• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.75-79
• /
• 2004

In this paper, a single plane wide band microstrip antenna for integrated circuit as MMIC and LTCC is designed and fabricated. A new configuration for a wide band microstrip antenna with omni-directional pattern is proposed. This antenna consists of two rectangular folded dipoles, which are fed by a coplanar waveguide(CPW). It was effected stabilization ground that a signal plane of CPW feed have been limited ground plane. Therefore, a ground plane of folded structure should be extended outside folded antenna in this research. The characteristics of the proposed antenna were analyzed by using an FDTD methods. The return loss and radiation patterns were simulated and measured. The proposed antenna is get 120MHz bandwidth of PCS band and 250MHz bandwidth of IMT2000 band, used ISM band.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.11
• /
• pp.664-670
• /
• 2004

This paper presents a new velocity estimation strategy of a non-salient permanent magnet synchronous motor (PMSM) drive without high frequency signal injection or special PWM pattern. This approach is based on the d-axis current regulator output voltage of the drive system that has the information of rotor position error. The rotor velocity can be estimated through a rotor position tracking PI controller that controls the position error to zero. For zero and low speed operation, PI controller gains of rotor position tracking controller have a variable structure according to the estimated rotor velocity. In order to boost the bandwidth of PI controller around zero speed, a loop recovery technique is applied to the control system. The proposed method only requires the flux linkage of permanent magnet and is insensitive to the parameter estimation error and variation. The designers can easily determine the possible operating range with a desired bandwidth and perform the vector control even at low speeds. The experimental results show the satisfactory operation of the proposed sensorless algorithm under rated load conditions.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.4
• /
• pp.49-56
• /
• 2002

In this paper, a new controller using non-linear compensator for position control is presented, which we can satisfy the given specifications more easily than the existing one. We suggest an improved PDFE(Integral with Proportional-Derivative-plus-Feedforward) controller by which both phase margin and bandwidth are controlled simultaneously in the controller design problem. Replacing the feed forward term in the PDFF system with a CDIDF(Complex Dual Input Describing Function), the desired phase margin is obtained without diminishing the bandwidth of the closed loop system. The effectiveness of the proposed controller is confirmed through simulations and experiments. As The results of these, we know that it is possible to adjust overall specifications by varying parameters in the improved PDFF system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.310-323
• /
• 2004

In this paper, we extend the multiple time scale control framework to window-based congestion control, in particular, TCP This is performed by interfacing TCP with a large tine scale control nodule which adjusts the aggressiveness of bandwidth consumption behavior exhibited by TCP as a function of "large time scale" network state. i.e., conformation that exceeds the horizon of the feedback loop as determined by RTT Our contribution is threefold. First, we define a modular extension of TCP-a function call with a simple interface-that applies to various flavors of TCP-e.g., Tahoe, Reno, Vegas and show that it significantly improves performance. Second, we show that multiple time scale TCP endows the underlying feedback control with preactivity by bridging the uncertainty gap associated with reactive controls which is exacerbated by the high delay-bandwidth product in broadband wide area networks. Third, we investigate the influence of three traffic control dimensions-tracking ability, connection duration, and fairness-on performance. Performance evaluation of multiple time scale TCP is facilitated by a simulation bench-mark environment which is based on physical modeling of self-similar traffic.

• Current Optics and Photonics
• /
• v.4 no.6
• /
• pp.472-476
• /
• 2020

We have investigated the impact of optical filter bandwidth on the performance of all-optical automatic gain-controlled (AGC) erbium-doped fiber amplifiers (EDFAs). In principle, an optical bandpass filter (OBPF) should be placed within the feedback gain-clamping loop to set the lasing wavelength as well as the passband of the feedback amplified spontaneous emission (ASE) in all-optical AGC EDFA. From our measurement results, we found that the power level of feedback ASE with 0.1 nm passband of the optical filter was smaller than the ones with >0.2 nm passband cases. Therefore, the peak-to-peak power variation of the surviving channel with 0.1 nm passband was much larger than the ones with >0.2 nm passband. In addition, no significant difference in the power level of the feedback ASE was observed when the passband of the optical filter was ranging from 0.2 nm to 4.5 nm in our measurements. From these results, we have concluded that the passband of the optical filter should be slightly larger than 0.2 nm by taking into account the effect of feedback ASE power and the efficient use of the EDFA gain spectrum for the lasing ASE peak.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.6
• /
• pp.71-76
• /
• 2010

