• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.322-322
• /
• 2010

For boron doping on n-type silicon wafer, around $1,000^{\circ}C$ doping temperature is required, because of the relatively low solubility of boron in a crystalline silicon comparing to the phosphorus case. Boron doping by fiber laser annealing and lamp furnace heat treatment were carried out for the uniformly deposited p-a-Si:H layer. Since the uniformly deposited p-a-Si:H layer by cluster is highly needed to be doped with high temperature heat treatment. Amorphous silicon layer absorption range for fiber laser did not match well to be directly annealed. To improve the annealing effect, we introduce additional lamp furnace heat treatment. For p-a-Si:H layer with the ratio of $SiH_4:B_2H_6:H_2$=30:30:120, at $200^{\circ}C$, 50 W power, 0.2 Torr for 30 min. $20\;mm\;{\times}\;20\;mm$ size fiber laser cut wafers were activated by Q-switched fiber laser (1,064 nm) with different sets of power levels and periods, and for the lamp furnace annealing, $980^{\circ}C$ for 30 min heat treatment were implemented. To make the sheet resistance expectable and uniform as important processes for the $p^+$ layer on a polished n-type silicon wafer of (100) plane, the Q-switched fiber laser used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the fiber laser treatment showed the trade-offs between the lifetime and the sheet resistance as $100\;{\omega}/sq.$ and $11.8\;{\mu}s$ vs. $17\;{\omega}/sq.$ and $8.2\;{\mu}s$. Diode level device was made to confirm the electrical properties of these experimental results by measuring C-V(-F), I-V(-T) characteristics. Uniform and expectable boron heavy doped layers by fiber laser and lamp furnace are not only basic and essential conditions for the n-type crystalline silicon solar cell fabrication processes, but also the controllable doping concentration and depth can be established according to the deposition conditions of layers.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1422-1425
• /
• 2018

$NaTa_{1-x}Fe_xO_3$ ($0{\leq}x{\leq}0.40$) nanocubes were synthesized by a relatively low temperature hydrothermal method, using $Ta_2O_5$, $FeCl_3$ and NaOH as the precursors. The UV-vis diffuse reflectance spectra showed that $NaTa_{1-x}Fe_xO_3$ had significant visible-light-absorbing capability, and the absorption edge of $NaTaO_3$ shifted to longer wavelength with the increase of Fe dopants. Moreover, $NaTa_{1-x}Fe_xO_3$ exhibited room-temperature ferromagnetism when $Fe^{3+}$ occupied $Ta^{5+}$ sites in $NaTaO_3$ crystal lattice. The ferromagnetism is mainly attributed to the superexchange interactions between doped $Fe^{3+}$, rather than the contribution of oxygen vacancies caused by Fe doping. Therefore, Fe doping can simultaneously regulate the optical and magnetic properties of $NaTaO_3$ semiconductor, which will enable its potential applications in multifunctional optical-electronics and opticalspintronics devices.

• 보존과학회지
• /
• 제38권4호
• /
• pp.301-313
• /
• 2022

We made a Korean white porcelain or Joseon Baekja jar and based on the raw materials used and reproductions of each stage, we aimed to compare and analyze the physicochemical changes of the raw materials such as clay at each manufacturing stage, as well as identify the characteristics and correlations. Although the basic main components of clay and glaze material are similar, their texture becomes denser in the process of bisque firing pottery (Chobeol-pyeon) and glaze firing pottery (Jaebeol-pyeon), and we confirmed that in addition to the tendency of increasing vitrification, low-temperature minerals such as mica and illite gradually disappeared, while high-temperature minerals such as cristobalite were newly created. This phenomenon has also been verified by the rapid decrease in absorption rate while the change in specific gravity was small. In addition, the color was greatly affected by the firing atmosphere, and the yellow-red chromaticity of the raw materials was higher during bisque firing but showed a rapidly decreasing characteristic during glaze firing. The value of magnetic susceptibility, which is related to iron (Fe) component, showed a tendency to decrease in glaze firing pottery. CT images were confirmed as a method that can indirectly estimate the change in the material properties of the object step-by-step for the entire object. In conclusion, the study of manufacturing stages of reproduction can provide basic data for scientific research on the estimation of porcelain and pottery making technology and changes in raw materials.

