• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1614-1617
• /
• 2003

Actuator being used in the ship supplies engine with air. When actuator is out of order, engine is not operated. This out of order is due to fracture of piston or rotating of spindle in the case of plastic deformation of parallel part in locking plate. For this reason, locking plate must be guaranteed enough strength. Therefor in this paper, the effects of changes with the clearance of between spindle and parallel part, the contact height of parallel part and spindle, the side circle diameter of parallel part and the width of locking plate in the designated torque are investigated. The result of this investigation shows the relation between locking plate and spindle.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.9
• /
• pp.2362-2372
• /
• 1996

This paper deals with the design and development of an Injection-Locking Coupled Oscillators(ILCO), which functions like phase-shifter in the Active Intergrated Phased Array Antenna(AIPAA). This linear array 2-element ILCO consists of two Injection Locking Hair-pin Resonator Oscillators(ILHRO) and an unilateral amplifier. The first and second elements of the ILCO have same frequency tuning range but locking bandwidths of 11.5MHz and 14MHz respectively. A phase shift of .DELTA..PHI.=158.4.deg.(-78.0.deg. to 80.4.deg.) could be obtained inthe second element of ILCO when the first elementof the ILCO was in the reference locking mode(.DELTA..PHI.=0.deg.). When the ILCO is applied to the AIPAA, the predicted beam scanning angle value will be 38.4.deg.. Each ILCO gives good frequency stability and lower AM, FM, and PM noise charactheristics in the mutual coupling lockingmode. The ILCO can not only play a part as the phase shifter for the AIPAA but it can also be usedas the power combining device in the mm-wave frequency range and as a part of a T/R MMIC module.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.6
• /
• pp.121-126
• /
• 2006

Snap-fit is being used in manufacture of plastic products. Integral features using snap-fit are classified as locks, locators and enhancements. Locking features complete the process of attachment by providing physical interference to prevent separation. Looking feature pairs consist of two components, i.e., a flexible latch and a rigid catch and require particular care and attention for their selection. We can make several locking feature pairs by selecting latch and catch, but some parts restrict freedom of selection. Therefore, part designers must know the characteristic properties of generic locking feature forms as considering a specific design problem. In this paper, it has been presented about problem of small size products using locking feature and then introduced new locking feature applicable to small parts.

• Nuclear Engineering and Technology
• /
• v.55 no.12
• /
• pp.4477-4490
• /
• 2023

Fuel locking mechanisms (FLMs) are essential in upward-flow research reactors to prevent accidental fuel separation from the core during reactor operation. This study presents a novel design concept for a remotely controlled plate-type nuclear fuel locking mechanism. By employing electromagnetic field analysis, we optimized the design of the electromagnet for fuel unlocking, allowing the FLM to adapt to various research reactor core designs, minimizing installation space, and reducing maintenance efforts. Computational flow analysis quantified the drag acting on the fuel assembly caused by coolant upflow. Subsequently, we performed finite element analysis and evaluated the structural integrity of the FLM based on the ASME boiler and pressure vessel (B&PV) code, considering design loads such as dead weight and flow drag. Our findings confirm that the new FLM design provides sufficient margins to withstand the specified loads. We fabricated a prototype comprising the driving part, a simplified moving part, and a dummy fuel assembly. Through basic operational tests on the assembled components, we verified that the manufactured products meet the performance requirements. This remote-controlled micro locking mechanism holds promise in enhancing the safety and efficiency of plate-type nuclear fuel operation in upflow research reactors.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.2
• /
• pp.38-50
• /
• 1982

A new type of digital phase-locked loop (DPLL) called the modified digital Costas loop is proposed and analyzed. The main feature of the proposed loop is that the phase error detector of the loop has linear characteristic. This results from the use of the tan-1 (.) function in the loop. Accordingly, the DPLL can be characterized by a modulo-2$\pi$ linear difference equation. This paper is diveide into two parts. In Part I we describe the proposed system, and analyze the performance of the first-and second-order loops in the absence of noise by the Phase Plane technique. The locking ranges for the DPLL's to achieve exact locking independently of initial conditions have been obtained in closed forms. Also, the false lock and oscillation phenomena occurring under some initial conditions have been considered. These results have been verified by computer simulation. In Part ll we analyze the proposed system in the presence of noise. The steady state probability density function, mean and variance of the phase error have been obtained by solving the Chapman-Kolmogorov equation. These results will be presented in Part ll.

