• 대한전자공학회논문지SD
• /
• 제39권7호
• /
• pp.7-15
• /
• 2002

The digital DBS tuner is designed and implemented in a CMOS process using a direct-conversion architecture that offers a high degree of integration. To generate mathched LO I/Q quadrature signals covering the total input frequency range, a fully integrated ring oscillator is employed. And, to decrease a high level of phase noise of the ring oscillator, a frequency synthesizer is designed using a double loop strucure. This paper proposes and verifies a band selective loop for fast frequency switching time of the double loop frequency synthesizer. The down-conversion mixer with source follower input stages is used for low voltage operation. An experiment implementation of the frequency synthesizer and mixer with integrated a 0.25um CMOS process achieves a switching time of 600us when frequency changes from 950 to 2150MHz. And, the experiment results show a quadrature amplitude mismatch of max. 0.06dB and a quadrature phase mismathc of max. >$3.4^{\circ}$.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권3호
• /
• pp.404-416
• /
• 2015

Small-area, low-power coarse and fine frequency detectors (FDs) are proposed for an adaptive bandwidth referenceless CDR with a wide range of input data rate. The coarse FD implemented with two flip-flops eliminates harmonic locking as long as the initial frequency of the CDR is lower than the target frequency. The fine FD samples the incoming input data by using half-rate four phase clocks, while the conventional rotational FD samples the full-rate clock signal by the incoming input data. The fine FD uses only a half number of flip-flops compared to the rotational FD by sharing the sampling and retiming circuitry with PLL. The proposed CDR chip in a 65-nm CMOS process satisfies the jitter tolerance specifications of both USB 3.0 and USB 3.1. The proposed CDR works in the range of input data rate; 2 Gb/s ~ 8 Gb/s at 1.2 V, 4 Gb/s ~ 11 Gb/s at 1.5 V. It consumes 26 mW at 5 Gb/s and 1.2 V, and 41 mW at 10 Gb/s and 1.5 V. The measured phase noise was -97.76 dBc/Hz at the 1 MHz frequency offset from the center frequency of 2.5 GHz. The measured rms jitter was 5.0 ps at 5 Gb/s and 4.5 ps at 10 Gb/s.

• 한국군사과학기술학회지
• /
• 제14권1호
• /
• pp.1-8
• /
• 2011

In this paper, dual-feed circularly polarized microstrip patch antenna for GPS L1, GPS L2, GLONASS L1 signal was fabricated by using stacked patch. It was fed by dual coaxial probe on the patch at 50ohm impedance, and was simulated to resonate at GPS L1, GPS L2, GLONASS L1. To realize characteristics of right hand circular polarization using dual-feed stacked patch antenna and hybrid coupler for $90^{\circ}$ phase difference. Output of hybrid coupler was contacted input of Low Noise Amplifier(LNA). The LNA using dual band pass filter was designed and fabricated. The measured results of the implemented antenna is VSWR < 1.5 : 1 and the gain of 32dB(Zenith) over at GPS L1, L2, GLONASS L1.

• 한국해양공학회지
• /
• 제34권1호
• /
• pp.46-54
• /
• 2020

Oil spill accidents at sea result in a wide range of damages, including the destruction of ocean environments and ecosystems, as well as human illnesses by the generation of harmful gases caused by phase changes in crude oil. When an oil spill occurs, an immediate initial action should be performed to minimize the potential damage. Existing studies have attempted to identify crude oil spillage by calculating the crude oil spill range using synthetic aperture radar (SAR) satellite images. However, SAR cannot capture rapidly evolving events because of its low acquisition frequency. Herein, an algorithm for estimating an oil spill area from an image obtained using a digital camera is proposed. Noise that may occur in the image when it is captured is first eliminated by preprocessing, and then the image is analyzed. After analyzing the characteristics of the digital image, a strategy to binarize an image using the color, saturation, or lightness contained in it is adopted. It is found that the oil spill area can be readily estimated from a digital image, allowing for a faster analysis than any conventional method. The usefulness of the oil spill area measurement was confirmed by applying the developed algorithm to various oil spill images.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1873-1875
• /
• 1996

This paper deals with the lightning surge protective devices with combination of varistor and LC filter. UP to now, the varistor alone were used as overvoltage protection devices fer the AC power mains. In this work, in order to improve the cutoff performance of surge protective device, the hybrid circuit surge protective device for an AC single phase mains was designed and investigated. The first stage of hybrid circuit is to remove most of any large surge energy and protect the second stage components. The purpose of the second is to protect the load and increase the cutoff capacity of surge protective devices. Also LC filter attenuates the remnant that travels downstream from the first stage component and the high frequency noises. As a consequence, it was found that the proposed hybrid surge protective device for AC power mains has a variety of advantages such as low and tight clamping voltage, high frequency noise reduction and large cutoff capacity.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권3호
• /
• pp.125-132
• /
• 2002

