• Journal of IKEEE
• /
• v.27 no.3
• /
• pp.355-367
• /
• 2023

Local Interconnect Network (LIN) is a low-speed in-vehicle network bus, and it is widely used in body applications such as windows, doors, HVAC, and lighting. This review explains protocols and message frames of LIN bus in detail. LIN bus basically transmits ID and payloads in data frame. How to interpret ID and payloads is defined in LIN Description file (LDF). Each LIN bus has unique LDF and its corresponding unique configuration. This review also explains syntax and example of LDF in detail.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.518-521
• /
• 2018

IVN (in-vehicle network) connects various electronic modules in the vehicles. It requires real-time, low noise, high reliability, and high flexibility. It includes CAN (controller area network), CAN-FD (CAN flexible data rate), FlexRay, LIN (local interconnect network), SENT (single edge nibble transmission), and PSI5 (peripheral sensor interface 5). In this paper, their operation priciples, target applications, and pros and cons are explained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.48-55
• /
• 2005

In this paper, a mathematical model and a simulation method for the response time analysis of Local Interconnect Network(LIN) based network systems are proposed. Network-induced delays in a network based control system can vary widely according to the transmission time of message and the overhead time of transmission. Therefore, in order to design a distributed control system using LIN network, a method to predict and verify the timing behavior of LIN protocol is required at the network design phase. Furthermore, a simulation environment based on a timing model of LIN protocol is beneficial to predict the timing behavior of LIN. The model equation is formulated with six timing parameters deduced from timing properties of LIN specification. Additionally, LIN conformance test equations to verify LIN device driver are derived with timing constraints of the parameters. The proposed model equation and simulation method are validated with a result that is measured at real LIN based network system.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.333-336
• /
• 2016

LIN (local interconnect network) is a standard low-speed serial communication protocol, and it was developed as an efficient sub-bus for automotive electronic modules. In this paper, a LIN controller was implemented in Verilog HDL, based on LIN ver. 2.2A. The implemented LIN controller was verified in FPGA, and it can be supplied as an IP to be integrated into SoC system. Its size is about 2,300 gates when synthesized in 0.18um technology.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.762-765
• /
• 2021

In this paper, an automotive ECU (electronic control unit) with Kalman filter accelerator is designed and implemented. RISC-V is exploited as a processor core. Accelerator for Kalman filter matrix operation, CAN (controller area network) controller for in-vehicle network, and LIN (local interconnect network) controller are designed and embedded. Kalman filter operation consists of time update process and measurement update process. Current state variable and its error covariance are estimated in time update process. Final values are corrected from input measurement data and Kalman gain in measurement update process. Usually floating-point multiplication is exploited in software implementation, but fixed-point multiplier considering accuracy analysis is exploited in this paper to reduce hardware area. In 28nm silicon fabrication, its operating frequency, area, and gate counts are 100MHz, 0.37mm², and 760k gates, respectively.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.5
• /
• pp.313-318
• /
• 2014

Recently, Ethernet-based Diagnostic Over Internet Protocol (DoIP) was applied to automotive systems, and in-vehicle gateways have been introduced to integrate Ethernet with traditional in-vehicle networks, such as the local interconnect network (LIN), controller area network (CAN) and FlexRay. The introduction of in-vehicle gateways and of Ethernet based diagnostic protocols not only decreases the complexity of the networks, but also reduces the update time for ECU software reprogramming while enabling the use of a range of services, including remote diagnostics. In this paper, a diagnostic gateway was implement for an automotive system, and the performance measurements are presented. In addition, a range of applications provided by the diagnostic gateway are proposed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3144-3153
• /
• 1996

ATM switching system is made up of transport network and control newrk according to its functions. The control device, basic part of control network must be developed before developing any other functions, and control device must be stable and need high reliability. Out distributed ATM switching system consists of several ALSs that provides variable local call services, and an ACS that interconnect among several ALSs. Eech ALS has CCCP that takes charage of call and connection control functions, and ACS has an OMP that takes charge of OA&M(Operation, Administration and Maintenance) functios. In this paper, we analyzed the performance evaluation of control device that manipulate subscriber's call based on ITU-T Q.2931 standard protocol messages and Interprocessor communication messages. As a result of simulation when the number of ALS is under 22, as the call arrival rate increase the processor utilization of CCCP increase rapidly than that of OMP. When the number of ALS is incremented to 22, the processor utilization of CCCP is balanced with the of OMP, and when the number of ALS exceeds 22, the processor utiliztion of OMP increase rapidly. Also if messary processing time of OMP is 1.35 times that of CCCP, processor utilizations of CCCP and OMP is equal.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.538-539
• /
• 2013

LIN(Local Interconnect Network) 통신은 CAN(Controller Area Network) 통신과 더불어 차량용 통신으로 많이 사용되고 있다. LIN 통신은 필요 성능의 수준이 높지 않은 장치 및 시스템이나 비용의 경제적인 측면에서 CAN 통신의 하부버스로 많이 사용되며 LIN 노드에 개수도 점차 늘어나고 있다. 그렇기 때문에 LIN통신으로 시스템 제어 및 모니터링 프로그램을 GUI(Graphic User Interface)로 제작한다면 시스템 상태의 디스플레이 및 모니터링이 수월해진다. 함수와 GUI로 제작되는 LabVIEW는 다른 텍스트 언어기반 개발 프로그램에 비해 설계 시간 단축 및 사후 관리도 쉽다는 장점이 있다. 본 논문에서는 LabVIEW로 제작한 IBS 모듈 기능 검사 장비개발을 통해 LIN 통신으로 송수신되는 데이터를 확인하고 모니터링, 그리고 설계가 용이하다는 것을 소개하고자 한다.

• Journal of the Korea Society for Simulation
• /
• v.4 no.1
• /
• pp.59-73
• /
• 1995

Local area networks(LANs) recently become so large that they exceed their architected limits and users on different LANs may need to talk each other. This trend has led to a growth in the practice of interconnecting many heterogeneous LANs. In this paper, we proposed a method to interconnect Ethernets and token rings, which are widely used today, through a fast FDDI network. We also developed a simulation tool to evaluate the performances of the interconnected networks. We used a simulation language SLAM II for modeling and OSF/MOTIF X-window for user interface. The developed tool can be used to make a decision which interconnecting method is suitable for a given environment before interconnecting many heterogeneous LANs.

• Journal of Communications and Networks
• /
• v.8 no.4
• /
• pp.369-377
• /
• 2006

Recently, the metropolitan area network (MAN) has attracted much attention in telecommunication research and has emerged as one of the most important research topics in the community. Several standards representing the first step for developing metropolitan networks have been published; IEEE 802.16 (WiMAX) has taken a relevant role in reaching the goal of realizing a full-service network all over a urban and suburban area. At the same time, the wireless local area networks (WLAN) have been widely used for in-home or short range communications, mainly basing on the IEEE 802.11 (WiFi) standard. A consequence is the increasing interest in interworking technology, that allows an interconnection between different standards by maintaining certain properties, mainly in terms of quality of service (QoS). One of the major issues is to design bridging devices capable of transparently interconnect different wireless technologies. In this paper, we propose two interconnection bridging solutions between WiMAX and WiFi links; the first is more based on the concept of maintaining a certain end-to-end QoS level independently from the wireless technologies used. The second method is more devoted to the reduction of the implementation complexity at the cost of no QoS assurance. The performance of the two methods are compared by resorting to computer simulations showing the advantages of each one technique.