• 한국초전도ㆍ저온공학회논문지
• /
• 제25권2호
• /
• pp.5-9
• /
• 2023

The effect of La_0.7Sr_0.3MnO₃ (LSMO) addition on the superconducting property of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ ((Bi, Pb)-2223) polycrystalline samples was studied. LSMO (0.3 wt.% to 2.0 wt.%) added (Bi, Pb)-2223 samples were prepared by using a solid-state reaction method. The XRD analyses show that as the LSMO addition increases, the volume fraction of the Bi-2223 phase is gradually decreased. The critical temperature (T_c) exhibits a gradual decrease with a single transition as the LSMO amount increases up to 1.0 wt.%, but a further addition of LSMO induces an abrupt decrease of T_c with a dual transition. The analyses on the local structure of the CuO₂ plane from the X-ray absorption fine structure (EXAFS) measurements showed that for the samples with low concentration of LSMO up to 1.0 wt.%, the Cu-O bond length and the CuO₂ plane ordering do not degrade from the values of pure (Bi, Pb)-2223, while they get worsen with a further increase of LSMO addition. These results open up the possibility of LSMO as artificial pinning centers of the (Bi, Pb)-2223 system for power application.

• 대한화학회지
• /
• 제39권3호
• /
• pp.204-212
• /
• 1995

매트릭스 개선제를 이용하여 물시료중 흔적량 납의 흑연로 원자흡수 분광분석에 관하여 검토하였다. 이 때 시료의 매트릭스를 개선시킬 수 있는 개선제의 종류를 찾고 그것의 사용량을 최적화시켰다. 쉽게 휘발하는 성질을 가진 납은 개선제가 없으면 희화 및 원자화 온도가 많이 낮으며 측정되는 흡광도도 낮고, 재현성도 좋지 않다. 따라서 개선제를 사용할 필요가 있는데, 납 50 ${\mu}g/mL$ 용액에 팔라듐을 5 ng/mL되게 첨가하면 희화온도를 400$^{\circ}C$에서 1,000$^{\circ}C$로, 원자화 온도를 1800$^{\circ}C$에서 2,000$^{\circ}C$로 증가시킬 수 있었다. 또, 보조 개선제로 알루미늄을 1.5 ${\mu}g/mL$ 혼합하여 사용하면 희화온도를 150$^{\circ}C$ 더 증가시킬 수 있다. 개선제로 팔라듐을 사용했을 경우가 개선제를 사용하지 않았을 경우보다 감도를 5배 이상 증가시킬 수 있었고, 상대 표준편차도 5% 이내가 될 정도로 좋은 재현성을 나타내었다. 그리고 본 실험방법의 유용성을 알아보기 위하여 학교 폐수와 파이프 세정 작업중의 수돗물을 실제 시료로 선택하여 정량하였는데 재현성이 좋은 결과를 얻었고. 이들 시료에 일정량의 납을 첨가하여 회수율을 얻었는데 89% 이상으로 정량적이었다.

