• 한국소음진동공학회논문집
• /
• 제21권10호
• /
• pp.890-896
• /
• 2011

For developing acoustic window, transmission loss in accordance with incident angle was calculated and compared with measurement results. In design stage, the material choice of acoustic window is very important because the material is one of main parameters of transmission loss and structural strength. In order to analyze the effect of material properties on transmission loss, the parametric studies were carried out and the results were discussed in this paper. And, to verify the design specification of acoustic window, measurement was carried out and the results were compared and analyzed.

• 한국전자파학회논문지
• /
• 제29권6호
• /
• pp.441-448
• /
• 2018

최근 국립전파연구원에서는 5G 이동통신 도심/부도심 지역에서 빌딩에 의한 클러터 손실을 예측하기 위해 3, 6, 10, 18, 24 GHz 대역에서 전파측정을 수행하였다. 본 연구에서는 송신안테나 높이가 85 m일 때, 도심과 부도심환경에서 주파수에 따라 측정된 클러터 손실을 비교하며, ITU-R P.2108 예측모델과의 오차를 평가하였다. 도심이나 부도심 지역에서 주파수가 높을수록 클러터 손실이 크게 나타나며, 도심 지역에서의 클러터 손실은 부도심 지역보다 더욱 강한 클러터 손실을 보이지만, ITU-R P.2108 예측 모델보다 낮은 클러터 손실을 얻어졌다. 결론적으로 측정된 데이터로부터 송신 안테나가 85 m로 높은 경우 도심/부도심 지역에서 클러터 손실에 대한 데이터를 예측모델에 반영하여 클러터 손실 예측모델을 좀 더 개선시켜 나갈 필요가 있다.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.395-398
• /
• 1995

For the core loss measurement under arbitrary waveform of magnetic induction, we have constructed a single sheet core loss measuring system which consists of yoke apparatus for single sheet of $10\;cm{\times}10\;cm$, arvitrary waveform synthesizer, B-feedback system, and two channel transient recorder. Using the constructed measuring system, we can measure core loss including higher harmonics up to 2 kHz. Core loss of non-oreinted electrical steel was increased exponentially when higher harmonic frequency was increased or amplitude of harmonic induction was increased.

• 대한기계학회논문집B
• /
• 제20권4호
• /
• pp.1501-1509
• /
• 1996

Differential pressure devices such as an orifice and Venturi are widely used in the measurement of flow rate of fluid mainly due to cost effectiveness and easy installation. In the current study, the viscoelastic effect on discharge and loss coefficients of those flow meters were investigated experimentally. Aqueous solutions of Polyacrylamide (200, 500, and 800 ppm) as viscoelastic fluids were used. Discharge coefficient of an orifice for viscoelastic fluids increased significantly up to approximately 15-20% when compared with that for water, while loss coefficient decreased up to 10-25% depending on the diameter ratio, .betha.. Also, pressure recovery for viscoelastic fluids was extended much longer than that for water. On the other hand, discharge and loss coefficients of Venturi for viscoelastic fluids were found to be strongly dependent on the Reynolds number. In both flow meters, the concentration effect for discharge and loss coefficients was not observed at more over than 200 ppm of aqueous solution. Conclusively, orifice and Venturi flow meters should be calibrated very carefully in the flow rate measurement for viscoelastic fluids.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권2호
• /
• pp.83-88
• /
• 2006

AC loss is one of the main research area in AC power application using high temperature superconductor(HTS), such as HTS transformer, HTS current limiter and HTS cable, because it is closely related to efficiency, economic estimation and design of power device. A lot of research for various arrangements of HTS tapes have been performed to increase a capacity of transport current because single HTS tape can not satisfy the demanded current capacity in HTS power application. In this paper, we studied magnetization loss by different several arrangements of BSCCO tapes such as Edge-to-Edge type, Face-to-Face type and Matrix type through numerical analysis by 2D-FEM and measurement. As a result, we got the result that the magnetization loss of Face-to-Face type arrangements was lower than those of other arrangement types under the conditions of the same stacking number. We think that the result was due to shield effect by demagnetization of adjacent HTS tapes which are located face to face.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.883-888
• /
• 2002

This study describes the limit and application of the two-microphone impedance tube method to the sound transmission loss measurement of several sound isolation materials with different physical properties. For the sound isolation materials having small flexural rigidity, it is shown that the two-microphone impedance tube method is validated to practically measure the sound transmission loss. For the sound isolation materials having large flexural rigidity, on the other hand, it is found that the two-microphone impedance tube method is no longer valid to measure the sound transmission loss because the regions of resonance and mass law are moved into the higher frequencies. In addition, in order to accurately measure the sound transmission loss of sound isolation materials, their size should be decided based on the consideration of the effect of acoustic excitation on their vibration response.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 I
• /
• pp.314-317
• /
• 2003

In this paper, a measurement and analysis program is developed, that can be utilized to measure and analyze radio propagation characteristics. This program is able to control the measurement instruments including spectrum analyzer through a GPIB interface, and analyze the measured data to yield mean excess delay and RMS delay spread. The measured path loss can be compared with theoretical path loss in free space or inside tunnels. The measured and analyzed results can also be presented in the forms of graphs. As those tasks can be conducted on the measurement spot, this program is very helpful for performing and verifying measurements.

• 전기학회논문지
• /
• 제61권8호
• /
• pp.1216-1220
• /
• 2012

The current collection between pantograph and contact wire is a more critical component for need to train speed up in electric railway. The basic purpose of this paper is to establish a measure of determining arc by developing an arc detector assessment system. The system was designed under conditions of EN 50317 and simulations were conducted using the developed device. According to the results, it was possible to conduct certification tests following regulations of international standards. To check the validity of our approach for the intended application, we analysis contact loss of catenary system using developed arcing measurement system in Korea. The proposed arcing measurement system is expected to enhance precision of current collection quality performance assessment methods at high-speed lines and conventional lines.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권9호
• /
• pp.960-967
• /
• 1997