• Journal of Pharmaceutical Investigation
• /
• 제36권5호
• /
• pp.331-338
• /
• 2006

A rapid, selective and sensitive reverse-phase HPLC methods for the determination of atenolol and chlorthalidone in human serum and whole blood were validated, and applied to the pharmacokinetic study of atenolol and chlorthalidone combination therapy. Atenolol and an internal standard, pindolol, were extracted from human serum by liquid-liquid extraction, and analyzed on a $\mu$-Bondapak C18 $10-{\mu}$ column in a mobile phase of methanol-0.01 M potassium dihydrogenphosphate(30:70, v/v, adjusted to pH 3.5) and fluorescence detection(emission: 300 nm, excitation: 224 nm). Chlorthalidone and an internal standard, probenecid, were extracted form human whole blood by liquid-liquid extraction, and analyzed on a Luna C18 $5-{\mu}$ column in a mobile phase of acetonitrile containing 77% 0.01 M sodium acetate and UV detection at 214 nm. These analysis were performed at three different laboratories using the same quality control(QC) samples. The chromatograms showed good resolution, sensitivity, and no interference by human serum and whole blood, respectively. The methods showed linear responses over a concentration range of 10-1,000 ng/mL for atenolol and 0.05-20 ${\mu}g/mL$ for chlorthalidone, with correlation coefficients of greater than 0.999 at all the three laboratories. Intra- and inter-day assay precision and accuracy fulfilled international requirements. Stability studies(freeze-thaw, short-, long-term, extracted sample and stock solution) showed that atenolol and chlorthalidone were stable. The lower limit of quantitation of atenolol and chlorthalidone were 10 ng/mL and 0.05 ${\mu}g/mL$, respectively, which was sensitive enough for pharmacokinetic studies. These methods were applied to the pharmacokinetic study of atenolol and chlorthalidone in human volunteers following a single oral administration of Hyundai $Tenoretic^{\circledR}$ tablet(atenolol 50 mg and chlorthalidone 12.5 mg) at three different laboratories.

• Journal of Radiation Protection and Research
• /
• 제37권3호
• /
• pp.149-158
• /
• 2012

알파, 베타핵종의 분리측정에 효과적인 저준위 액체섬광계수기를 이용하여 부산 금정구의 10지점을 선정하여 1년 동안 지하수 내 라돈농도의 변화를 측정하였다. 액체섬광계수기의 최적화된 측정방법을 결정하기 위하여 라듐-226의 표준선원을 이용하여 효율과 백그라운드의 관계를 나타내는 FM (Figure of Merit) 값이 최대가 되는 PSA 준위가 100에서 110범위에 있음을 확인하였다. 결정된 PSA 준위에서 측정된 부산 금정구 지역의 각 암석 분포에 대한 지하수 내 라돈의 평균 농도를 비교해보면, 흑운모화강암 지역은 191.39 $Bq{\cdot}L^{-1}$, 미문상화강암 지역은 141.88 $Bq{\cdot}L^{-1}$, 아다멜라이트 지역은 92.94 $Bq{\cdot}L^{-1}$, 안산암 지역은 35.35 $Bq{\cdot}L^{-1}$ 순으로 나타났다. 조사지역의 10개 지점에서 1년간 정기적으로 측정된 라돈농도의 변화 양상을 살펴보면, 뚜렷하게 구분되는 특징적 계절적 변화양상이 나타나지 않고 있다. 지하수 내 라돈 농도와 수온, 기온, 대기압, 강수량의 상관성을 알아본 결과 각각에 대한 뚜렷한 연관성은 찾을 수 없었으며, 하나의 변수에 대해서가 아니라 보다 복합적 요인과 작용에 의해 변화한다고 판단된다.

• Bulletin of the Korean Chemical Society
• /
• 제7권5호
• /
• pp.367-371
• /
• 1986

