• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.36-45
• /
• 2010

In this paper, we propose a new design method to design a wireless power transfer system using loop antennas for consumer electronics. This method can simply design a wireless power transfer system only using measurements of coupling coefficients and simple equations of equivalent circuit model about loop antennas without complicated electromagnetic analysis. Using the proposed design method, a wireless power transfer system with a pair of loop antennas operating at the frequency of 13.56 MHz, which have a dimension of $50{\times}50\;cm^2$, is designed and implemented. The input return loss, coupling coefficient, efficiency, and input impedance variation with respect to a distance between loop antennas were measured. The proposed design method provides good agreements between measured and predicted results. Also, the wireless power transfer system with impedance matching circuits designed by the proposed design method shows two times higher efficiency characteristics than the case with the general $50\;{\Omega}$ impedance matching circuits. Therefore, we verified that our design method could be an effective tool to design a wireless power transfer system.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.152-155
• /
• 2011

This paper describes the role of mutual impedance and the transducer power gain which comes from key parameters to determine the amount of wireless power especially in a near-field environment. These two key parameters are applied to the two configurations; one is a dipole-dipole, and the other is a dipole-metal plate-loop configuration. Discussions are given on the achievable maximum power transfer between the sender and the receiver affected by the matching and the pass blockage.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1131-1139
• /
• 2004

A new impedance controller is proposed for bilateral teleoperation under a time delay. The proposed controller does not need to measure or estimate the time delay in the communication channel using the force loop-back. In designing a stable impedance controller, absolute stability is used as a stability analysis tool, which results in a less conservative controller than the passivity concept. Moreover, in order to remove the conservatism associated with the assumption of infinite port impedances, the boundaries of human and environment impedance are set to finite values. Based on this, this paper proposes a parameter design procedure for stable impedance controllers. The validity of the proposed control scheme is demonstrated by experiments with a 1-dof master/slave system.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.581-586
• /
• 2020

In this paper, the design process and method for a compact wideband loop antenna for terrestrial digital TV (DTV) and ultra high definition (UHD) TV applications was proposed. Horizontal slits were added on the two circular sectors of the proposed loop antenna in order to miniaturize the existing wideband loop antenna consisting of a square loop and two circular sectors. A CPW transmission line was inserted in the center of the lower circular sector as a feed line. The CPW feed line was designed using the 75 ohm port impedance for DTV and UHD TV applications, and a tapered center-signal line was designed to improve the impedance matching. The final designed antenna was fabricated on an FR4 substrate with a thickness of 0.8 mm. The experiment results show that the proposed compact loop antenna operates in the frequency band of 444.3-820.1 MHz for a VSWR < 2, which fully covers the DTV and UHD TV bands.

• Journal of information and communication convergence engineering
• /
• v.14 no.4
• /
• pp.222-226
• /
• 2016

A design method for a compact square loop antenna fed by a microstrip (MS) line for indoor digital television (DTV) applications is proposed. The proposed antenna consists of a square loop, circular sectors, and an MS line. The square loop combined with circular sectors is printed on one side of a substrate, and a $75-{\Omega}$ MS line is printed on the other side. The circular sectors are used as a wideband balun or transition to connect the MS line and the square loop. A prototype of the proposed square loop antenna operating in the DTV band (470-806 MHz) is designed and fabricated on an FR4 substrate. Experimental results show that the proposed antenna has the desired impedance characteristics in the frequency band of 464-1,220 MHz (89.8%) for a voltage standing wave ratio (VSWR) of <2 covering the DTV band, and a broadside gain of 0.8-3.3 dBi in the DTV band.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.9-15
• /
• 2006

This paper shows the impedance profile of PEEC(Partial Equivalent Electrical Circuit) PDN(Power Distribution Networks) including core and I/O circuit. Through the simulated results, we find that the core power noise having connection with I/O power is affected by I/O switching. Also, using designed $74{\times}5inch$ DLL(Delay Locked Loop) test board, we analyzed the effect of power noise on operation region of chip. Jitter of a DLL measure for frequency of $50{\sim}400MHz$ and compared with impedance obtained result of simulation. Jitter of a DLL are increased near about frequency of 100MHz. It is reason that the resonant peak of PDNs has an impedance of more the 1ohm on 100MHz. we present the impedance profile of a chip and board for the decoupling capacitor reduced the target impedance. Therefore, power supply network design should be considered not only decoupling capacitors but also core switching current and I/O switching current.

• Journal of Korean Society of Transportation
• /
• v.13 no.3
• /
• pp.67-86
• /
• 1995

It requires the detector system which can collect highly reliable traffic data in order to perform the real-time traffic signal control. This study is to decide the optimal shape of inductive loop for the real-time traffic signal control .This loop is located at the stopline in the signalized intersection for DS(Degree of Saturation) control. In order to find out the optimal shape of loop, 6types of experiments were performed . The results of the basic experiments of loops are as follows ; -the optimal number of turns for loop is 3 turns. -the impedance values of the loop detectors are similar to that of NEMA standards -the 1.8${\times}$4.5M loop is excellent for sensitivity in actual detection range of car length comparing to other shape of inductive loops. At the experimental of establishments of the optimal loop shape, it found that 1.8 4.5M loop has the highest values of $\DeltaL$ comparing to other types of loops, It means that the range of Lead-in cable length of this loop. And this loop is highly reliable in occpupancy time. Conclusivley, the 1.8${\times}$4.5M inductive loop is the optimal solution as a stop line loop detector for real -time traffic signal control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.1
• /
• pp.16-24
• /
• 2021

Solar array simulator (SAS) is essential equipment in testing and evaluating the power processing performance of a power conditioning system. However, the nonlinearity in the current(I)-voltage(V) characteristic makes the control loop design of SAS a challenging task. Conventionally, only the inner loop is usually considered in the control design approach. However, this study proves that the reference generation loop also interacts with the inner loop and plays a key role in the overall performance of the SAS. In this paper, the performance of voltage-mode control and impedance control, which are two of the most popular architectures for the SAS system, are reviewed and compared by multi-loop analysis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.8
• /
• pp.1492-1497
• /
• 2017

In this paper, a design method for a CPW-fed wideband loop antenna for indoor digital TV applications is studied. The proposed loop antenna consists of a square loop and two circular sectors which connect the loop with central feed points, and the CPW feed line is inserted in the lower circular sector. The CPW feed line is designed to match with the 75 ohm port impedance for DTV applications, and the ground slots are etched in order to improve the impedance matching in the middle frequency region. The effects of the gap between the circular sectors and the location and dimension of the ground slots on the input reflection coefficient and gain characteristics are examined to obtain the optimal design parameters. The optimized antenna is fabricated on FR4 substrate, and the experiment results show that it operates in the frequency band of 463-1,280 MHz for a VSWR < 2, which assures the operation in the DTV band.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.455-456
• /
• 2020

This paper proposes stability evaluation of DC/DC boost converters based on output impedance in harmonic transfer function matrix considering line impedance and cascaded voltage and current control loops. The harmonic state-space (HSS) model of converter and controller is developed to obtain the harmonic transfer function matrix of closed-loop output impedance. This work is useful for impedance-based stability analysis of converters connected to DC power systems.