• Transactions on Electrical and Electronic Materials
• /
• 제1권1호
• /
• pp.26-31
• /
• 2000

The ~1540 nm $^4$ $I_{13}$ 2/ longrightarro $w^4$ $I_{15}$ 2/ emissions of E $r^{3+}$ in Er-implanted GaN annealed at temperatures in the 400 to 100$0^{\circ}C$ range were investigated to gain a better understanding of the formation and dissociation processes of the various E $r^{3+}$ sites and the recovery of damage caused by the implantation with increasing annealing temperature ( $T_{A}$).The monotonic increase in the intensity of the broad defect photoluminescence(PL) bands with incresing $T_{A}$ proves that these are stable radiative recombination centers introduced by the implantation and annealing process. Theser centers cannot be attributed to implantation-induced damage that is removed by post-implantation annealing. Selective wavelength pumpling of PL spectra at 6K reveals the existence of at least nine different E $r^{3+}$ sites in this Er-implanted semiconductor. Most pf these E $r^{3+}$ PL centers are attributed to complexed of Er atoms with defects and impurities which are thermally activated at different $T_{A}$. Only one of the nine observed E $r^{3+}$ PL centers can be pumped by direct 4f absorption and this indicates that it is highest concentration E $r^{3+}$ center and it represents most of the optically active E $r^{3+}$ in the implanted sample. The fact that this E $r^{3+}$ center cannot be strongly pumped by above-gap light or broad band below-gap absorption indicates that it is an isolated center, i.e not complexed with defects or impurities, The 4f-pumped P: spectrum appears at annealing temperatures as low as 40$0^{\circ}C$, and although its intensity increase monotonically with increasing $T_{A}$ the wavelengths and linewidths of its characteristic peaks asre unaltered. The observation of this high quality E $r_{3+}$PL spectrum at low annealing temperatures illustrates that the crystalline structure of GaN is not rendered amorphous by the ion implantation. The increase of the PL intensities of the various E $R_{3+}$sites with increasing $T_{A}$is due to the removal of competing nonradiative channels with annealing. with annealing.annealing.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.612-619
• /
• 2002

The dynamic behavior of Al-Mg alloys plasma was very unstable and this instability was closely related to the unstable motion of keyhole during laser irradiation. The keyhole fluctuated both in size and shape and its fluctuation period was about 440 ${\mu}{\textrm}{m}$. This instability has been estimated to be caused by the evaporation phenomena of metals with different boiling point and latent heats of vaporization. Therefore, the authors have conducted the spectroscopic diagnostics of plasma induced in the pulsed YAG laser welding of Al-Mg alloys in air and argon atmospheres. In the air environment, the identified spectra were atomic lines of Al, Mg, Cr, Mn, Cu, Fe and Zn, and singly ionized Mg line, as well as strong molecular spectrum of AlO, MgO and AIH. It was confirmed that the resonant lines of Al and Mg were strongly self-absorbed, in particular in the vicinity of pool surface. The self-absorption of atomic Mg line was more eminent in alloys containing higher Mg. These facts showed that the laser-induced plasma was relatively a low temperature and high density metallic vapor. The intensities of molecular spectra of AlO and MgO were different each other depending on the power density of laser beam. Under the low power density irradiation condition, the MgO band spectra were predominant in intensity, while the AlO spectra became much stronger in higher power density. In argon atmosphere the band spectra of MgO and AlO completely vanished, but AlH molecular spectra was detected clearly. The hydrogen source was presumably the hydrogen solved in the base Metal, absorbed water on the surface oxide layer or H$_2$ and $H_2O$ in the shielding gas. The temporal change in spectral line intensities was quite similar to the fluctuation of keyhole. The time average plasma temperature at 1 mm high above the surface of A5083 alloy was determined by the Boltzmann plot method of atomic Cr lines of different excitation energy. The obtained electron temperature was 3, 280$\pm$150 K which was about 500 K higher than the boiling point of pure aluminum. The electron number density was determined by measuring the relative intensities of the spectra1lines of atomic and singly ionized Magnesium, and the obtained value was 1.85 x 1019 1/㎥.