Dynamic and equilibrium properties of n-alkane chains immersed in solvent molecules have been investigated by a molecular dynamics method. The n-alkane chain is assumed to be a chain of elements (CH$_2$) interconnected by bonds having a fixed bond length and bond angle, but each bond of the chain is allowed to execute hindered internal rotation. We studied the effect of the number of the chain elements (N$_c$ = 10, 15 and 20) on the equilibrium properties of the system, e.g., the pair correlation functions between a chain element and solvent molecules, g$_{cs}$(r), and between the chain elements, g$_{cc}$(r), and the configurational properties such as the mean-square end-to-end distance < R$^2$ >, the mean-square radius of gyration < S$^2$ >, and the eigenvalues of the moment-of-inertia tensor < S$_i^2$ > / < S$^2$ > (i = 1, 2 and 3). We also studied the dynamic properties of the system, e.g., the autocorrelation function C(A;t) where A = R$^2$(t), = S$^2$(t), or = ${\vec{V}}(t)({\vec{V}}$ = velocity of the center of mass), and the diffusion coefficient D. The g$_{cs}$(r)'s are almost equal irrespective of the change of Nc while g$_{cc}$(r) becomes larger as N$_c$ increases; The MD computed configurational properties < R$^2$2 > and < S$^2$ > were found to be a little different from the values calculated from the statistical equations of < R$^2$ > and < S$^2$ >, it may be due to the fact that our model for the MD simulations includes a long-range volume effect. From the < S$_i^2$ > / < S$^2$ >, it is found that the chain molecule has a nearly spherical shape irrespective of the variation of N$_c$. For the dynamic properties we found that the C(R$^2$;t) and C(S$^2$;t) of lower N$_c$ decay faster than those of higher N$_c$, while the C($\vec V$;t) of the center of mass in the chain is weakly dependent on the N$_c$. The center of mass diffusion coefficient D$_c$ decreases as N$_c$ increases while the end point diffusion coefficient D$_e$ is nearly equal irrespective of the change of N$_c$.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 한국자원식물학회지
• /
• 제27권1호
• /
• pp.80-88
• /
• 2014

유채는 겨울철 유휴지와 하천부지 등의 효율적인 이용과 환경보호 측면에서 이모작이 가능하다는 장점이 있고, 보리수매제도 폐지로 인한 농가 소득 보전을 위한 대체 가능성이 크다. 이에 국산장려 품종인 선망, 탐미유채, 탐라유채, 내한유채, 한라유채, 영산유채를 이용 파종시기를 달리하여 각 품종의 수량과 개화지속기간을 구명하여 바이오에너지 원료확보 및 경관용으로서의 효율을 극대화하고자 본 실험을 수행하였다. 유채 품종별 파종시기 및 주요 수량구성요소, 종실수량의 분산분석 결과 파종시기와 품종의 효과는 천립중을 제외한 모든 조사형질에서 고도의 유의성이 인정되었고, 파종시기와 품종의 상호작용은 입모주수, 경장, 종실중과 고도의 유의성을 보였으며 협수와 천립중과는 p < 0.05 수준의 유의성이 인정되었다. 수량구성 요소인 경장과 협수, 결실립수 등은 수량을 증가시키는 요인이기 때문에 $m^2$당 입모수가 많고 이들 수량구성요소의 발현이 높게 하는 것이 효과적이다. 본 실험의 종실중은 역시 어느 품종을 막론하고 파종기가 늦어지면 늦어질수록 거의 직선적으로 감소하는 경향을 나타내었다. 이와 같은 이유는 파종기가 빠를수록 협수가 많아져 source의 경합이 컸었음에 기인하는 것으로 종실중은 천립중 보다는 결실립수를 결정하는 주당 협수에 의하여 가장 크게 좌우된다고 생각된다. Schukking (1984)은 유채는 재식밀도가 좁아짐에 따라 유채의 개화기까지의 일수가 늦어지고, 총 분지수, 엽수 등의 형질은 왜소해진다고 하여 파종기 변화에 따른 재식밀도에 대한 추가적인 구명도 해야 할 것이다. 한편으로 적절한 파종시기의 선택은 입모수가 많은 밀식상태이고 영양생장기간이 길어지므로 자연적으로 수량구성요소의 생육상황이 좋아지는 것으로 생각된다. 이러한 결과를 보면 무안지역에 있어서 유채 종자 채종을 위한 파종 적기는 10월 5일 이전으로 판단되는데 파종기가 늦어질 경우 영양생장기간이 짧아지기 때문에 생육일수의 단축에 의하여 유묘의 건조, 하고 현상 등의 문제점이 발생되어 수량구성요소가 감소되기 때문에 재식밀도의 변화를 준다면 수량감소 요인을 줄일 수 있을 것이라 생각된다. 한편 유채품종 별 개화지속일수는 9월 25일 파종의 경우 선망 > 탐미유채 > 영산유채 > 내한유채 > 한라유채 > 탐라유채 순 이였고, 파종일이 빠를수록 품종 간 개화기 차이가 뚜렷함을 확인하였으며 파종일이 늦을 경우 품종 간 개화기 차이는 거의 없었다. 경관효율을 극대화하기 위해서는 선망, 탐미, 영산 유채 등을 9월 25일 조기파종하고 탐라, 내한유채를 파종기를 달리하여 파종하였을 경우 최대 4월 3일부터 5월 14일까지 유채꽃을 관상할 수 있었다. 전체적으로 파종일 차이에 따라 각 품종별로 약 1~14일 정도 개화지속일수차이를 보였으며, 개화종기에 비해 약 2~9일 정도 개화기를 연장 할 수 있었다. 본 실험의 결과 중생종과 만생종인 한라, 내한, 탐라유채에 보다는 조생종의 특성을 보이는 선망, 탐미, 영산유채 품종을 축제기간에 맞춰 파종시기를 조절한다면 축제기간에 꽃이 피지 않아 발생하는 고민을 일정부분 해결할 수 있을 것이라 판단된다.

