• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4C
• /
• pp.191-196
• /
• 2011

In this paper, we propose a design method of Reed-Solomon (23, 17) decoder for UWB using direct decoding method. The direct decoding algorithm is more efficient for the case of relatively small error correction capability. The proposed decoder requires only 9 $GF(2^m)$ multipliers in obtaining the error-locator polynomial and the error-evaluator polynomial, whereas other decoders need about 20 multipliers. Thus, the attractive feature of this decoder is its remarkable simplicity from the point of view of hardware implementation. Futhermore, the proposed decoder has very simple control circuit and short decoding delay. Therefore this decoder can be implemented by simple hardware and also save buffer memory which stores received sequence.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.1
• /
• pp.28-37
• /
• 2016

Fault locating is an important element to minimize the damage of power system. The computation error of fault locator may occur by the influence of the DC offset component during phasor extraction. In order to minimize the bad effects of DC offset component, this paper presents an improved fault location algorithm based on a DC offset removal filter for short fault in a double circuit transmission line. We have modeled a 154kV double circuit transmission line by the ATP software to demonstrate the effectiveness of the proposed fault locating algorithm. The line to line short faults were simulated and then collected simulation data was used. It can be seen that the error rate of fault locating estimation by the proposed algorithm decreases than the error rate of fault locating estimation by conventional algorithm.

• The Journal of Engineering Research
• /
• v.6 no.2
• /
• pp.125-130
• /
• 2004

In the current Internet, IP addresses does not support Mobility and Multi-homming because it depend on their topological location. To resolve these problems, IETF hip WG introduces Host Identity Protocol that separates the endpoint identifier and locator roles of IP addresses. However the DNS that was presented for the HIP had only a part of the expansion design from the existing DNS function, so it was not an absolute complete method. This paper propose how the dymanic DNS has been designed so that it support the HIP completely. We added the Host Identity Namespace and the Rendezvous Server Namespace, defined the new PRs in DNS.

• Restorative Dentistry and Endodontics
• /
• v.46 no.1
• /
• pp.12.1-12.9
• /
• 2021

Objectives: The present study aims to compare the obturation quality of 2 confluence confirmation techniques in artificial maxillary first premolars showing Vertucci type II root canal configuration. Materials and Methods: Thirty artificial maxillary premolars having Vertucci type II root canal configuration were made. They were divided into 3 groups according to the confluence confirmation technique as follows. Gutta-percha indentation (GPI) group (confluence confirmation using a gutta-percha cone and a K file); electronic apex locator (EAL) group (confluence confirmation using K files and EAL); and no confluence detection (NCD) group. In the GPI group and the EAL group, shaping and obturation were performed with the modified working length (WL). In the NCD group, shaping was performed without WL adjustment and obturation was carried out with an adjusted master cone. Micro-computed tomography was used before preparation and after obturation to calculate the percentage of gutta-percha occupied volume (%GPv) and the volume increase in the apical 4 mm. Data were analyzed using 1-way analysis of variance and post hoc Tukey's test. Results: Statistically significant difference was not found in terms of the %GPv from the apex to apical 4 mm. However, the NCD group showed a statistically significant volume increase compared with the EAL group (p < 0.05). Conclusions: In terms of gutta-percha occupied volume, no significant difference was observed among the 3 groups. Confluence confirmation using an EAL in teeth with Vertucci type II configuration showed less volume increase during canal shaping compared with no confluence confirmation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.1
• /
• pp.91-104
• /
• 2008

Recently, osseointegrated implants have been used to improve denture support, stability, and retention. Several studies have been revealed that mandibular two-implant overdentures significantly increase patient satisfaction with the function of their prostheses. Use of a wide variety of attachment systems, including stud, magnet, and bar attachments, has proven both clinically predictable and effective. This article presents that two-implant overdenture can become the standard of care for treatment of the edentulous mandible.

• The Journal of Korean Academy of Prosthodontics
• /
• v.14 no.1
• /
• pp.11-16
• /
• 1976

Casts are often transferred to the articulator by arbitrary means, because the method of locating the true hinge axis point thought to be a complicated and time consuming procedure, and because the importance and significance of the true hinge axis in the construction of dental prosthesis is not sufficiently understood. In this report, the author constructed the hinge axis locator and determined the variations in location of the true hinge axis points from the location of the hinge axis point determined by arbitrary means. For this report, the procedure was followed on 50 persons with normal occlusion and sound T.M.J. function, so 100 true hinge axis points were recorded and compared with the arbitrary hinge axis point. The results obtained were as follows. 1. The mean distance from the arbitrary hinge axis point to the true hinge axis point was as follows. Right; (O)5.17mm., (V)3.44mm., (H)3.55mm.. Left; (O)5.63mm., (V)3.95mm., (H)3.51mm.. 2. The percentage of true hinge axis points classified at intervals of 2mm was as follows. 0-2mm; 4%, 2-4mm; 21%, 4-6mm; 37%, 6-8mm; 26%, 8-10mm; 10%, Over 10mm; 2%. And only 50% of the 100 true hinge axis points were located within a 5mm. radius of the arbitrary hinge axis point. 3. Instead of transferring the casts to the articulator by arbitrary means, the careful location of the true hinge axis points is recommended to avoid potential sources of error in mounting casts.

