• Journal of the Korean Institute of Navigation
• /
• v.25 no.1
• /
• pp.53-60
• /
• 2001

This paper presents the fabrication of the LNA which is operating at 2.13 ~ 2.16 GHz for IMT-2000 front-end receiver using series feedback and resistive decoupling circuit. Series feedback added to the source lead of a GaAs FET keeps the low noise characteristics and drops the input reflection coefficient of a low noise amplifier simultaneously. Also, it increases the stability of the LNA. Resistive decoupling circuit is suitable for input stage matching because a signal at low frequency is dissipated by a resistor in the matching network. The amplifier consists of GaAs FET ATF-10136 for low noise stage and VNA-25 which is internally matched MMIC for high gain stage. The amplifier is fabricated with both the RF circuits and self bias circuit on the Teflon substrate with 3.5 permittivity. The measured results of the LNA which is fabricated using the above design technique are presented more than 30 dB in gain, PldB 17 dB and less than 0.7 dB in noise figure, 1.5 in inputㆍoutput SWR(Standing Wave Ratio).

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.4
• /
• pp.21-25
• /
• 2014

The silicon nitride ($SiN_x$) film for surface passivation and anti-reflection coating of crystalline silicon solar cell is very important and it is generally deposited by plasma enhanced chemical vapor deposition (PECVD). PECVD can be divided into low and high frequency method. In this paper, the $SiN_x$ film deposited by low and high frequency PECVD method was studied. First, to optimize the $SiN_x$ film deposited by low frequency PECVD method, the refractive index was measured by varying the process conditions like $SiH_4$, $NH_3$, $N_2$ gas rate, and RF power. When $SiH_4$ gas rate was increased and $NH_3$ gas rate was decreased, the refractive index was increased. The refractive index was also increased with RF power decline. Second, to compare the characteristics of the low and high frequency PECVD $SiN_x$ film, the refractive index was measured by varying $NH_3/SiH_4$ gas ratio and RF power and the minority carrier lifetime of before and after high temperature treatment process was also measured. The refractive index of both low and high frequency PECVD $SiN_x$ film was decreased with increase in $NH_3/SiH_4$ gas ratio and RF power. After high temperature treatment process, the minority carrier lifetime of both low and high frequency PECVD $SiN_x$ film was increased and increased degree was similar. The minority carrier lifetime of low frequency PECVD $SiN_x$ was increased from $11.03{\mu}m$ to $28.24{\mu}m$ and that of high frequency PECVD $SiN_x$ was increased from $11.60{\mu}m$ to $27.10{\mu}m$.

• 한국해양학회지
• /
• v.20 no.3
• /
• pp.37-54
• /
• 1985

A description of the "phytohydrography" in the southwestern waters of the East Sea is given from concurrent measurement of temperature, chlorophyll-a, nutrients, and phytoplankton and also from the calculated primary production during the two cruises in May and October, 1984. Past history of water mass is relatively well reflected in the distribution of phytoplankton species, but such a reflection is rarely shown in the distribution of physical and chemical parameters in general. Upper layer of the waters around Ul-gi and Gampo is typically characterized by the high chlorophyll-a, high primary production, and low nanofraction ratio due to the continuing supply of nutrients from the nutrient-rich cold water underneath. Water of Tsushima current shows poor standing crop in terms of cell numbers and chlorophyll-a concentrations, extremely high nanofraction ratio, and very low primary production. The overwhelming importance of the nanofraction is confirmed in phytoplankton cell numbers, chlorophyll-a concentration, and possibly enough in primary production. This emphasizes the exceptionally strong inflow of warm water into the study area from south among all the waters around the whole Korean peninsula.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.14 no.1
• /
• pp.31-38
• /
• 2008