• 한국지구과학회지
• /
• 제35권1호
• /
• pp.1-18
• /
• 2014

이 연구의 목적은 2008년 5월 29일 우리나라에 영향을 미치는 황사를 예측하기 위해 WRF-Chem 모델 내 에어로졸 스킴과 광물성 먼지 옵션에 따른 미세먼지 농도 변화와 그에 따른 기상장의 민감도를 분석하는 것이다. 미세먼지의 인위적 배출량에 대해서는 $0.5^{\circ}{\pm}0.5^{\circ}$ RETRO 전구 배출량을, 광해리의 경우 Fast-J 광해리 스킴을, 그리고 황사 발생량을 추정하기 위해 RADM2 화학메커니즘 및 MADE/SORGAM 에어로졸 시나리오, MOSAIC 8 섹션 에어로졸 시나리오, 그리고 GOCART 먼지 침식 시나리오를 각각 적용하였다. 그 결과 RADM2 화학메커니즘 및 MADE/SORGAM 에어로졸 시나리오가 다른 시나리오들보다 우리나라 황사 먼지 농도와 배경 PM 농도를 더 높게 모사하였다. 그리고 이 시나리오와 서울의 각 대기질 측정망의 평균 PM10 농도와의 비교 결과, 상관계수는 0.67, 평균제곱근오차는 $44{\mu}gm^{-3}$으로 나타났다. 또한 WRF-Chem 모델에서 상기 3가지 시나리오와 이들 시나리오가 없는 순수 기상에서의 온도, 풍속, 경계층 높이, 장파복사의 기상 민감도를 분석한 결과, 1,800-3,000 m 경계층 높이와 $2-16ms^{-1}$ 풍속 U 성분의 공간적 분포가 황사 먼지 발생의 공간적 분포와 유사하게 나타났다. 그리고 GOCART 먼지 침식 시나리오와 RADM2 화학메커니즘 및 MADE/SORGAM 에어로졸 시나리오는 황사 먼지 또는 에어로졸과 기상이 온라인으로 상호작용함으로써 지구장파복사가 더 낮게 모사되었다.

