• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.913-922
• /
• 2009

Fourteen model pile load tests using a calibration chamber and instrumented model pile were preformed to investigate the variation of the behaviors of driven piles in sands with soil and lateral cyclic loading conditions. Results of the model tests showed that the first loading cycle generated more than 70% of the pile head rotation developed for 50 lateral loading cycles. Lateral cyclic loading also made an increase of the ultimate lateral load capacity of piles for $K_0$=0.4 and an decrease for $K_0$ higher than 0.4. Higher portion of the increase or decrease in the ultimate lateral load capacity by lateral cyclic loading was generated for the first loading cycle due to densification of loosening of the soil around the pile by lateral cyclic loading. It was also observed that a two-way cyclic loading caused higher ultimate lateral load capacity of driven piles than a one-way cyclic loading. When the pile was in the ultimate state, the maximum bending moment developed in the pile increased with increasing $K_0$ value of soil and was insensitive to the magnitude and number of lateral cyclic loading.

• 대한치과보철학회지
• /
• 제55권3호
• /
• pp.251-257
• /
• 2017

목적:본 연구에서는 long internal connection 형태의 임플란트 지대주를 내부 연결 길이에 변화를 주어 임플란트-지대주 결합부의 안정성을 비교 평가해 보고자 하였다. 재료 및 방법: Long internal connection의 임플란트(Replus system, $4.7{\times}11.5mm$)를 각각 지대주의 길이에 따라 4개의 군(1, 2, 3, 4 mm 군)으로 나누었고 총 20개의 시편을 사용하였다. 시편을 레진에 매몰하여 고정시키고 100 N의 힘으로 임플란트 장축에 대해 30도의 각도에서 $1.0{\times}10^6$ 번의 반복하중을 가한 후 하중 전 후의 풀림회전력의 차이를 계산하여 95% 유의수준에서 Kruskal-Wallis 검정 방법을 통해 통계 분석하였다. 결과:지대주 내부 길이에 따른 풀림 회전력의 통계적 유의성은 나타나지 않았으며 (P > .05) 어떤 시편에서도 완전한 나사 풀림이나 나사 파절은 관찰되지 않았다. 결론: 내측 연결 임플란트에서 지대주 내부길이에 따른 나사 풀림의 정도는 차이가 나지 않았다.

• 한국표면공학회지
• /
• 제51권5호
• /
• pp.309-315
• /
• 2018

The purpose of this study is to assess the mechanical properties of the ceramic abutment with washer. In this study, ceramic abutment were used, tested with $30^{\circ}$ compression load, shear fatigue, adaptation accuracy test(rotation angle, contact interval), removal torque force test, torsional breaking force test. The $30^{\circ}$ compression load was 729 N, the shear fatigue load was 275 N, adaptation accuracy test of rotation angle was within $3^{\circ}$, contact interval within $10{\mu}m$, and removal torque force test value is $18.88N{\cdot}cm$, torsional breaking force test value is $35.52N{\cdot}cm$. Ceramic abutment with a washer fitted have sufficient mechanical strength and may be substituted for titanium abutment.

• 대한치과보철학회지
• /
• 제33권1호
• /
• pp.98-129
• /
• 1995

The purpose of this study was to evaluate how mandibular implant-supported fixed complete prosthesis, implant and mandible responded mechanically, according to curvature of arch, number and location of fixture, and amounts of load. The shape of mandibular arch was tapered or square form and, 4 or 6 fixtures were implanted in each arch model. A vertical load of 10kg was applied at the center of prosthesis and a vertical load of 20kg was applied at the location of the 10mm or 20mm cantilever posterior to the most distal implant. Three-dimensional finite element analysis was performed for stress distribution and deflection using commercial software(ABAQUS program) for Sun-SPARC Workstation. The results were as follows : 1. The case square arch form was more stable to compare with that of tapered arch form in respect of stress distribution and displacement under vertical load on the center of prosthesis. 2. 6-implants cases were more stable than 4-implants cases for decreasing bending torque under vertical load on the center of prosthesis. 3. Under vertical load on cantilever extension, the case of 10mm long cantilever was more stable than that of 20mm long cantilever in respect of stress distribution and displacement. 4. Under vertical load on cantilever extension, 6-implants cases had a tendency to reduce displacement and to increase the reaction force of supporting point due to increasing of the bending stiffness of the prosthesis than 4-implant case. 5. When the ends of 10mm or 20mm long cantilever were loaded, the most distal implant was under compressive stress but the second most distal implant was under the highest tensile stress and the remaining implants were under varying tensile stress. 6. Because 6-implants cases had smaller displacement than 4-implants cases, 6-implants cases were more favorable in respect of prevention of screw loosening under repeated loadings.