Nursing Homes are different from other medical facilities, because they have a living space. And most of residents in a nursing home have dementia, therefore nursing homes are in control of outdoor activities for resident's safety and most of residents live in the living room at the daytime. The purpose of this study is analysis of spacial behaviors of residents in the living room, and reflection of the analysis into the architectural plan of nursing homes.There are two activities, individual activity and social interchange activity, in a living room and the role of a living room is semi-private space that includes both of them. Most numerous activities are watching TV and take a eat. Activities are different in accordance with the position at the living room. Individual activity and social interchange activity is same ratio in the middle and the ratio of social interchange activities are more than individuals in outside of living room. but alcove use of private.The types of living rooms are distinguished by combination of functions of livingroom, activity-room, and diningroom. The activity of use of residents have been shown different phases following the types of livingroom. The type of combination has been seen high rate of use and private activities and social communications are expressed evenly. The type of mixing has been seen low rae of use, but two activities, the above, are equal. The type of separation has been seen not only low rate of use, but also there has been only private activities.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.347.1-347.1
• /
• 2016

Screen printing is commonly used to form the electrode for crystalline silicon solar cells. However, it has caused high resistance and low aspect ratio, resulting in decrease of conversion efficiency. Accordingly, Ni/Cu/Ag plating method could be applied for crystalline silicon solar cells to reduce contact resistance. For Ni/Cu/Ag plating, laser ablation process is required to remove anti-reflection layers prior to the plating process, but laser ablation results in surface damage and then decrease of open-circuit voltage and cell efficiency. Another issue with plating process is ghost plating. Ghost plating occurred in the non-metallized region, resulting from pin-hole in anti-reflection layer. In this paper, we investigated the effect of Ni/Cu/Ag plating on the electrical properties, compared to screen printing method. In addition, phosphoric acid layer was spin-coated prior to laser ablation to minimize emitter damage by the laser. Phosphorous elements in phosphoric acid generated selective emitter throughout emitter layer during laser process. Then, KOH treatment was applied to remove surface damage by laser. At this step, amorphous silicon formed by laser ablation was recrystallized during firing process and remaining of amorphous silicon was removed by KOH treatment. As a result, electrical properties as Jsc, FF and efficiency were improved, but Voc was lower than screen printed solar cells because Voc was decreased due to surface damage by laser process. Accordingly, we expect that efficiency of solar cells could be improved by optimization of the process to remove surface damage.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.202-207
• /
• 2016

An auxiliary real-time train communications system among drivers, train-traffic controllers and field workers is necessary to share hazard information (i.e. rockfall detection, track maintenance) in low visibility zones (long tunnels and steep curved track). To develop the appropriate communication system, this paper proposes a new way of power line communication using the rail track (Rail - PLC), which has little noise and distortion of attenuation. Therefore, it is important to measure the impedance of the rail and to apply an impedance matching technique to increase the transmission characteristic of the Rail - PLC. This study would evaluate the reflection and the transmission characteristics of the rail using a network analyzer and an impedance matching transformer. The suitable impedance matching ratio was 1:3.28 from the result of back-to-back testing. The results confirmed that the transformer can improve the performance of the transmission signal in Rail - PLC using an impedance matching technique.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1383-1389
• /
• 2011

The current study focuses on the consistent analysis of heat transfer in multichannel volumetric solar receivers used for concentrating solar power. Changes in the properties of the absorbing material and channel dimensions are considered in an optical model based on the Monte Carlo ray-tracing method and in a one-dimensional heat transfer model that includes conduction, convection, and radiation. The optical model results show that most of the solar radiation energy is absorbed within a very small channel length of around 15 mm because of the large length-to-radius ratio. Classification of radiation losses reveals that at low absorptivity, increased reflection losses cause reduction of the receiver efficiency, notwithstanding the decrease in the emission loss. As the average temperature increases because of the large channel radius or small mass flow rate, both emission and reflection losses increase but the effect of emission losses prevails.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.727-732
• /
• 2020

In this paper, when a refractive index grating and a gain grating were simultaneously present in a DFB laser having a wavelength of 1.55 ㎛, a dielectric film coating was applied so that reflection did not occur on the right mirror surface, so that 𝜌_r=0. In case of δL > 0, the threshold gain and the beam distribution in the longitudinal direction and the radiated power ratio P_l/P_r of the oscillation mode were compared for the cases of the phase of 𝜌_l=π and π/2. If the phase of 𝜌_l=π, in order to obtain a low threshold current and high frequency stability, κL should be greater than 8. In the case of the phase of 𝜌_l= π/2, when κL is larger than 4.0, the oscillation gain starts to be lower than when the phase of 𝜌_l=π. In order to lower the threshold current of a oscillation mode and enhance the frequency stability, κL should be greater than 8.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.643-646
• /
• 2005