• 미생물학회지
• /
• 제17권3호
• /
• pp.97-130
• /
• 1979

Many industrial processes those employ bacteria are subjected to phage infestations. In L-glutamic acid fermentions using acetic acid, the phage infestations of the organisms have been recently recognized. In efforts to elucidate the sources of phage contamination involved in the abnormal fermentation, a series of study was conducted to isolate the phages both from the contents of abnormally fermented tanks and the soil or sewage samples from the surroundings of a fermentation factory, to define major charateristics of the phage isolates, and finally to determine the correlation between the phage isolates and temperate phages originating from the miscellaneous bacterial species isolated from the soil or sewage samples. The results are summarized as follows; 1) All phages were isolated from the irregular fermentation tanks and soil or sewage samples, and they were designated as phage PR-1, PR-2, PR-3, PR-4, PR-5, PR-6, and PR-7, in the order of isolation. These PR-series phages were proved to be highly specific for the variant strains of Br. lactofermentum only, namely, phage PR-1 and PR-2 for Br. lactofermentum No. 468-5 and phage PR-3~PR-7 for Br. lactofemrentum No. 2256. By cross-neutralization test, the 7 phagescould be subdivided into 3 groups, i. e., phage PR-I and PR-2 the first, phage PR-3, PR-4, PR-5, PR-6 the second, and the phage PR-7 the third. 2) The 7 phages were virulent under the experimental conditions. They produced plaques with clear and relatively sharp margins without distinct halo. The mean sizes of plaques were 1.5mm in diameter for phage PR-1 and PR-2, and 1. Omm for phages PR-3~PR-7. Double layer technique modified by Hongo and described by Adams, was applied to assay of the PR-series phages. The factors influencing the plaques were as follows;young age cells of host bacteria cultured for 3-6 hours represented the largest number and size, optimum was pH 7.0, incubation temperature was $30^{\circ}C$, and agar concentration and amount of overlayer medium were 0.6% and 0.2ml, respectively. 3) PR-series phages were stable in 0.05M tris buffer and 0.1M ammonium acetate buffer solution. The addition of $5{\times}10^{-3}M$ magnesium ion effectively increased the stability. Thermostability experiments indicated that PR-series phages were stable at the teinperture between $50^{\circ}{\sim}55^{\circ}C$ in nutrient medium, $45^{\circ}{\sim}50^{\circ}C$ in buffer solution. However, the phages mere completely inactivated at 603C and 65$^{\circ}$C within 10 minutes. The phages were stable at the range of pH6~9 in nutrient medium and of pH 8-9 in buffer solution, respectively. Exposure of the phages to UV for 25, 60 and 100 seconds resulted in the complete loss of infectivily, respectively. 4) Electron microscopy showed that PR-series phage particles exhibited rather similar morphology, differing in the size All of PR-series phages had a multilateral head and had a simple long tiil about three to five times long as compared with head. By the size, phage PR-1 and PR-2, PR-3, PR-4, PR-5, and PR-6 and PR-7 were classified into same groups, respectively. The head and tail size of phage PR-1, PR-5, PR-5(T) and PR-7 were 85nm, 74nm and 235nm and 350mm, and 72nm and 210nm, respectively. 5) Nucleic acids of PR-series phages were double stranded DNA. The G+C contents of phage PR-1, PR-5 and PR-7 were 56.1, 52.9 and 53.7, respectively. The values of G+C contents derived from the $T_m$ were in agreement with the chemically determined values. 6) PR-series phages effectively adsorbed on their host bacteria at the rate of more than 90% during 5 min. K value for phage PR-1, PR-5 and PR-7 were calculated to be $6{\times}10^9 ml$ per minute, respectiveky. The pH of the medium did effect adsorption rate, but both temperature and age of host cells did not. Generally, optimum adsorption condition of phages seemed to be almost same as optimum growth conditions of host bacteria. 7) In one-step growth experiments, the latent periods at $30^{\circ}C$ for PR-1, and PR-7 were about 70, 50 and 55 min, respectively. The corresponding average burst size was 200, 70 and 90, respectively. Lpsis period according to the multiplicity of infection and a phage series. In case of m. o. i. 100, strain No. 2256 (PR-5) and No. 468-5(PR-1) failed to grow and turbidity decreased after 50 and 70min, respectively. 8) In the lysate of a plaque purified phage PR-5 infected bacteria, there observed 2 types ofphage particles, i. e., phage PR-5 and PR-5 (T) of similar morphology but differing at the length of phage tail, and phage tail like particles. The phage taillike particles could be divided into 4 types by the length. Induction experiments of Br. lactofermentum with UV irradiation, mitomycin C or bacitracin treatment produced neither phage PR-5 (T) or phage tail-like particles. 9) No lysis occured when the growth of 7 strains of miscellaneous bacteria, isolated from soil and sewage samples, were inoculated with either phage PR-5 (T) or phage tail-like particles the inoculation of phage PR-5 pellet resulted in the growth inhibition of the orgainsms in the spot test. The lysates obtained from 3 miscellaneous soil derived bacteria following mitomycin C treatment the growth of Br. lactofermentum, but did not lyze the bacterium.