• Clinics in Shoulder and Elbow
• /
• v.17 no.1
• /
• pp.10-17
• /
• 2014

Background: The aim of this study was to assess the clinical outcomes after treatment of proximal humeral fractures with locking plates, and to determine which factors influence the clinical and radiological outcomes. Methods: Fifty six patients who were treated with locking plates for proximal humeral fractures and had been followed for more than 1 year were enrolled in this study. We performed functional evaluation using the Constant score and analyzed radiographic results. The following factors that may potentially influence the clinical outcomes were assessed: age, gender, type of fracture, presence of medial metaphyseal comminution, bone mineral density, anatomical reduction, restoration of medial mechanical support, and postoperative complications. Results: The mean Constant score was 70.1 points at the final follow-up. Female gender, 4-part fractures, AO type-C fractures, and fractures with medial metaphyseal comminution were associated with a poor clinical outcome. On the other hand, restoration of medial mechanical support and accurate anatomical reduction had a positive influence on clinical outcomes. Postoperative complications resulted in 3 patients (intra-articular screw perforation: 1 patient, varus deformity with screw loosening: 1 patient, nonunion: 1 patient). Conclusions: When treating proximal humeral fractures with locking plate fixation, following factors: a female gender, Neer type 4-part fracture, AO type C fracture, and medial metaphyseal comminution are important risk factors that surgeons should take into consideration. Factors that contribute to better clinical outcomes of operative treatment for humeral fractures are accurate anatomical reduction and restoration of medial mechanical support.

• The KIPS Transactions:PartD
• /
• v.8D no.1
• /
• pp.24-31
• /
• 2001

In this paper, we present an advanced transaction scheduling protocol to improve the degree of concurrency and satisfy the security requirements for multilevel secure database. We adapted two-phase locking protocol, namely traditional syntax-oriented serializability notions, to multilevel secure database. Altruistic locking, as an advanced protocol, has attempted to reduce delay effect associated with lock release moment by use of the idea of donation. An improved form of altruism has also been deployed for extended altruistic locking OffiLl. This is in a way that scope of data to be early released is enlarged to include even data initially not intended to be donated. We also adapted XAL to multilevel secure database and we first of all investigated limitations inherent in both altruistic schemes from the perspective of alleviating starvation occasions for transactions in particular of short-lived nature for multilevel secure database. Our protocol is based on extended altruistic locking for multilevel secure database (XAL/MLS), but a new method, namely two-way donation locking for multilevel secure database (2DL!/-MLS), is additionally used in order to satisfy security requirements and concurrency. The efficiency of the proposed protocol was verified by experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1131-1135
• /
• 2005

Since human is vulnerable to emotional, physical and environmental distractions, most human inspectors cannot sustain a consistent 8-hour inspection in a day specifically for small components like door locking levers. As an alternative for human inspection, presented in this study is the development of a machine vision inspection system (MVIS) purposely for door locking levers. Comprises the development is the structure of the MVIS components, designed to meet the demands, features and specifications of door locking lever manufacturing companies in increasing their production throughput upon keeping the quality assured. This computer-based MVIS is designed to perform quality measures of detecting missing portions and defects like burr on every door locking lever. NI Vision Builder software for Automatic Inspection (AI) is found to be the optimum solution in configuring the needed quality measures. The proposed software has measurement techniques such as edge detecting and pattern-matching which are capable of gauging, detecting missing portion and checking alignment. Furthermore, this study exemplifies the incorporation of the optimized NI Builder inspection environment to the pre-inspection and post-inspection subsystems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1558-1563
• /
• 2010

This paper describes a study on algorithm for the development of machine vision system as well as the inspection of automobile's plastic part locking lever to replace a human worker's eye inspection. Before developing the machine vision system based on the PC, the purpose of this research is to develop the algorithm to decide whether a product is a good/bad one in real time inspection. NI-LabVIEW software is used in the inspection method and an inspection program is developed using LabVIEW Vision image functions. The inspection program was built and validated to help the system operator set up the inspection area and change the criteria number in the program.

• Clinics in Shoulder and Elbow
• /
• v.21 no.4
• /
• pp.220-226
• /
• 2018

Background: This study introduces a surgical technique with good clinical outcome useful in the treatment of osteoporotic displaced 3- or 4-part proximal humeral fractures. Methods: From May 2014 to February 2016, 16 patients with displaced 3- or 4-part proximal humeral fractures were treated by application of a locking plate with an endosteal strut allograft via a deltoid splitting approach with a minimum follow-up of 12 months. The allograft was inserted through a fractured gap of the greater tuberosity to support the humeral head and then fixed by a locking plate with meticulous soft tissue dissection to protect the axillary nerve. Surgical outcomes were evaluated by the American Shoulder and Elbow Surgeons (ASES) and visual analogue scale (VAS) scores, radiological imaging, and clinical examination. Fixation failure on radiographs was defined as a >$5^{\circ}$ loss of neck shaft angle (NSA) compared to that on an immediate postoperative radiograph. Avascular necrosis (AVN) of the humeral head was also evaluated. Results: In all cases, complete union was achieved. The ASES and VAS scores were improved to $85.4{\pm}2.1$ and $3.2{\pm}1.3$, respectively. Twelve patients (75.0%) had greater than a $5^{\circ}$ change in NSA; the average NSA change was $3.8^{\circ}$. Five patients (31.3%) had unsatisfactory ranges of motion exhibiting a <$100^{\circ}$ active forward flexion. No axillary nerve injuries or AVN were observed at the last follow-up. One patient was converted to reverse total arthroplasty due to severe pain and functional deficit. Conclusions: Minimally invasive fixation via a locking compression plate and an endosteal fibula strut allograft in Neer classification 3-or 4-part fractures with severe osteoporosis in elderly patients can achieve good clinical results.