• 한국대기환경학회지
• /
• 제26권5호
• /
• pp.499-506
• /
• 2010

Recently, a great deal of attention have been directed to the use of alternative fuels as a means to reduce vehicular emissions. As one of the promising alternative fuels, bio-diesel has advantages of a wide adaptability without retrofit of diesel engine. It is also effective enough to reduce CO, THC, $SO_x$, polycyclic aromatic hydrocarbons (PAHs) and PM. In this study, we investigated the emission characteristics of biofuels between different operating conditions, i.e., engine speed (1,400 rpm and 2,300 rpm), engine load (10% and 100%), bio-diesel blending (BD0, BD5 and BD20), and recirculation (EGR) rate of exhaust gas (0% and 20%). Relative performance of the system was evaluated mainly for the greenhouse gases ($CH_4$, $N_2O$ and $CO_2$). In addition, emission characteristics of ND-13 mode were also tested against both greenhouse gases and other airborne pollutants under emission regulation. The relative composition of bio-diesel has shown fairly clear effects on the emission quantities of CO, THC, and PM emission, although it was not on $NO_x$ and greenhouse gases. EGR rate has shown trade-off characteristics between $NO_x$ and PM.

• 유기물자원화
• /
• 제6권1호
• /
• pp.53-66
• /
• 1998

음식물쓰레기의 발생량과 조성점유율이 증대됨에 따라 음식물쓰레기의 효율적인 처리 및 처분이 쓰레기 관리행정의 성공여부를 좌우하므로 도시규모별, 발생원별 음식물쓰레기의 양과 조성 그리고 단위 가정 및 퇴비화 의무대상업소에서의 배출현황을 조사하여 이를 통한 수거체제를 고찰하였다. 대전시와 충청남도 5개 표본도시로부터 조사한 음식물쓰레기의 연평균 조성은 50%를 넘고 있으며 주택가, 아파트, 상가지역간 조성비의 차이는 거의 없다. 종이류가 약 25% 정도를 유지하고 있기 때문에 매립장에 유입되는 일반폐기물의 75% 이상이 퇴비화로 처리가 가능하다. 음식물쓰레기 발생원단위는 단위가정조사의 경우 200~250g/인 일이며 매립장에서 전체 발생 쓰레기를 기준으로 조사할 경우 380~400g/인 일이다. 이는 가정의 구성원이 가정에서보다 가정 밖에서 2배에 가까운 음식물쓰레기를 배출하고 있음을 시사해 주고 있다. 음식물쓰레기 감량화 의무대상업소인 연구소와 관공서의 음식물쓰레기 원단위는 각각 166g/인 일과 215g/인 일로 조사되었고 대중음식점의 경우 수준에 따라 발생원단위는 현저하다. 고급인 경우 670g/인 일, 중급은 190g/인 일 그리고 대중음식점은 평균 60g/인 일이다. 1급 호텔의 경우 400g/인 일이며 집단급식소인 대학교 학생회관의 경우 170g/인 일로 조사되었다. 가정용 퇴비화 용기내에서 자연감량율은 1일 3~4%의 수준을 나타내고 있다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.88-94
• /
• 1999

Recently, PTFE-polyimide composites are being used self-lubricating parts for industrial field. Thus, this study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polyimide composites. The friction and wear test was carried out for the different composition ratio under the atmosphere room temperature and constant load of 7.69N and their friction and wear properties were compared with each other at various sliding speed. Notable results are summarized as follows. PTFE 100% showed that friction coefficient was almost same values at 0.94 and 1.88m/s but the value was decreased at 2.83m/s because the friction temperature is higher than low speed. PTFE 80%-PI 20% showed the lowest mean friction coefficient at 2.83m/s. PTFE 20%-PI 80% showed the highest friction coefficient at 0.94m/s and the value was decreased at high speed but the value is higher than other materials except PTFE 100 %. PI 100% showed the highest friction coefficient at 0.94 and 1.88m/s because adhesive wear mainly occurred that speed. PTFE 100% showed highest specific wear rate on the whole. Specific wear rate of PTFE 80%-PI 20% was almost the same value with PTFE 20%-PI 80%. PI 100% showed the lowest value at high sliding speed because the friction surface was thicken and carbonated by high friction temperature.

