• 한국공작기계학회논문집
• /
• 제13권4호
• /
• pp.73-78
• /
• 2004

The conventional SLT(Shear Lag Theory) which has been proven that it can not provide sufficiently accurate strengthening predictions in elastic regime when the fiber aspect ratio is small. This paper is an extented work to improve it by modifying the load transfer mechanism called NSLT(New Shear Lag Theory), which takes into account the stress transfer across the fiber ends and the SCF(Stress Concentration Factor) that exists in the matrix regions near the fiber ends. The key point of the model development is to determine the major controlling factor among the material and geometrical coefficients. It is found that the most affecting factor is the fiber/matrix elastic modulus ratio. It is also found that the proposed model gives a good result that has the capability to correctly predict the elastic properties such as interfacial shear stresses and local stress variations in the small fiber aspect ratio regime.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.51-58
• /
• 2013

This paper proposes the power conversion mechanism of a bailer-charge-transfer zero-current-switching (CT-ZCS) circuit. The operation modes are analyzed and researched using state trajectory equations. The topology of CT-ZCS based on soft-switching inverters offers some merits such as: tracking the input reference signal dynamically, bearing load shock and short circuit, multiplying inverter N+1 redundancy parallel, coordinating power balance for easy control, and soft-switching commutation for high efficiency and large capacity. These advantages are distinctive from conventional inverter topologies and are especially demanded in AC drives: new energy generation and grid, distributed generation systems, switching power amplifier, active power filter, and reactive power compensation and so on. Prototype is manufactured and experiment results show the feasibility and dynamic voltage-tracking characteristics of the topology.

• 한국지반공학회지:지반
• /
• 제12권6호
• /
• pp.21-36
• /
• 1996

흙과 Geogrid사이의 응력 전달은 마찰저항 및 수동저항으로 나눌 수 있는데 Geogrid의 횡방향 요소에 작용하는 수동저항은 그 메카니즘이 복잡하여 아직까지 거동이 명확하게 파악되지 못하고 있다. 이러한 수동저항의 메카니즘을 이해하기 위하여 돌기가 있는 보강재에 대한 직접 전단시험을 유한 요소 방법으로 해석하였다. 유한 요소해석으로 돌기의 간격에 따라 수동저항의 크기, 파괴형태, 응력 및 변형 분포 등을 분석하였으며 일 결과들을 실제 계측치와 비교 분석하여 Geogrid의 횡방향 요소에 작용하는 보강재의 수동저항의 거동을 파악하도록 하였다. 또한 흙의 종류에 따라 수동저항의 메카니즘을 파악하기 위해 점성토에 작용하는 수동저항의 거동을 예측하였다.

• Journal of Communications and Networks
• /
• 제7권3호
• /
• pp.337-352
• /
• 2005

In this paper, a fuzzy logic implementation of the random early detection (RED) mechanism [1] is presented. The main objective of the proposed fuzzy controller is to reduce the loss probability of the RED mechanism without any change in channel utilization. Based on previous studies, it is clear that the performance of RED algorithm is extremely related to the traffic load as well as to its parameters setting. Using fuzzy logic capabilities, we try to dynamically tune the loss probability of the RED gateway. To achieve this goal, a two-input-single-output fuzzy controller is used. To achieve a low packet loss probability, the proposed fuzzy controller is responsible to control the $max_{p}$ parameter of the RED gateway. The inputs of the proposed fuzzy controller are 1) the difference between average queue size and a target point, and 2) the difference between the estimated value of incoming data rate and the target link capacity. To evaluate the performance of the proposed fuzzy mechanism, several trials with file transfer protocol (FTP) and burst traffic were performed. In this study, the ns-2 simulator [2] has been used to generate the experimental data. All simulation results indicate that the proposed fuzzy mechanism out performs remarkably both the traditional RED and Adaptive RED (ARED) mechanisms [3]-[5].

