ states were generated at different energy level. (3) Absorption states in O K edge were mainly originated by Ce 4+ $f_0$ and Ce 3+, while occupied states in valance band were mainly originated from Ce 4+ $f_2$.

• Restorative Dentistry and Endodontics
• /
• 제18권2호
• /
• pp.431-445
• /
• 1993

The purpose of this study was to observe corrosion characteristics of six dental amalgams and was to analyse corrosion products electrochemically. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by using mechanical amalgamator, the triturated mass was inserted into the cylinderical metal mold ($12{\times}10mm$) and was condensed with 160kg/$cm^2$ by using the hydrolic press. The specimen was removed from the mold and was stored at room temperature for 1 week, and was polished with amalgam polishing kit. The anodic and cathodic polarization curve was obtained by using cyclic voltammetric method with 3-electrode potentiostat in saline for each amalgam and Ag, Sn, Cu plate specimen at $37{\pm}0.5^{\circ}C$. The potential sweep range was -1.7V~0. 4V(vs SCE) in working electrode and scan rate was 50mV/s and the exposed surface area of each specimen to the electrolytic solution was $0.79cm^2$. The results were as follows. 1. In anodic-cathodic polarization curve of amalgam specimens, two anodic current rising areas and two cathodic current peaks were obtained at the low Cu amalgam(CF, CS) specimen and three anodic current rising areas and three cathodic current peaks were obtained at the high Cu amalgam (TY, DS, HV) specimen. 2. As this compared with the anodic and cathodic current peak potentials of Sn, Cu and Ag specimen, the first cathodic current peak I c was caused by the reduction of divalent tin salt, second cathodic current peak IIIc results from the reduction of quadravalent tin salt, and third cathodic current peak me results from the reduction of copper salt. 3. As reverse potential sweeping was done repeatedly, anodic current was decreased slightly in all amalgam specimens.

• 폴리머
• /
• 제35권5호
• /
• pp.444-450
• /
• 2011

천연 알지네이트를 저분자화시키기 위해 과산화수소/초음파를 사용하였다. 이때 반응 온도 시간, 과산화수소 농도 그리고 초음파 조사 조건 등이 저분자화 생성물에 미치는 영향을 검토하였다. 생성된 저분자 알지네이트의 화학적 구조를 규명한 결과 주로 1,4-glycosidic bond가 끓어져서 저분자화가 진행되고 특정조건에서 생성물에 formate 그룹이 형성됨을 확인할 수 있었다. 생성물의 분자량은 MALS가 부착된 GPC를 사용하여 측정하였다. 2 wt%의 고분자 알지네이트 용액을 50 $^{\circ}C$의 초음파 분위기에서 0.5시간 동안 반응시켰을 때 분자량이 450 kDa에서 15.9 kDa로 저하되었다. 또한 분자량분포도는 상당히 좁고 반응 조건에 따라 큰 변화 없이 일정함(~2)을 확인할 수 있었다.

• 한국분무공학회지
• /
• 제21권3호
• /
• pp.130-136
• /
• 2016

NOx and PM are important air pollutants as vehicle management policy aspect. Medium-duty truck is the main source of the pollutants although the vehicle market share is only 3.5%. National emission portion of NOx and PM form the mobile sourece are 14% and 16% respectively. In this study it was investigated that characteristics of air pollutants emission on medium duty truck equipped with EGR and SCR system. Vehicle's test reflected driving cycle on the chassis dynamometer, and applied test cycle was WHVC(World Harmonized Vehicle Cycle) mode. The test cycle include three segments, represent urban, rural and motorway driving. Based on the test results NOx, PM, HC were less emitted form SCR vehicle than EGR vehicle. And CO was less emitted form EGR vehicle than SCR vehicle due to CO oxidation reaction on DPF surface. And most air pollutants reduced as average vehicle speed increased. Pollutants were less emitted on motorway section than urban and rural sections. But highly NOx emission on motorway section was verified according to increased EGR ratio on fast vehicle speed. HC and CO additional emission was identified as 68%, 58% respectively during SCR vehicle's cold engine start emission test. NOx additional emission was detected by 24% on SCR vehicle's condition of engine cold start while not detected on vehicle equipped with EGR. SCR vehicle's additional NOx emission was derived from low reaction temperature during engine cold start condition. medium-duty truck emission characteristics were investigated in this study and expected to used to improve air pollutants management policy of medium-duty truck equipped with SCR & EGR.

• 한국환경과학회지
• /
• 제16권7호
• /
• pp.785-791
• /
• 2007

The current study evaluated the technical feasibility of the application of titanium dioxide ($TiO_{2}$) photo-catalytic air cleaners for the disinfection of bioaerosols present in indoor air. The evaluation included both laboratory and field tests and the tests of hydraulic diameter (HD) and lamp type (LT). Disinfection efficiency of photocatalytic oxidation (PCO) technique was estimated by survival ratio of bacteria or fungi calculated from the number of viable cells which form colonies on the nutrient agar plates. It was suggested that the reactor coating with $TiO_{2}$ did not enhance the adsorption of bioaerosols, and that the UV irradiation has certain extent of disinfection efficiency. The disinfection efficiency increased as HD decreased, most likely due to the decrease in the light intensity since the distance of the catalyst from the light source increased when increasing the HD. It was further suggested that the mass transfer effects were not as important as the light intensity effects on the PCO disinfection efficiency of bioaerosols. Germicidal lamp was superior to the black lamp for the disinfection of airborne bacteria and fungi, which is supported by the finding that the disinfection efficiencies were higher when the germicidal lamp was used compared to the black lamp in the laboratory test. These findings, combined with operational attributes such as a low pressure drop across the reactor and ambient temperature operation, can make the PCO reactor a possible tool in the effort to improve indoor bioaerosol levels.

• 청정기술
• /
• 제20권4호
• /
• pp.367-374
• /
• 2014

0.1~1 M의 철킬레이트 화합물을 이용한 화학흡수반응에 의한 바이오가스내 황화수소제거를 위한 실험이 수행되었다. 철킬레이트 화합물을 이용한 황화수소제거는 철킬레이트의 최적산화반응을 통해 이루어진다. 바이오가스에 존재하는 황화수소는 킬레이트농도 및 pH 등의 공정조건에 따라 효과적으로 제거될 뿐만 아니라 철킬레이트 산화반응에 의해 황화수소내 존재하는 황성분을 생성시킨다. Fe-EDTA의 농도가 증가하면 철킬레이트 화합물의 착물이 안정되어 황생성의 전환이 증가하였다. 또한 철킬레이트화합물의 안정도는 pH에 따라 변하는 중요한 인자이고 pH 9에서 최적반응을 나타냈다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2181-2185
• /
• 2008

Fuel processing systems which convert HC fuel into $H_2$ rich gas (such as stream reforming, partial oxidation, auto-thermal reforming) need high temperature environment($600-1000^{\circ}C$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1-5kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural & anode off gas as reformer fuel. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity.