• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.111-114
• /
• 2011

Waterprooping Method with sheet need to study technology and multilateral verification considering the arctic conditions as low temperature and humidity, which is the result only considered of material aspects without environmental condition in construction But there are no measures up until now. To solve this problem by using high frequency induction heating method developed waterproof sheets, cold (5 ℃ or less) can be applied in a more stable environment, water-resistant materials and construction methods were studied for development. The results of the test showed that high frequency induction heating method is effective for usability in low temperature condition and securement of proper quality than existing Waterprooping Method with sheet need.

• Journal of information and communication convergence engineering
• /
• 제6권3호
• /
• pp.305-309
• /
• 2008

This paper presents an innovative prototype of a new conceptual electromagnetic induction eddy current based fluid heating appliance using voltage-fed quasi resonant zero voltage soft switching PWM high-frequency inverter using IGBTs, which can operate at a constant frequency variable power regulation scheme. The promising simple high efficient low noise inverter type electromagnetic induction eddy current based pipeline fluid heating appliance is proposed for saturated steam generator, superheated steam generator, hot water and hot air producer, metal catalyst heating for exhaust gas cleaning in engine. Under these technological backgrounds, a novel electromagnetic induction eddy current Dual Packs Heater(DPH) based pipeline fluid heating incorporates thin metal layer type package for continuous fluid heating appliances applying two types of voltage-fed quasi load resonant ZVS-PWM high frequency inverter. The unique features of a novel electromagnetic induction eddy current DPH based continuous pipeline fluid heating appliance is illustrated on the basis of simulation and discussed for the steady state operating characteristics and experimental results.

• 비파괴검사학회지
• /
• 제27권3호
• /
• pp.268-279
• /
• 2007

The reliability of cold-bonding repair technique of carbon-fiber reinforced plastics (CFRP) laminates, often used as a temporary repair for the airplane maintenance, has been evaluated during cyclic loading and localized heating by nondestructive methods. Major concern was given to the evolution of damage after repair in the form of delaminations due to localized heating and cyclic loading combined. An area of interest both on the specimen repaired by cold-bonding and the specimen without repair where delaminations were induced by localized heating and cyclic loading was monitored by acoustic emission (AE) testing and further examined by pitch-catch low-frequency bond testing, and pulse-echo high-frequency ultrasonic testing. The results showed that the reliability of cold-bonding repair would be significantly reduced by the localized heating and cyclic loading combined rather than by the cyclic loading only. AE monitoring appeared to be an effective and reliable tool to monitor the integrity of temporarily repaired CFRP laminates in terms of the structural health monitoring (SHM) philosophy.

• 융합신호처리학회논문지
• /
• 제19권2호
• /
• pp.61-67
• /
• 2018

용접예열은 본 용접 전에 금속이 융착되는 모재면을 일정한 온도로 가열하는 것을 의미한다. 냉각속도 조절에 따른 재료 경화 정도 감소, 불순물 편석억제, 열적 변형방지, 그리고 수분제거 등 인접 영향부의 균열을 방지할 수 있다. 이러한 이유에서 고품질의 용접을 위하여 반드시 필요한 작업이다. 유도가열은 전자기유도 현상을 응용하여 전기에너지를 열에너지로 변환시키는 효율적인 가열방식이다. 기체 및 액체를 이용한 연소발열과 비교하여 신속한 가열뿐만 아니라 청결하고, 안정적이며, 경제적이다. 단순한 구조로 주파수와 코일의 형태를 변형하여 가열체의 형상, 깊이, 재질에 관계없이 가열할 수 있다. 본 논문에서는 유도가열 기법을 이용하여 저주파 용접예열 시스템을 구현하였으며, 3종의 자동차 변속기 부품을 대상으로 권선코일 내에서 각 변속기 높이에 따라 권선코일 저항, 인덕턴스 및 자동차 변속기 부품의 온도변화를 관찰한 결과 전류의 변화는 저주파 가열에 있어 매우 중요한 요인으로 작용함을 확인하였다.

• 대한기계학회논문집A
• /
• 제32권6호
• /
• pp.533-539
• /
• 2008

An high frequency induction hardening technology of vehicle body press-formed of thin sheet steel has been developed to increase the strength of vehicle body parts locally by high frequency induction heating, thereby eliminating the need for reinforcements. And this technique for increasing the tensile strength of sheet steel was practically applied to the front floor cross member and center pillar reinforcement of a passenger car. The side impact behavior has been investigated when induction hardening technology is applied to the conventional low-carbon steel and weight reduction of an automotive body is expected. In this paper, basic experiments were performed for the hat-shaped specimen under high frequency induction heating process. Martensitic transformation was found in the heating zone through microscopic observation which showed higher hardness. In addition, the hardness and strength of the center-pillar specimen made of boron steel increased remarkably by high frequency induction heating.

• 한국산업융합학회 논문집
• /
• 제22권5호
• /
• pp.491-497
• /
• 2019

Dissimilar friction welding were produced using 15 mm diameter solid bar in superalloy(Alloy718) to chrome molybdenum steel(SCM440) to investigate their mechanical properties. Consequently, optimal welding conditions were n=2000 rpm, HP=60 MPa, UP=120 MPa, HT=10 sec and UT=10 sec when the metal loss(Mo) is 3.5 mm. Acoustic Emission(AE) technique was applied to analyze the dissimilar friction welding of Alloy718 and SCM440. The relationship between the AE parameters and dissimilar friction welding of both material was discussed. In the case of heating time of 6 sec, 10 sec, 14 sec and 20 sec, 5 AE events per 0.5 seconds and energy about $2.7{\times}10^{10}$ were exhibited in heating time. In upsetting time, resulting in various numbers of events per second and very low energy. The frequency range of the signal generated during the heating time was about 200 kHz. However, the upsetting time resulted in a wide range of signals from very low frequency to high frequency of 500 kHz due to rapid plasticity of the material.

• 전기학회논문지
• /
• 제66권1호
• /
• pp.61-65
• /
• 2017

In this paper a prototype of high frequency heating power supply system based on the high frequency heating principle is designed to take the place of acupuncture, moxibustion, warm dressing treatment and some other traditional physical therapy methods. Which possess the advantages of low cost, convenient, easy operation and good effect. The high frequency heating power supply can generate a pulse voltage of more than 1KV with 300KHz switching frequency to heat the patient's skin. The skin temperature can reach to $41{\sim}42^{\circ}C$. The peak current control method is used to maintain the skin temperature in the designed range. The design of the main circuit is based on the flyback converter topology. An easier and practical design method is proposed in this paper. The power supply system prototype is verified to be stable and reliable by both the simulation and experimental results.

• 항공우주시스템공학회지
• /
• 제15권5호
• /
• pp.1-7
• /
• 2021

Ti-6Al-4V 티타늄 합금은 무게 대비 우수한 강도와 고온 강도 특성 때문에 수요가 증가하고 있지만 상온에서 낮은 성형성 때문에 고온으로 성형을 해야 한다. 현재 진행된 고온 성형 연구는 하부 금형을 가열하여 시편을 가열하는 방식이기 때문에 제약이 많다. 기존 고온 성형 방식과 다르게 제품을 국부적으로 가열할 수 있는 고주파 유도가열을 적용한다면 가공의 효율성을 높일 수 있을 것으로 예상된다. 또한 공정 기술 개발 시 신뢰도 높은 해석 기법으로 미리 공정을 시뮬레이션한다면 시간과 비용을 절약할 수 있다. 본 논문에서는 고주파 유도가열을 이용하여 Ti-6Al-4V 합금을 가열하였고 실험 결과와 전자기-열전달 연동 해석 결과를 비교하여 해석의 신뢰도를 판단하였다.

• Journal of Power Electronics
• /
• 제13권2호
• /
• pp.322-328
• /
• 2013

This paper presents a modified Current Source Parallel Resonant Push-pull Inverter (CSPRPI) for single phase induction heating applications. One of the most important problems associated with current source parallel resonant inverters is achieving ZVS in transient intervals. This paper shows that a CSPRPI with the integral cycle control method has dynamic ZVS. According to this method, it is the Phase Locked Loop (PLL) circuit that tracks the switching frequency. The advantages of this technique are a higher efficiency, a smaller package size and a low EMI in comparison with similar topologies. Additionally, the proposed modification results in a low THD of the ac-line current. It has been measured as less than %2. To show the validity of the proposed method, a laboratory prototype is implemented with an operating frequency of 80 kHz and an output power of 400 W. The experimental results confirm the validity of the proposed single phase induction heating system.

• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.407-411
• /
• 2011

The technology of line heating has evolved in various methods. Among them, fossil fuels like ethylene gas and LPG(Liquid Petroleum Gas) are widely used due to their simple utility. In the meantime, the technology implementing high frequency for line heating has also been developed continually, but its manufacturing technology or application includes lots of problems by now. One of the main characteristics of line heating using conventional technolob'Y is the quenching effect followed by heating process. On the other hand, hydrox gas which is mixed by hydrogen and oxygen is a prominent candidate for an application without above shortcomings. Especially, it is found that line heating using hydrox gas is tremendously effective taking low cost as well as low noise. In this paper, a small cell with high efficiency which can minimize installing space is developed to deal with the problem installing in narrow place. Experiments to prove the validation, efficiency and effectiveness is carried out by characterizing in the line heating of steel. It is found that the energy saving of using hydrox gas for line heating is significant and that the deviation performance is reduced by 78~89%. Furthermore, the noise is also reduced as amount of 18.3% though the heating time is not too different.