• 한국터널지하공간학회 논문집
• /
• 제13권3호
• /
• pp.215-231
• /
• 2011

본 논문에서는 연직 불연속면을 포함하는 지반에서 얕은 심도 2-arch 터널 굴착에 따른 거동특성을 실험적으로 연구하였으며, 2-arch 터널 굴착에 따른 필러부 하중전이 특성을 관찰하였다. 연직 불연속면의 위치를 변화시키고, 2-arch터널 시공단계별로 모형실험을 수행하였다. 실험결과, 2-arch 터널 굴착에 따른 이완하중이 불연속면이 위치한 곳에 집중되었고, 불연속면에 차단되어 불연속면을 넘어서까지 하중이 전이되지는 않았다. 또한 인접한 터널의 하반을 굴착할 때보다 상반을 굴착할 때에 필러부와 지반변형에 더 큰 영향을 미치는 것으로 나타났다.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1998년도 추계학술대회
• /
• pp.155-156
• /
• 1998

Screw loosening and subsequent pullout can be attributed to the reduction in bone mineral density in the vertebrae manifested by osteoporosis in which the decrease in fixation strength between the cancellous bone and screw threads are accelerated by repeated loads exerted by patients own weight and activities following the surgery. In this study, the change in pullout strength of the pedicle screws was investigated before and after repeated loads were imparted. For this purpose. Diapason pedicle screws $(6.7\times40mm)$ were inserted onto fresh porcine spine specimens (T1-L5) after bone mineral density was measured using a DEXA. With an MTS, an axial load was applied at a loading rate of 0.33mm/sec until failure to measure the maximum pullout strength. Flexion moment of 7.5N-m was then imparted at 0.5Hz for 2000 cycles. It was found that the maximum pullout strength was exponentially related to BMD regardless of load types ($107.71\;\times\;\exp^{(1.43{\times}BMD)}r^2=0.93$, P<0.0001 without repeated load; ($107.71\;\times\;\exp^{(2.19{\times}BMD)}r^2=0.78$, P<0.0001 with repeated load). The results suggest that the reduction in pullout strength for pedicle screws is far more prominent in osteoporotic spine than in normal spine especially as number of repeated load was increased. More importantly, it was demonstrated that the level of bone mineral density and the activity level of the patient should be evaluated in more detail for successful implementation of pedicle screw systems in spinal surgery.

• Structural Engineering and Mechanics
• /
• 제86권2호
• /
• pp.261-276
• /
• 2023

The use of the ordinary double nut (i.e., ODN) composed of a master nut (i.e., M-nut) and a slave nut (i.e., S-nut) is a highly efficient method to prevent bolts loosening. A novel double nut (i.e., FODN) composed of a master nut (i.e., M-nut) and flat slave nut (i.e., FS-nut) is proposed to save raw materials. The bolt fastening tests with single nut, ODN and FODN are performed to investigate the preload and counterbalance forces. Corresponding finite element analysis (FEA) models are established and validated by comparing the preload with the experimental results. The load-bearing capacity, the extrusion effect, and the contact stress of each engaged thread for ODN and FODN are observed by FEA. The experimental and simulated results revealed that the bolt fastening with double-nut has different load-transferring mechanisms from single-nut. Nevertheless, for double-nut/bolt assemblies, the FS-nut can provide load transfer that is like that of the S-nut, and the FODN is a reasonable and reliable fastening method. Furthermore, based on the theory of Yamamoto, a formula considering the extrusion effect is proposed to calculate the preload distribution of the double-nut, which is applicable to varying thicknesses of slave-nuts in double-nut/bolt assemblies.