• 대한토목학회논문집
• /
• 제30권3A호
• /
• pp.297-307
• /
• 2010

최근 토목, 건축 구조물의 유지관리 기술에 대한 관심이 커지고 있으며 구조물의 성능저하 및 노후화 등으로 구조적 안전성의 검토가 요구되는 구조물의 수가 급증하고 있는 실정이다. 그리고 구조물의 노후화 및 부재의 균열 등으로 인하여 강성이 저하되면 구조물의 동특성에 변화가 나타나게 되며 구조물의 실제 거동상태에서 동특성을 분석하여 손상부위와 손상정도를 정확히 판단하는 것은 중요한 문제이다. 구조물 모니터링에 사용되는 대표적 계측장비가 동적계측기이다. 기존의 동적계측기는 측정 센서와 장비를 연결하는 케이블 길이가 길어질 경우 신뢰할 수 있는 데이터를 얻기 힘들고 각 센서와 계측기를 1:1로 연결하는 방식을 취하고 있어 비경제적이다. 따라서 센서를 부착하지 않고 원거리에서 진동을 측정하는 방법이 필요하다. 구조물의 진동을 계측하기 위하여 적용 가능한 비접촉식 방법으로는 레이저의 도플러효과, GPS를 이용하는 방법 및 영상처리기법 등이 대표적이다. 레이저의 도플러효과를 이용하는 방법은 정확도가 상대적으로 높지만 비경제적이며, GPS를 이용하는 방법은 장비가 고가이고 신호 자체의 오차와 데이터 취득속도의 제약이 있는 단점이 있다. 그러나 영상신호를 이용하는 방법은 간편하고 경제적이며 접근이 어려운 구조물의 진동 및 동특성 추출에 적합하다. 기존에도 센서를 대신하여 카메라의 영상신호를 이용하는 연구가 수행되기도 하였으나, 기존의 방법은 구조물에 부착된 표적의 한 지점을 기록한 후 영상처리기법을 이용하여 진동을 측정하는 방법으로서 측정 대상이 비교적 국한적일 수 있다. 그러므로 본 연구에서는 영상처리기법을 이용하여 구조물의 다중 변위응답을 측정할 수 있는 방법의 타당성을 검증하기 위하여 진동대 실험 및 현장재하실험을 수행하였다.

• 대한정형외과스포츠의학회지
• /
• 제4권1호
• /
• pp.18-28
• /
• 2005

목적: 퇴행성 슬관절염 환자에서 관절경을 이용한 미세 천공술 후 재생된 연골의 임상적, 방사선학적 그리고 조직병리학적 결과를 분석하고자 한다. 대상 및 방법: 1997년 10월부터 1998년 12월까지 관절경을 이용한 미세 천공술로 치료한 퇴행성 슬관절염 환자 46명, 48례를 대상으로 하였으며, 평균 연령은 56세이었고 평균 추시기간은 1년이었다. 이차관절경술은 수술 후 6개월에 22명, 24례에서 시행하였다. 임상적 평가는 최종추시 시에 Baumgaertner의 슬관절 기능 평가 방법에 의해 시행하였다. 이차관절경술을 시행한 24례에서 일반 조직학적 검사를 시행하였고 제2형 교원질의 존재를 확인하기 위하여 18례에서는 면역 조직화학적 검사를 시행하였으며 12례에서는 Western blotting test를 시행하였다. 정량화된 제2형 교원질의 양에 따라 세군으로 나누고 임상적, 방사선학적, 이차관절경 소견, 환자의 나이 그리고 체중과의 상관관계를 분석하였다. 결과: 임상적 결과는 43례(90%)에서 우수, 5례(10%)에서 양호의 결과를 보였다. 이차관절경술을 시행한 24례중 21례에서 연골결손 부위의 80%이상이 재생된 연골로 덮혀 있는 것을 확인할 수 있었으며, 재생된 연골은 조직학적으로 초자연골과 섬유연골로 이루어진 혼합형 연골이었다. 면역 조직화학적 검사 및 Western blotting test결과상 정도의 차이는 있었지만 전례에서 제2형 교원질의 존재를 확인할 수 있었다. 정량화된 제2형 교원질의 양이 많을수록 수술 전 내반변형의 정도는 적었고 이차관절경소견상 재생된 연골의 범위가 넓었으며 이는 통계학적으로 유의한 차이를 보였다. 요약 및 결론: 퇴행성 슬관절염 환자에서 관절경을 이용한 미세 천공술은 연골 결손 치료에 있어 유용한 치료방법으로 사료되며 이러한 재생된 연골이 지속적인 체중 부하에 의해서 생역학적인 변화를 일으키지 않고 얼마나 유지 할 수 있는지는 보다 장기적인 추시 관찰이 필요할 것으로 사료된다.