• 대한기계학회논문집B
• /
• 제30권3호
• /
• pp.193-200
• /
• 2006

The purpose of this study is to compare the part-load performance of a SOFC/GT hybrid power system with three different kinds of load-following operation modes. The primary mode for the part load operation of a hybrid power system is the reduction of supplied fuel (e.g., fuel control mode) to the hybrid system. The other two options, i.e., variable speed and VIGV controls, are related to the reduction of supplied air simultaneously with the reduction of supplied fuel to the system. With the performance analysis of a SOFC/GT hybrid power system, it is concluded that the variable speed con佐ol mode Provides the best performance for the part-load operations. It is also found that the VIGV control mode, with its better performance behavior than the fuel control mode, can be used as an important option for the part-load operation especially in case that the variable speed control mode can not be adopted.

• 한국물환경학회지
• /
• 제37권6호
• /
• pp.469-482
• /
• 2021

The recent climate change and urbanization have seen an increase in runoff and pollutant loads, and consequently significant negative water pollution. The characteristics of the pollutant loads vary among the different flow regime depending on their source and transport mechanism, However, pollutant load reduction based on flow regime perspectives has not been investigated thoroughly. Therefore, it is necessary to analyze the effects of concentration on pollutant load characteristics and reductions from each flow regime to develop efficient pollution management. As non-point pollutants continuously increase due to the increase in impervious area, efficient management is necessary. Therefore, in this study, 1) the characteristics of pollutant sources were analyzed at the Dalcheon Basin, 2) reduction of nonpoint pollution, and 3) reduction efficiency for flow regimes were analyzed. By analyzing the characteristics of the Dalcheon Basin, a reduction efficiency scenario for each pollutant source was constructed. The efficiency analysis showed 0.06% to 5.62% for the living scenario, 0.09 to 24.62% for the livestock scenario, 0.17% to 12.81% for the industry scenario, 9.45% to 38.45% for the land scenario, and 9.8% to 39.2% for the composite scenario. Therefore, various pollution reduction scenarios, taking into account the characteristics of pollutants and flow regime characteristics, can contribute to the development of efficient measurements to improve water quality at various flow regime perspectives in the Dalcheon Basin.

• Journal of Electrical Engineering and Technology
• /
• 제1권1호
• /
• pp.85-91
• /
• 2006

Recently, the reduction of electromagnetic vibration and noise of a capacitor motor (CRM) has become a very important subject from the standpoint of environmental improvement. Therefore, the authors have studied the characteristics of the dominant electromagnetic vibration of the CRM under load condition. In this paper, the effects of slot combination and skewed slot on the dominant electromagnetic vibration of a CRM under load condition are discussed both theoretically and experimentally. As a result, the characteristics of the dominant electromagnetic vibration for the slot combination and the reduction effect of the skewed slot on the electromagnetic vibration are clarified for a 4-pole CRM.

• 전기학회논문지P
• /
• 제65권3호
• /
• pp.210-215
• /
• 2016

The transient characteristics of the Mg/Air fuel cell were ascribed to the load current, electrolyte concentrations, air electrode area and electrode distance. It was found that transient phenomena occurred in the load current, which is due to activate of the oxidation and reduction reaction process. The transient time increase with the load current increase. The transient characteristics were investigated with regard to internal resistance. The maximum power output analysis was employed in order to explain the delayed action under various experimental conditions. The internal resistances had a significant effect on the transient characteristics. The transient curves thus obtained were in almost agreement with internal resistance characteristics.