• Smart Structures and Systems
• /
• 제11권4호
• /
• pp.349-364
• /
• 2013

Recently, researchers in the field of structural health monitoring (SHM) have been rigorously striving to replace the conventional NDE techniques with the smart material based SHM techniques, employing smart materials such as piezoelectric materials. For instance, the electromechanical impedance (EMI) technique employing piezo-impedance (lead zirconate titanate, PZT) transducer is known for its sensitivity in detecting local damage. For practical applications, various external factors such as fluctuations of temperature and loading, affecting the effectiveness of the EMI technique ought to be understood and compensated. This paper aims at investigating the damage monitoring capability of EMI technique in the presence of axial stress with fixed boundary condition. A compensation technique using effective frequency shift (EFS) by cross-correlation analysis was incorporated to compensate the effect of loading and boundary stiffening. Experimental tests were conducted by inducing damages on lab-sized aluminium beams in the presence of tensile and compressive forces. Two types of damages, crack propagation and bolts loosening were simulated. With EFS for compensation, both cross-correlation coefficient (CC) index and reduction in peak frequency were found to be efficient in characterizing damages in the presence of varying axial loading.

• 한국화재소방학회논문지
• /
• 제34권3호
• /
• pp.67-75
• /
• 2020

본 연구는 산업현장에서 사용되는 분전반 내 터미널 블록의 탄화 사고를 예방하기 위한 목적으로, 전선 접속부 볼트의 이상(Abnormal) 풀림 각도에 따라 변화하는 정상전류 및 과전류의 접속부 발열 위험성을 확인하고 열적 특성을 통해 위험성을 분석하였다. 이를 위하여 터미널 블록에 Resistance temperature detector (RTD) 센서 보드를 설치하여 실시간으로 터미널 블록의 발열 온도와 온도의 변화를 측정하는 새로운 기법을 적용하였다. 실험 결과 정격 전류가 작은 터미널 블록 모델의 발열 온도가 높게 나타남에 따라 부하전류에 따른 터미널 블록 용량 선정의 중요성을 확인하였다. 또한 정격전류가 높은 터미널 블록의 정격 전류가 높을수록, 이상 풀림 정도가 클수록 탄화점이 빨라짐을 확인하였다. 이러한 발열 온도 모니터링을 통해서 실시간 발열 온도를 측정할 수 있었고 열적 분석을 통해서 단계별 위험수위 설정이 가능함을 확인할 수 있었다. 본 연구의 탄화 위험성 측정 및 분석 결과는 탄화로 인한 화재 위험성에 대한 응용 연구의 이론적 기초를 제공할 수 있다. 또한 본 연구에서 새롭게 적용한 온도 센서 보드를 활용한 열화 측정 방법은 위험수준관리 및 전기적 접촉 불량으로 인한 화재 예방 활동에 광범위하게 적용 가능할 것으로 사료된다.

• 한국터널지하공간학회 논문집
• /
• 제8권4호
• /
• pp.365-375
• /
• 2006

일반적으로 터널2차라이닝의 구조해석에는 골조해석모델이 적용되고 있다. 본 모델은 경험적 방법에 의한 지반 이완하중을 고려하고 있으나 주관적이고 과대평가되는 경향이 있다. 2차라이닝에 작용하는 지반하중은 숏크리트 및 록볼트와 같은1차지보재의 지지력 상실에 기인한다. 그러므로 2차라이닝에 작용하는 지반하중 산정에는 1차지보재와 지반의 평형상태가 고려되어야 한다. 지반-라이닝 상호작용(Ground-Lining Interaction, GLI)모델은1차지보재의 지지력 상실에 의해 야기된 지반의 변형을2차라이닝이 지지하는 개념을 토대로 수립되었다. 따라서 GLI모델은 복잡한 지반조건과 1차 지보재의 설치조건을 합리적으로 반영한 지반하중을 고려할 수 있다. 2차라이닝에 작용하는 하중은 지반하중 외에 지하수압, 지진하중 등이 있다. 극한강도 설계법을 이용한 라이닝 구조보강을 위해서는 계수하중 및 다양한 하중조합이 고려되어야 한다. GLI모델은 계수하중을 고려하기 곤란하기 때문에 개별 하중에 대해 산정된2차라이닝 단면력에 하중계수를 곱하는 중첩의 원리를 적용하였다. 끝으로, 본 연구에서 제시된 GLI모델을 이용한 2차라이닝 설계방법을 저심도 지하철 터널에 적용하였다.