The gas hydrate exploration using seismic reflection data, the detection of BSR(Bottom Simulating Reflector) on the seismic section is the most important work flow because the BSR have been interpreted as being formed at the base of a gas hydrate zone. Usually, BSR has some dominant qualitative characteristics on seismic section i.e. Wavelet phase reversal compare to sea bottom signal, Parallel layer with sea bottom, Strong amplitude, Masking phenomenon above the BSR, Cross bedding with other geological layer. Even though a BSR can be selected on seismic section with these guidance, it is not enough to conform as being true BSR. Some other available methods for verifying the BSR with reliable analysis quantitatively i.e. Interval velocity analysis, AVO(Amplitude Variation with Offset)analysis etc. Usually, AVO analysis can be divided by three main parts. The first part is AVO analysis, the second is AVO modeling and the last is AVO inversion. AVO analysis is unique method for detecting the free gas zone on seismic section directly. Therefore it can be a kind of useful analysis method for discriminating true BSR, which might arise from an Possion ratio contrast between high velocity layer, partially hydrated sediment and low velocity layer, water saturated gas sediment. During the AVO interpretation, as the AVO response can be changed depend upon the water saturation ratio, it is confused to discriminate the AVO response of gas layer from dry layer. In that case, the AVO modeling is necessary to generate synthetic seismogram comparing with real data. It can be available to make conclusions from correspondence or lack of correspondence between the two seismograms. AVO inversion process is the method for driving a geological model by iterative operation that the result ing synthetic seismogram matches to real data seismogram wi thin some tolerance level. AVO inversion is a topic of current research and for now there is no general consensus on how the process should be done or even whether is valid for standard seismic data. Unfortunately, there are no well log data acquired from gas hydrate exploration area in Korea. Instead of that data, well log data and seismic data acquired from gas sand area located nearby the gas hydrate exploration area is used to AVO analysis, As the results of AVO modeling, type III AVO anomaly confirmed on the gas sand layer. The Castagna's equation constant value for estimating the S-wave velocity are evaluated as A=0.86190, B=-3845.14431 respectively and water saturation ratio is $50\%$. To calculate the reflection coefficient of synthetic seismogram, the Zoeppritz equation is used. For AVO inversion process, the dataset provided by Hampson-Rushell CO. is used.

• The Journal of Internal Korean Medicine
• /
• v.30 no.1
• /
• pp.173-180
• /
• 2009

Objectives : The aim of this study was to investigate the evaluation of gastrointestinal parasympathetic nerve activity by comparing between HRV and bowel sound parameters in patients with functional dyspepsia. Methods : 62 patients (male 22, female 40) were enrolled. HRV was measured in all patients. and TP (total power), LF (low frequency density: 0.04$\sim$0.15Hz), HF (high frequency density: 0.15$\sim$0.4Hz). and LF/HF ratio were analyzed. HF band is a reflection of parasympathetic activity. and the LF-to-HF ratio is considered a marker of sympathovagal balance. Bowel sounds were recorded at the day after, and postprandial %BS was used to indicate the gastric vagal activity after eating. HRV and bowel sound parameters were compared. and correlation between them was analyzed. Results : There was no difference in LF/HF ratio between patient group and healthy group of other report. According to values of %BS, each patient was classified into a normal (>6 %BS) or hypoactivity (<6 %BS) of gastric vagus nerve group. HF component of the hypoactivity group was not significantly higher than that of the normal group. There was no correlation between HRV and bowel sound parameters. Conclusions : Because no correlation was found between HRV and bowel sound parameters in patients with functional dyspepsia, we concluded that it is not proper to evaluate gastric vagus nerve activity by HRV measurement.