• The Journal of Korean Academy of Prosthodontics
• /
• v.22 no.1
• /
• pp.72-78
• /
• 1984

The notion that the axis of the shaft of the articulator must coincide the patient's mandibular transverse axis tells us the importance of locating the axis precisely. When using kinematic axis to transfer a cast to an articulator, the anatomic asymmetry of the contralateral points will result in certain distortion when the axis transferred to an articulator where the mechanical axis produces symmetry. In this study, after locating the true hinge axis point with Denar hinge axis locator, the discrepancies between true hinge axis point and arbitrary hinge axis point that was 13mm anterior from the posterior margin of center of trangus to the outer canthus of eye were measured. And the discrepancies between left and right true hinge axis point in the superoinferior and anteroposterior directions were measured. For this study, 20 dental students who have no missing teeth and no difficulties of mandibular movement were selected. Upper and lower cast of subjects were mounted on Denar Mark II articulator uisng Denar Slidematic face-bow and centric relation record for the measurement of discrepancies between left and right true hinge axis points. The results obtained as follows. 1. The mean distance from the arbitrary hinge axis point to the true hinge axis point was as follows. Right: horizontal distance; 1.99mm, vertical distance; 2.12mm, linear distance; 3.36 mm. Left: horizontal distance; 1.39mm, vertical distance; 2.06mm, linear distance; 2.09mm. Total: horizontal distance; 1.69mm, vertical distance; 2.09mm linear distance; 3.06 mm. 2. The 87.5% of true hinge axis points were within 5mm of the arbitrary hinge axis point. 3. The mean discrepancies between the right and left hinge axis point were 2.92mm in superoinferior direction and 4.74mm in anteroposterior direction. 4. When transferring the axis to the articulator, anatomic asymmetry between right: and left axis point produces in dislocation of cast on the articulator, and undesirable shift in esthetic tooth position will be resulted.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.294-299
• /
• 2010

ELT(Emergency Locator Transmitter) is used to send distress signal in the event of an aircraft crash. It is very useful but the ELT may transmit wrong signal caused by misjudging between crash and hard-landing. The reason of this problem is the low accuracy of the mechanical G-switch currently in use. To improve the ELT, we developed an ELT system using the MEMS(Micro Electro-Mechanical Sensor) accelerometer. The ELT system consists of acceleration data acquisition/analysis system, program of crash recognition, and GPS receiving system for the position information of an aircraft crash site. A free-drop table was developed for verification of the ELT system. The free-drop table was designed to replicate the acceleration and the pulse duration of the hard landing and the crash. By using the free-drop table, we showed that the ELT system performed well.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.1
• /
• pp.59-65
• /
• 2004

Root perforations that result in a communication of the root space with the periodontal tissues occasionally occur during endodontic procedures. They may be induced iatrogenically. Successful treatment depends mainly on immediate sealing of the perforation and prevention of infection. Several factors affect the achievement of these goals, most important of which are time of occurrence, size and location of the perforation. Identification of root perforations is possible by direct observation of bleeding, radiography and an apex locator. Perforation defects may be repaired by nonsurgical or surgical techniques. We report two cases of root perforation. One was treated by glass ionomer, other was treated by composite resin with calcium hydroxide.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.10
• /
• pp.1495-1507
• /
• 1993

In this paper, an implementation of RS (Reed-Solomon) code decoder for CDP (Compact Disc Player) using microprogramming method is presented. In this decoding strategy, the equations composed of Newton's identities are used for computing the coefficients of the error locator polynomial and for checking the number of erasures in C2(outer code). Also, in C2 decoding the values of erasures are computed from syndromes and the results of C1(inner code) decoding. We pulled up the error correctability by correcting 4 erasures or less. The decoder contains an arithmetic logic unit over GF(28) for error correcting and a decoding controller with programming ROM, and also microinstructions. Microinstructions are used for an implementation of a decoding algorithm for RS code. As a result, it can be easily modified for upgrade or other applications by changing the programming ROM only. The decoder is implemented by the Logic Level Modeling of Verilog HDL. In the decoder, each microinstruction has 14 bits( = 1 word), and the size of the programming ROM is 360 words. The number of the maximum clock-cycle for decoding both C1 and C2 is 424.