• 대한치과교정학회지
• /
• 제25권2호
• /
• pp.187-200
• /
• 1995

국산 Ni-Ti합금 교정용 선재(ORTHOLLOY)의 특성을 평가하기 위하여 성분, 인장특성, 굽힘특성, 열처리성, 내식성, 이온용출 등에 대해 조사하고 외국산 Ni-Ti합금 선재(SENTALLOY)의 특성과 비교 분석한 결과는 다음과 같았다. ORTHOLLOY는 초탄성 효과를 나타내는 범위내에서의 Ni과Ti 함량을 포함하고 있었다. 인장실험에서 ORTHOLLOY는 연신율 $2\%$에서 $8\%$정도 범위내에서 하중의 변화가 거의 없는 초탄성 효과를 나타내었다. 3점 굴곡실험에서 ORTHOLLOY는 SENTALLOY 보다 같은 변위량에서 높은 하중값을 나타내었고, 초탄성을 나타내는 변위영역에서의 하중 범위는 ORTHOLLOY의 경우 0.014" 에서 80-100g, 0.016"에서 140-180g, 0.018" 에서 150-200g의 값을 나타내었다. $400^{\circ}C,\;500^{\circ}C$의 열처리에 의해 초탄성을 나타내는 하중범 위가 낮아졌고, 각 열처리 온도에서는 시간이 증가함에 따라 초탄성을 나타내는 하중값의 범위가 낮아졌으며 $600^{\circ}C$에서는 10분간의 열처리로 초탄성 효과가 소실되었다. 용출되어 나온 Ni 이온의 양은 SENTALLOY의 0.01ppm미만의 극소량에 비해 ORTHOLLOY에서는 0.3ppm 전후로 높게 나타났다. 침적 실험후 주사전자현미경 관찰을 통한 표면조직 소견은 SENTALLOY에서는 침적 전후 및 침적 시간의 경과에 관계없이 전체적으로 비교적 균일한 양상을 보였으나 ORTHOLLOY에서는 pitting corrosion양상을 보였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.379-380
• /
• 2002

Steam generators (S/G) of pressurized water reactors are large heat exchangers that use the heat from the primary reactor coolant to make steam in the secondary side for driving turbine generators. Reciprocating sliding wear experiments have been performed to examine the wear properties of Incoloy 800 and Inconel 690 steam generator tubes in high temperature water. In present study, the test rig was designed to examine the reciprocating and rolling wear properties in high temperature (room temperature - $300^{\circ}C$) water. The test was performed at constant applied load and sliding distance to investigate the effect of test temperature on wear properties of steam generator tube materials. To investigate the wear mechanism of material, the worn surfaces were observed using scanning electron microscopy. At $290^{\circ}C$, wear rate of Inconel 690 was higher than that of Incoloy 800. It was assumed to be resulted from the oxide layer property difference due to the a\loy composition difference. Between 25 and $150^{\circ}C$ the wear loss increased with increasing temperature. Beyond $150^{\circ}C$, the wear loss decreased with increasing temperature. The wear loss change with temperature were due to the formation of wear protective oxide layer. From the worn surface observation, texture patterns and wear particle layers were found. As test temperature increased, the proportion of particle layer increased.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.638-641
• /
• 2008

Computational investigation was conducted to study the effects of the shape parameter of shroud on the performance of the outdoor unit of an air-conditioners. For this study the Design of Experiment(4-factor 3-level) was created and the an automatic program was composed using VBA to reduce the load of pre-process for CFD. The estimated mathematical equation was produced from this analysis and it was found that the gap between fan and shroud affects more heavily than the other parameters. As a result, the composition of the best parameters was verified that its flow rate was increased by 10 percents and sound pressure level was reduced by 1.2 dBA compare with the worst. And finally, a kind of Propeller fan with blades which were attached to the shroud, so-called 'ProBeller Fan' was introduced in this study.