• Journal of Animal Science and Technology
• /
• 제62권2호
• /
• pp.227-238
• /
• 2020

Use of raw feedstuffs for livestock is limited by low digestibility. Recently, fermentation of feedstuffs has been highlighted as a new way to improve nutrient absorption through the production of organic acids using inoculated microorganisms, which can also play a probiotic role. However, standard procedures for feedstuff fermentation have not been clearly defined because the process is influenced by climatic variation, and an analytical standard for fermented feedstuffs is lacking. This study aimed to evaluate the microbiological and biochemical changes of feedstuffs during fermentation at temperatures corresponding to different seasons (10℃, 20℃, 30℃, and 40℃). We also investigated the effects of yeast, lactic acid bacteria (LAB), and Bacillus spp. on fermentation and determined the results of their interactions during fermentation. The viable cells were observed within 8 days in single-strain fermentation. However, when feedstuffs were inoculated with a culture of mixed strains, LAB were predominant at low temperatures (10℃ and 20℃), while Bacillus spp. was predominant at high temperatures (30℃ and 40℃). A significant drop in pH from 6.5 to 4.3 was observed when LAB was the dominant strain in the culture, which correlated with the concentrations of lactic acid. Slight ethanol production was detected above 20℃ regardless of the incubation temperature, suggesting active metabolism of yeast, despite this organism making up a marginal portion of the microbes in the mixed culture. These results suggested that fermentation temperature significantly affects microbiological profiles and biochemical parameters, such as pH and the lactic acid concentration, of fermented feedstuffs. Our data provide valuable information for the determination of industrial standards for fermented feedstuffs.

• 생물환경조절학회지
• /
• 제6권4호
• /
• pp.292-298
• /
• 1997

본 연구에서는 반사필름 멀칭과 북측면의 반사판설치에 의한 보광이 토마토의 광이용에 미치는 영향을 밝히기 위해 토양 및 수경재배를 통해 토마토의 엽온변화, 기공특성, 증산.광합성속도 등의 변화들을 중심으로 검토하였다. 보광 처리에 의해 토마토엽의 기공밀도는 증가하였으나 기공의 크기와 면적은 차이가 얼었다. 근권부의 삼투포텐셜이 낮으면 광반사에 의한 기공저항이 컸고 증산속도는 낮았으며 엽온은 40.62$^{\circ}C$까지 상승했다. 또한 보광에 의해 광합성속도도 저하했으나 엽록소 함량에는 차이가 없었다. 반사필름 멀칭으로 온실가루이의 기피효과는 있었다 약광기 동절기에 반사필름 멀칭 등의 보광처리에 의한 증수나 품질향상은 엽의 기공밀도의 증가로 활발한 증산 .광합성작용으로 체내의 물질대사나 생장에 영향을 주고 그 결과 간접적으로 무기성분의 흡수나 분배에 영향을 주어 생육 및 수량 둥이 양호했다고 생각된다.

• 한국생활과학회지
• /
• 제19권4호
• /
• pp.699-707
• /
• 2010

Catechu is widely used as in natural dyeing as well as in various medicines and tannage. This study investigated the dyeing properties and functionality of Catechu through a series of dyeing experiments using cotton fabric. It was shown that the absorbance of Catechu solution has two peaks at 220nm and 280nm. Thus, it can be concluded that the color constituent of Catechu is a catechol tannin and color tone is YR. The dyeability of Catechu increases as the concentration of the dye is increased. Its variation was shown to be similar to the isothermal absorption curve of the Freundlich. As dyeing time was increases, the dyeability did not change significantly after the 30 minute mark was passed. At high temperatures the dyeability was shown to increase. As the dyeing temperature was increased the color of dyeing fabrics changes from Y and YR to R. Experiments with pre-mordanting method showed that various colors can be obtained using Catechu. Cotton is effective in using K, Cu, Fe mordants, and the dyeability was shown to be improved with low pH. Both washing fastness and light fastness were shown to be low. However, the fabric color gradually changed to red was due to mailard reaction of catechol tannin causing by repeated washing and sunlight. The ultraviolet-cut ability was improved for cotton fabric dyed with Catechu. Also, dyed fabric with Catechu showed very good antimicrobial abilities at 99.9%.