• 한국지반공학회지:지반
• /
• 제13권5호
• /
• pp.75-88
• /
• 1997

본 연구에서는 항타말뚝과 비교한 현장타설말뚝의 극한지지력을 하중전이함수를 적용하여 예측하였으며 이를 토대로 항타말뚝과 비교한 현장타설말뚝의 지지력을 현장재하시험 결과와 비교, 분석하였다. 비교, 분석은 하중전이함수들 중 응력 연화를 고려한 방법, 쌍곡선 함수법 및 탄소성 방법을 대표하는 Vijayvergiya의 방법, Castelli의 방법 및 2중 직선법을 적용하여 지반 종류에 따라 현장타설말뚝의 하중-변위관계를 산정하였다. 본 연구 결과 동일한 지반에 설치된 항타말뚝과 현장타설말뚝의 극한지지력은 총 주면마찰력의 차이로 인하여 항타말뚝이 더 큰 것으로 나타났으며 이러한 차이는 점토질 지반에서 보다는 모래질 지반에서 더 크게 나타났다. 같은 지지력을 발현하기 위해 필요한 말뚝 두부에서의 변위량은 항타말뚝보다는 현장타설말뚝에서 더 크게 나타났으며 현장타설말뚝이 극한지지력을 발현하기 위해 필요한 변위량과 이와 같은 크기의 지지력을 발현하는데 필요한 항타말뚝의 변위량과의 차이는 모래질 지반에서 가장 크게 나타났다. 현장타설말뚝과 항타말뚝의 말뚝직경과 길이의 비(LID)의 변화에 따른 극한지지력의 차이는 점토질 지반의 경우 일정한 것으로 나타났으나 모래질 지반에서는 LID의 비가 증가할수록 극한지지력의 차이가 증가하는 것으로 나타났다.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.896-905
• /
• 2003

A linear motor has many advantages next to conventional feed mechanisms: high transitional speed and acceleration, high control performance, and good positioning accuracy at high speed. Through the omission of a power transfer element, the linear motor shows no wear and no backlash, has a long lifetime, and is easy to assemble. A disadvantage of the linear motor is low efficiency and resultant high-temperature rise in itself and neighboring structures during operation. This paper presents the thermal behavior of the linear motor as a feed mechanism in machine tools. To improve the thermal behavior, an insulation layer is used. By placing the insulation layer between the primary part and the machine table, both the temperature difference and the temperature fluctuation in the machine table due to a varying motor load are reduced.

• 한국정밀공학회지
• /
• 제14권3호
• /
• pp.35-40
• /
• 1997

The traction drive has advantages of having high efficiency and transmitting the power without blacklash. However, when high ratio of speed reduction is desired, excessively large size is required. In this study, a new type of traction drive is invented, designed and manufactured so that stable speed reduction mech- anisms are available by adopting a cross roller type drive. It has a simple structure, but produces high speed reduction ratio. Power loss is observed, and also, driving torque and torque transfer efficiency are calculated. Pre-loads are needed in order that the traction drive transfers power without slipping, and the spacer is enlarged due to the pre-loading. After all, the key point of pre-load mechanism is that the spacer's diameter becomes larger as pre-loads are applied.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.121-124
• /
• 2005

A novel process to fabricate carbon nanotube (CNT)/alumina nanocomposites, consisting of a molecular level mixing process and an in situ spark plasma sintering process, is proposed. The CNT/alumina nanocomposites fabricated by this proposed process show enhanced hardness due to a load transfer mechanism of the CNTs and increased fracture toughness arising from the bridging mechanism of CNTs during crack propagation

• Structural Engineering and Mechanics
• /
• 제56권6호
• /
• pp.983-1001
• /
• 2015

This study focuses on the load carrying capacity and the force transfer mechanism of multi-hole perfobond shear connectors in steel-concrete composite structure. The behavior of multi-hole perfobond shear connector is more complicated than single-hole connector cases. 2 groups push-out tests were conducted. Based on the test results, behavior of the connection was analyzed and the failure mechanism was identified. Simplified iterative method and analytic solution were proposed based on force equilibrium for analyzing multi-hole perfobond shear connector performance. Finally, the sensitivity of design parameters of multi-hole perfobond shear connector was investigated. The results of this research showed that shear force distribution curve of multi-hole perfobond shear connector is near catenary. Shear forces distribution were determined by stiffness ratio of steel to concrete member, stiffness ratio of shear connector to steel member, and number of row. Efficiency coefficient was proposed to should be taking into account in different limit state.

• Tribology and Lubricants
• /
• 제11권4호
• /
• pp.13-20
• /
• 1995

The present study was undertaken to investigate the purity variation of the alumina ceramics on the water lubrication mechanism. The annular surface of wear testing specimens of the alumina ceramics with different alumina purity against STB2 was rubbed in the distilled water under various sliding speed, contact pressure and sliding distance. The friction coefficient decreased lowered with formation of corrosion products due to the tribochemical reation as the sliding speed and contact load was increased. With increased sliding speed, the lower purity of 85 percent contribute largely to even degree of the friction surface, even it have about $\mu$ of 0.3 degree by the influence of a pore and impurities SiO$_{2}$. The friction surface of ceramics protacted by oxide was transfer from STB2.