• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.2
• /
• pp.87-94
• /
• 2023

As the latest weapon systems and electronic equipments are increasingly demanding stealth technology to improve the survivability of allies, it is necessary to implement low-observability technology that reduces the radar cross section(RCS). In order to implement this stealth technology, a method for low RCS characteristics by applying a shape design or a electromagnetic wave absorber is widely used. However, active phased array antennas have structural limitations in shape design, also when a absorber is applied to it, the performance of the antenna is degraded. Therefore, in this paper, in order to realize the low RCS characteristics of the active phased array antenna operating in the X-band, individual radiating elements suitable for applying the radio wave absorber were selected, and a 13x13 array antenna was designed and manufactured. Next, by comparing the measured results of the relative RCS and electrical performance for the manufactured antenna according to the presence and type of the absorber, it is shown that the electrical performance is maintained at an equal or higher level while obtaining the low RCS characteristics. Thereby the method proposed in this paper for implementing the low RCS characteristics was validated. Finally, it was confirmed that when the wave absorber is applied to the array antenna, the limitation of its performance deterioration can be overcome.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.1
• /
• pp.59-65
• /
• 2020

Many technologies are being studied to reduce the RCS(Radar Cross Section) of stealth aircraft. Most RCS-reduction technlogies correspond to platforms. It is important to identify factors that RCS performance through simulation analysis of aircraft Mounted equipment. In particular, there are no studies of RCS performance in the radar frequency band when antenna transmit signals are applied. In this paper, the RCS performance variation on the transmit signal on/off of antennas mounted on a stealth aircraft was verified. Antennas were selected for each frequency band and simulated analysis to the RCS performance changes during antenna transmitting signal. Finally, to verify the characteristics of the change in RCS performance, RCS test measurements on the low-profile antenna transmit signal on/off were performed. In addintion, antenna RCS test measurement was performed according to the change of transmit signal power output. As a result, it was confirmed that there is no change in RCS performance when an antenna transmit signal is applied.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.194-196
• /
• 2022

When electromagnetic wave transmitted from the radar antenna hits the target, a specific type of electric field is formed according to the electrical characteristics and appearance of the target, which is called an RCS pattern. There are various commercial programs that calculate the RCS of the target and plot the RCS pattern. For the analysis of large targets such as warships or ships, a program with a high frequency analysis method, which has a faster calculation speed than the low frequency analysis method is suitable. XGTD, a high-frequency analysis program, can quickly plot a two-dimensional RCS pattern for 360 degrees of a target, but a three-dimensional RCS pattern cannot be obtained. In this paper, it is proposed that a method of plotting two-dimensional RCS patterns of a target from various angles using XGTD, generating a three-dimensional RCS pattern using this, and converting it into a three-dimensional antenna pattern file.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.843-850
• /
• 2012

To satisfy the operational requirements of surveillance radar and the operational concept of a ship combat system, an active-array-type antenna was designed using solid-state transmitters and receivers. The arrangement of the constituent electronic components of the antenna system, considerably large in size, and therefore, the antenna needs to be housed in a box. The rotational antenna system installed on a ship mast is installed in a sealed housing to protect the interior equipment from environmental conditions. The outer shape of the housing is that the antenna should be capable of rotating normally despite strong winds. Furthermore, in recent times, designs with low radar cross section (RCS) have attracted attention from the viewpoint of improving the stealth of the ship. In this light, four types of models are proposed for the outer shape design of the antenna system, and they are investigated from the viewpoint of low RCS design as well as wind load.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.10
• /
• pp.49-58
• /
• 2008

Characteristics of JEM(Jet Engine Modulation) are measured and principal meanings are grasped in this paper. This study's object is to measure RCS and JEM for actual aircraft, especially low speed craft. In experiment, various error are generated from unknown cause and for removal these, calibration technique known as IACT(Isolated Antenna Calibration Technique) is used. Experiment is executed at outdoor and target is T-103 which play in beginner course for ROKAF pilot. JEM spectrum of T-103 and frequency characteristics, doppler effects are extracted. X-band used in military aircraft for air-to-air fighting are selected. The data obtained through this study are analyzed to discriminate target especially low speed aircraft for current using radar(X-band)'s performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.8
• /
• pp.1110-1116
• /
• 2021

In this paper, we propose a conformal Ku-band data link antenna to ensure low RCS of stealth UAV. As a phased array antenna with electrical beam steering function, a transmitter and a receiver were designed and manufactured for FDD communication, respectively. Each antenna is designed as a 12*12 planar array antenna and has a function to form a uni-directional pattern and a bi-directional pattern through phase control of unit elements. The beam steering range is designed to be able to steer up to 60 degrees in theta direction and 360 degrees in the phi direction. As a result of manufacturing and measurement, the conformal type radome has low transmission loss and meets the required specifications including system performance. The feasibility of mounting the stealth UAV has been confirmed, and future research directions such as interworking of baseband devices and conversion to digital beam steering function are suggested.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.5
• /
• pp.1243-1248
• /
• 2014

In General, LPI radar's detection probability by ES equipments is lower than that of conventional pulsed radar because of very low transmitting power and high antenna gain etc. LPI radar is a kind of RF stealth technique such as RCS reduction design. Therefore the ultimate goal of LPI radar is detection probability reduction by opponent. If one of the two, RCS value or LPI radar performance is not sufficient, own platform will be found first by opponent. In this paper, some considerations are suggested for detection probability reduction.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.519-526
• /
• 2021

In this paper, an array antenna for LOS datalink for mounting UAV(Unmanned Aerial Vehicle) of low-probability of intercept is presented. For low RCS, radome was designed by conformal form, and other components were inserted into the UAV. The antenna of the transmitter and receiver are each composed of 12×12 array antennas, and include a beam steering function by controlling the phase of the unit element for the Uni-directional pattern and the Bi-directional pattern. As a result of the measurement of the manufactured antenna, it was confirmed that all the required specifications were met, and the installing possibility of the UAV platform on low-probability of intercept in the future was confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.937-950
• /
• 2015

Microstrip reflectarray is an antenna which controls its radiation pattern with a number of reflective elements. Conventionally, the reflectarray has been researched to replace curved reflector antennas. In this paper, design theories of reflectarray is briefly introduced, and research trends of high gain and broadband reflectarrays are reviewed. To improve the gain of the reflectarrays, it is required that the reflection phase errors on the reflectarray surface be minimized. For this purpose, sufficiently wide reflection phase range and low phase sensitivity should be realized with the designed element. For bandwidth improvement, the reflection phase of the element should be linear with the frequency variation. In this paper, various researches to improve the reflection phase characteristics of the element for high gain and broadband reflectarrays, such as multi-layer and single-layer multi-resonant structures, are reviewed. Also, dual-reflectarray configuration for compact antenna design is reviewed. Finally, various applications of reflectarrays such as contoured beam, near-field focusing, and RCS reduction are reviewed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.216-219
• /
• 2016

In this paper, the SIW(Substrate Integrated Waveguide)-based feeding antenna for the application of SDR(Software Defined Radar) is designed and manufactured. It is usually well-known that SIWs are easily integrated on PCB and have low transmission loss toward high powered input signal. Also, it is recommended that SIWs are strongly immunized to Electromagnetic Interferences(EMI). In particular, the manufactured antennas are loaded on the USRP(Universal Software Radio Peripheral) platform and employed to detect target RCS as an experiment in this paper. The operating frequency of the proposed antenna is in ISM(Industrial, Scientific and Medical) band(2.4~2.48 GHz) and the measured gain is over 8 dBi at 2.44 GHz.