In this paper, a 120 GHz local oscillator(LO) for the sub-harmonic mixer in the THz transceiver with a carrier frequency of 240 GHz was designed and fabricated. A 120 GHz local oscillator was composed of 40 GHz PLL(Phase Locked Loop), 40 GHz BPF(Band Pass Filter), frequency tripler and 120 GHz BPF. The commercial model of the frequency tripler was used. The measured result of the 40 GHz PLL showed the phase noise of -105 dBc/Hz at the 100 kHz offset frequency. The measured result of 120 GHz BPF showed the insertion loss of 1.3 dB at center frequency of 119 GHz with bandwidth of 5 GHz. The output power of 120 GHz LO was measured to 6.6 dBm.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.118-123
• /
• 2009

This paper discusses the design and fabrication of a reference signal generator for a naval radar system, including the vibration environment test. The transmit signals of the S-band radar system are synthesized by the reference signal and the phase noise must lower than - 130 dBc/Hz at a 10 kHz offset frequency. To achieve this specification, the phase noise of the reference signal needs to be less than -165 dBc/Hz at a 10 kHz offset. For achieving very low phase noise performance by the reference signal generator, the phase locked loop technique is applied with a 10 Hz loop bandwidth. Also, this reference signal generator has ${\pm}0.35\;ppb$ short-term stability to minimize instant phase errors and high vibration sensitivity against a ship's shaking, unbalanced rotating of antennas and so on.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.550-557
• /
• 2003

In this paper, two dualband internal antennas for GPS/PCS handset are proposed. At first, the monopole antenna with parasitic dipole element is designed to print PCB of handset directly. At second, the antenna with bended loop structure is designed to bend to use internal space of handset maximumly. The proposed dualband internal antennas provide a 2:1 VSWR bandwidth of over 19.1 % which are possible to cover two bands at once. the antennas have a gain between -0.4 and 3.33 ㏈i at all bands and they have almost omni-directional patterns.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.10
• /
• pp.1110-1118
• /
• 2012

In this study, for reducing the residual vibration in high speed motion control stage, an improved 5th order polynomial motion profile was developed. When a stage is moving, the current through the motor coils has the same profile of input motion profile of acceleration, therefore the characteristics of the acceleration input profile directly affect on the performance of the amplifier that includes the current control loop. Commonly low cost amplifier and motor has a narrow current control bandwidth, therefore the proposed algorithm was designed based on this practical constraint. Simulation and experimental results showed that the proposed algorithm clearly has low residual vibration characteristics than conventional 5th order polynomial motion profile on the same drive condition.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.7
• /
• pp.513-518
• /
• 2016

The piezoelectric actuating device is known for its large power density and simple structure. It can generate a larger force than a conventional actuator and has also wide bandwidth with fast response in a compact size. To control the piezoelectric actuator, we need an analog signal conditioning circuit as well as digital microcontrollers. Conventional microcontrollers are not equipped with an analog part and need digital-to-analog converters, which makes the system bulky compared with the small size of piezoelectric devices. To overcome these weaknesses, we are developing a single-chip controller that can handle analog and digital signals simultaneously using mixed-signal FPGA technology. This gives more flexibility than traditional fixed-function microcontrollers, and the control speed can be increased greatly due to the parallel processing characteristics of the FPGA. In this paper, we developed a floating-point multiplier, PWM generator, 80-kHz power control loop, and 1-kHz position feedback control loop using a single mixed-signal FPGA. It takes only 50 ns for single floating-point multiplication. The PWM generator gives two outputs to control the charging and discharging of the high-voltage output capacitor. Through experimentation and simulation, it is demonstrated that the designed control loops work properly in a real environment.