PMSMS (permanent magnet synchronous motors) are widely used in industrial applications and home appliances because of their high torque to inertia ratio, superior power density, and high efficiency. For high performance control, accurate informations about the rotor position is essential. Sensorless algorithms have lately been studied extensively due to the high cost of position sensors and their low reliability in harsh environments. A novel position sensorless speed control for PMSMs uses indirect flux estimation and is presented in this paper. Rotor position and angular velocity are estimated by the proposed indirect flux estimation. Linkage flux and magnetic field flux are calculated by the voltage equations and the measured phase current without any integration. Instead of linkage flux calculation with integral operation, indirect flux and differential magnetic field are used for the estimation of rotor position. A proper rejection technique fur current noise effect in the calculation of differential linkage flux is introduced. The proposed indirect flux detecting method is free from the integral rounding error and linkage flux drift problem, because differential linkage flux can be calculated without any integral operation. Furthermore, electrical parameters of the PMSM can be measured by the proposed TCM (time compression method) for soft starting and precise estimation of rotor position. The position estimator uses accurate electrical parameters that are obtained from the proposed TCM at starting strategy. In the operating region, a proper compensation method fur temperature effect can compensate fir the estimation error from the variation of electrical parameters. The proposed novel position sensorless speed control scheme is verified by the experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.204-206
• /
• 2002

For small capacity rectifier circuits such as these for consumer electronics and appliances. capacitor input type rectifier circuits are generally used Consequently. various harmonics generated within the power system become a serious Problem. Various studies of this effect have been presented previously. However. most of these employ switching devices, such as FETs and the like. The absence of switching devices makes systems more tolerant to over -load, and brings low radio noise benefits. We propose a power factor correction scheme using a LC resonant in commercial frequency without switching devices. In this method. It makes a sinusoidal wave by widening conduction period using the current resonance in commercial frequency. Hence, the harmonic characteristics can be significantly improved. where the lower order harmonics. such as the fifth and seventh orders are much reduced. The result are confirmed by the theoretical and expermental implementations.

• 센서학회지
• /
• 제12권4호
• /
• pp.185-190
• /
• 2003

최근 적외선이나 초음파, 전자기파 등을 이용해 자연의 신호를 검출해 내는 센서들이 여러 가지 응용분야에서 널리 사용되고 있다. 더욱이 어떤 대상물이 가지고 있는 정보를 감지하는 고성능의 단일센서뿐만 아니라 이를 시스템적으로 개발하고 응용하는 것의 필요성도 높아져 왔다. 본 논문에서는 마이크로파를 이용한 레이더 센서 시스템을 설명하였고, 그 중 CW (Continuous Wave) 도플러 레이더를 이용한 마이크로파 센서 시스템의 동작 및 응용을 살펴보았다. 또한 이러한 시스템에 사용될 수 있는 고안정 주파수원으로 유전체 공진 발진기를 설계 제작하여 상용 시스템으로의 적용 가능성을 보였다. 제작된 유전체 공진 발진기는 12.67 GHz에서 동작하고, 출력전력이 +5.33 dBm 위상잡음은 100 kHz 옵셋주파수에서 -108.5 dBc/Hz를 얻었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1840-1842
• /
• 1998

Gyroscope is a very important core sensor, as a rotation sensor in inertial space, in inertial guidance and navigation system on aeronautics, plane, vessel and so on for civilian and millitary applications. Mechnical gyroscopes, adopting a principle of spinning a top, have been used in many application system. These mechnical gyroscopes need high power consumption, long warming time and complicated peripheral devices. But fiber-optic gyroscopes, based on the Sagnac effect, have novel advantages as small volume. simple scheme, low power consumption and high reliability. So we have developed a Intermediate grade All-fiber Optic Gyroscope, which has open-loop and minimum reciprocal configuration scheme. We have designed feedback circuits for stability of amplitude and phase using four lock-in amplifier(LIA) circuits and also used for noise limitation. This paper describes the scheme of optical part and electronic part and also test results of this all-fiber optic gyroscope. The performance have been achieved as long-term bias drift of $9.54^{\circ}/h$, random walk of $0.0317^{\circ}/\sqrt{h}$ and dynamic range of ${\pm}150\;deg/s$.

• 한국전기전자재료학회논문지
• /
• 제25권3호
• /
• pp.229-235
• /
• 2012

This paper dealt with the fabrication of a partial discharge (PD) analyzer for insulation diagnosis of power facilities like transformers, cables and gas-insulated switchgears. An analytic algorithm for the phase (${\phi}$), the magnitude (q), and the pulse count (n) of PD pulse was designed and a time-frequency (TF) map algorithm was applied in the system to eliminate noises by analyzing the time and the frequency component of signals. All the algorithms were operated by a LabView graphical program. The detection circuit consists of a coupling capacitor, a detection impedance, and a low noise amplifier. A plane-plane and a point-plane electrode system were fabricated to simulate different types of insulation defects. In the experiment, we could easily understand the characteristics of PD pulses using the prototype PD analyzer.