• 풍력에너지저널
• /
• 제13권3호
• /
• pp.43-52
• /
• 2022

Although wind turbines have obtained type certification according to international standards and are released to the market, they cannot be regarded as design evaluations that consider site characteristics. Therefore, it is necessary to study the site-specific load analysis method based on the meteorological data measured at the candidate site. In this study, site-specific load calculation was performed based on the meteorological data from the Jeju Haengwon mast. Analysis results were compared and analyzed with the results calculated by IEC design Class (IIA). For the fatigue loads at the blade root and tower base, the site-specific condition was lower than the IEC IIA, but in the case of the ultimate load, the site-specific condition showed higher results in some design load cases (DLCs). Selecting a wind turbine suitable for a site through load evaluation considering site conditions can prevent the reduction of operation and maintenance (O&M) costs and the power loss caused by downtime. Finally, it is expected to contribute to the project's levelized cost of energy (LCOE) reduction.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.180-186
• /
• 2009

To meet the NOx limit without a penalty of fuel consumption, urea SCR system is currently regarded as promising NOx reduction technology for diesel engines. SCR system has to achieve maximal NOx conversion in combination with minimal $NH_3$ slip. In this study, as a basic research to develop an algorithm for urea injection control, the characteristics of engine out NOx emission and behavior of NOx reduction during steady-state and transient conditions were investigated using 2L DI diesel engine. Test results show that on increasing the catalyst temperature the variations in the outlet NOx concentration are faster and maximal allowable $NH_3$ storage exponentially decreases. For change from a low to high engine load, it can be seen that a few seconds after load-step is required to reach full NOx conversion and the adsorbed amount of $NH_3$ at lower temperature desorb during the next temperature increase, causing $NH_3$ slip. Engine out NOx emission needs to be corrected because NOx emissions just after step load is lower than that of steay state condition.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2000년도 춘계 학술발표회 논문집
• /
• pp.153-157
• /
• 2000

• 전기학회논문지
• /
• 제63권12호
• /
• pp.1627-1636
• /
• 2014

In real-time electricity price environment, the energy management system can provide the significant advantage to the residential, commercial and industrial customers since it can reduce the electricity charge by controlling the load operation effectively in response to time-varying price. However, the earlier studies for load management mainly focus on the residential and commercial customers except for the industrial customers because most of load operations in industrial sector are intimately related with production schedule. So, it is possible that the inappropriate control of loads in industrial sector causes huge economic loss. In this paper, therefore, we propose load control algorithm for factory energy management system(F-EMS) to achieve not only minimizing the electricity charges but also maintaining production efficiency by considering characteristics of load operation and production schedule. Considering characteristics of load operation and production schedule, the proposed load control algorithm can reflect the various characteristics of specific industrial customer and control their loads within the range that the production efficiency is maintained. Simulation results show that the proposed load control algorithm for F-EMS leads to significant reduction in the electricity charges and peak power in industrial sector.

• 대한토목학회논문집
• /
• 제28권3D호
• /
• pp.399-405
• /
• 2008

포장궤도는 기존선의 유지보수 노력을 절감하기 위하여 개발되고 있다. 이 중 베이스플레이트 저탄성패드는 궤도 전체의 지지강성을 결정하는 구성품으로서 궤도의 응력-변위특성, 동적응답, 피로특성 등에 가장 큰 영향을 미친다. 따라서 저탄성패드의 적용은 궤도전체의 내구성과 안정성에 미치는 영향이 크다고 할 수 있다. 본 논문에서는 저탄성패드의 적용으로 인하여 획득되는 효과 중 노반에 전달되는 열차하중의 저감에 대한 연구를 수행하였다. 이를 위하여 패드스프링계수별 정적해석과 실물반복재하시험을 수행하고 그 결과를 비교 분석하여 저탄성패드의 하중 전달특성을 파악하였으며 전달하중 저감효과를 검토하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 제18회 학술대회 초록집
• /
• pp.57-62
• /
• 1993

To increase the fuel economy, a reduction of friction loss is important in engines. Experimental investigations have been required for reducing the friction loss of crankshaft bearings. Hydraulic cylinder, and servo control ler system which modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated. Experiment is performed. Friction torque, journal locus and circumferential temperature variations of crankshaft bearings were measured with appling load, revolution speed, and oil inlet temperature, etc.