• 대한치과보철학회지
• /
• 제19권1호
• /
• pp.17-27
• /
• 1981

This study was conducted to determine the chemical composition and the mechanical properties of four commercially available low gold-based crown and bridge alloy produced in Korea. Four dental casting gold-silver-palladium alloys, i.e., A, B, C and D (code of alloys) were selected for the evaluation of chemical composition, ultimate tensile strength, elongation. values and Vickers hardness. The chemical composition of test specimens was analyzed by both emission spectrography and wet gravitation method with a 1.5gm of low gold ingot. The tensile properties and Vickers hardness was determined with cast specimens treated in following three conditions; as-cast, softening heat treatment and hardening heat treatment. The tensile testing bars were cast in accordance with the model designed by Gettleman and Harrison (1969) which was modified from the A. D. A. Specification No. 14 for dental chromium-cobalt casting alloy. Nine tensile test specimens were made from a split silicone mold for each of the test alloys to the size of 2.5mm in diameter and a gauge length of 10mm. All four alloys were handled in accordance with conventional methods used in Type III gold alloys. Ultimate tensile strength and elongation were measured on an Instron Universal Tensile Testing Machine (Model 1125, Japan) operated at a crosshead rate of 0.1cm/min. Elongation values were measured using Digital Measuring Microscope (MS-152, FUSOH, Japan). Vickers hardness was determined with a Vickers Hardness Tester (Model VKH-l, Japan) at a 1.0kg load on a mounted tensile test specimen. The following results were obtained from this study; 1. All tested alloys were composed of Au, Ag, Pd, Cu, Zn and Fe in common. The composition rate of gold for all four alloys was found in the range of $42{\sim}47$ weight % as shown below. Alloy A; Au 45%, Ag 40.2%, Pd 5.76%, others 9.04%. Alloy B; Au 47.1%, Ag 29.03%, Pd 6.98%, others 16.92%. Alloy C; Au 45%, .Ag 26.9%, Pd 6.83%, others 21.07%. Alloy D; Au 41.8%, Ag 34.4%, Pd 6.95%, others 16.85%. 3. The ultimate tensile strength of the four alloys was in the range of $31{\sim}82kg/mm^2$. The test results were shown in the below order from the highest value; As-cast condition; D, B, C, A. Softening heat treament; B, C, D, A. Hardening heat treatment; D, B, C, A. 4. The test :results of the elongation rate for each alloy were in the range of $0.5{\sim}18%$. The test results were shown in the below order from the highest value; As-cast condition; A, D, B, C. Softening heat treatment; A, C, D, B. Hardening heat treatment; C, D, B, A. 5. Vickers hardness for each of the four alloys was in the range of $120{\sim}230$. The test results were shown in the below order from the highest value; As-cast condition; C, B, D, A Softening heat treatment; D, B, C, A. Hardening heat treatment; D, A, C, B. 6. There were no differences in the physical properties between as-cast condition and softening heat treatment.

• 한국물환경학회지
• /
• 제28권6호
• /
• pp.933-942
• /
• 2012

The purpose of this study is to evaluate the degree of waterbody impairment according to the flow conditions and present to the appropriate water quality improvement alternatives using observed water quality and flow for Total Maximum Daily Load (TMDL) implementation at 39 unit watersheds the nakdong river basin. Observed water quality data for 7 years are divided into five cumulative flow frequency group and comparing the each observed water quality data and TMDL Target water quality (TWQ) the last evaluate the water quality is impaired group. We found that the cumulative flow frequency group-specific the average excess rate of V group was the highest (32.86%), followed by the IV group (26.04%), group III (23.36%), II group (22.67%), I group (20.70%), the degree of impaired waterbody tended to be inversely proportional to the flow rate. Resulted from cumulative flow frequency group of impaired water quality assessment, 13 unit watersheds are impaired from a group IV and group V affected by point sources. Therefore, improvement of sewage discharge and the initial composition of the riparian buffer zone are needed. Nakbon F, Namkang D and Namkang E within 13 unit watersheds are impaired from group II and III affected by non-point sources. Therefore, application of Best Management Practices (BMPs) is needed for these watersheds. Evaluation of impaired waterbody using Cumulative flow frequency group is able to determine the extent of the judgment to TWQ exceeded by the flow conditions and helps proper setting Standard flow and planning pollutant reduction for TMDL.

• 지질공학
• /
• 제31권4호
• /
• pp.541-547
• /
• 2021

비탈면의 유실, 붕락사고 등 비탈면에 대한 안정성을 파악하기 위해서 지층의 구성상태, 역학적 특성 등의 지반정보 파악이 필요하다. 이러한 지반정보를 파악하기 위해서 일반적으로 표준관입시험(SPT) 및 콘 관입시험 등이 널리 이용되고 있다. 대부분이 급경사로 이루어지고 진입로가 없는 비탈면에 대한 접근성 문제로 표준관입시험이 널리 활용되지 못하고 있다. 이러한 단점을 보완할 수 있는 있는 휴대용 장비인 Drop Cone Penetrometer(DCP)를 이용한 조사도 여러 가지 문제로 제한적으로 사용되고 있다. 따라서 본 연구에서는 비탈면 현장접근이 용이한 휴대용 시추기와 동적콘관입시험 모듈을 개발하고, 개발된 동적콘관입시험기를 이용한 결과와 동일 현장에서 수행한 표준관입시험값과 상관성을 분석하였다. 에너지전단율로 보정된 동적콘관입시험과 표준관입시험간의 상관식은 N_d' = 3.13 N'으로 나타났다.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.