국내의 경우 이 등(1994)의 연구를 시작으로 국지 현장별로 타입말뚝의 지지력 증가효과에 대한 사례연구들이 있었다. 그러나 충분한 시험자료를 바탕으로 한 지지력 증가효과에 대한 전반적인 검토는 아직 미흡한 실정이고, 또한 지지력 증가효과에 지반조건 및 말뚝의 형상이 미치는 영향에 대해서는 아직 보고 된 바 없다. 타입말뚝의 지지력 증가효과를 실무적으로 이용하기 위해서는 현장에서 실구조물에 적용된 말뚝에 대한 시험자료의 분석을 실시하는 것이 필요하다. 본 연구에서는 말뚝기초의 설계 및 향후 사질토에서의 지지력 증가효과 등의 연구를 위한 기본 자료로 활용하기 위해 실구조물에 적용되는 다양한 시험말뚝의 시공과 동재하시험 자료 분석을 통해 지지력 증가효과에 대한 현상을 알아보았다. 말뚝의 동재하시험의 분석 결과, 말뚝지지력의 증가는 토질별로도 영향을 받지만 조성이력에도 영향을 받는 것으로 분석되었으며, 특히 사질토에도 상당한 지지력 증가효과가 나타났다. 이러한 말뚝의 지지력의 증가는 주로 주면부에서 발생하였으며, 선단형상에 따른 지지력 증가효과는 점성토에서는 폐단말뚝이 크고, 사질토에서는 개단말뚝이 큰 것으로 나타났다.
The purpose of this study is to investigate the influence of train-induced end rotation of simple supported track girder on the performance of a direct fixation track system (DFTS) in Yeongjong grand bridge. In this study, the influences of deflection of a DFTS and track girder on dynamic rail-track girder interaction forces for the track girder ends currently employed in airport express lines were assessed by performing field tests using actual vehicles running along the service lines. Therefore, the dynamic displacement of rail and track girder and the fastener stress on the center and ends sections of DFTS were measured for two different trains (AREX and KTX) running in Yeongjong grand bridge. A three-dimensional finite element analysis (FEA) model using the time-history function based on the design wheel load was used to predict the train-induced track and track girder displacement, and the FEA and field test results were compared. The analytical results reproduced the experimental results well within about 3-7% difference in the values. Therefore, the FEA model of DFTS on track girder is considered to provide sufficiently reliable FEA results in the investigation of the behavior of DFTS. Using the analytical and experimental results, the influence of train-induced end rotation of simple supported track girder on the interaction behavior of rail and track girder installed on a simple supported track girder ends, i.e., upward displacement of rail-track girder and the fastener stress, was investigated. It was found that the train-induced end rotation effect of track girder was not significantly affected by the upward displacement of rails and the fastener stresses of track girder ends. Further, the interaction behavior of rail and track girder were similar to or less than that of the general railway bridge deck ends, nevertheless the vertical displacement of track was higher than that of conventional DFTS on the general railway bridge. From the results, the dynamic responses of the DFTS on track girder ends were not significantly affected by the safety and stability of DFTS ends.
Steel-concrete composite structures have been extensively used in building, bridges, and other civil engineering infrastructure. Shear stud connectors between steel and concrete are essential in composite members to guarantee the effectiveness of their behavior in terms of strength and deformability. This study focuses on investigating the shear stiffness of headed studs embedded in several types of concrete with wide range of compressive strength, and their effects on the elastic behavior of steel-concrete composite girders were evaluated. Firstly, totally 206 monotonic push-out tests from the literature were reviewed to investigate the shear stiffness of headed studs embedded in various types of concrete (NC, HPC, UHPC etc.). Shear stiffness of studs is defined as the secant stiffness of the load-slip curve at 0.5Vu, and a formulation for predicting defined shear stiffness in elastic state was proposed, indicating that the stud diameter and the elastic modulus of steel and concrete are the main factors. And the shear stiffness predicted by the new formula agree well with test results for studs with a diameter ranging from 10 to 30 mm in the concrete with compressive strength ranging from 22.0 to 200.0MPa. Then, the effects of shear stiffness on the elastic behaviors of composite girders with different sizes and under different loading conditions were analyzed, the equations for calculating the stress and deformation of simply supported composite girders considering the influence of connection's shear stiffness were derived under different loading conditions using classical linear partial-interaction theory. As the increasing of shear stiffness, the stress and deflection at the most unfavorable section under partial connected condition tend to be those under full connected condition, but the approaching speed decreases gradually. Finally, the connector's shear stiffness was recommended for fully connection in composite girders with different dimensions under different loading conditions. The findings from present study may provide a reference for the prediction of shear stiffness for headed studs and the elastic design of steel-concrete composite girder.
천연가스를 연료로 사용하는 복합화력발전소는 석탄화력 대비 기동 및 정지가 용이하고 오염물질의 배출에 대한 부하가 적어 국내 발전설비 중 차지하는 비중이 꾸준히 상승하고 있다. 그러나 복합화력발전소는 가스터빈의 기동초기 및 저부하 운전 영역에서 황연현상을 일으키는 이산화질소(NO2)의 농도가 높은 특성을 가지고 있어 민원의 원인이 되며, 이의 제어 기술로서 황연제거설비가 2000년대 중반에 개발되어 운영되어 지고 있었다. 하지만 이 기술은 가스터빈 냉간기동 조건에서 기동초기 약 10~20분 동안은 기화시스템의 예열이 충분하게 이루어 지지 않아 황연현상을 제어할 수가 없는 실정이었다. 이에 본 연구에서는 환원제를 기화기를 사용하지 않고 액상의 상태로 가스터빈 Exhaust Duct에 직접 분사하여 황연현상을 제어하는 기술의 도출을 위해 CFD 해석 및 실증시험을 수행하였다. 가스터빈 Exhaust Duct에 위치에 있는 Diffuser에 의해 Duct의 외곽으로 형성된 배기가스에 액상의 환원제를 직분사하는 방안으로 배기가스 조건에 따라 5가지 Case로 분류하여 CFD를 수행하였으며, 그 결과 5가지 Case 모두에서 RMS가 15%이하로 양호한 혼합도를 보였다. 이를 바탕으로 실증설비를 설치 및 시험을 실시한 결과, 기존 기상주입방식에서 제어할 수 없었던 기동 초기 약 10~20분 구간의 황연현상도 완벽하게 제어할 수 있었다.
Statement of problem : Although zirconium oxide ceramics are more and more commonly used in restorative dentistry, for many clinical applications only limited data can be found in the literature. However it is quite clear that hydrofluoric acid etching is impossible with zirconia ceramics. Therefore, other bonding techniques are required in order to lute these materials adhesively. Purpose : The purpose or this study was to evaluate the effects of surface treatments on shear bond strengths between two resin cements and a zirconia ceramic. Materials and methods : Experimental industrially manufactured yttrium-oxide-partially-stabilized zirconia ceramic discs (Adens, Korea) were used for this study. The ceramic specimens divided into five experimental groups and a control group (as received). Five surface treatments were studied 1) sandblasting with 110$\mu$m $Al_2O_3$ at 3 bars pressure 13 seconds at a distance of 10 mm, 2) flame-treated with the Silano-Pen for 5 $s/cm^3$, 3) grinding with a diamond bur. 4) sandblasting + Silano-Pen treatment, 5) diamond bur preparation + Silano-Pen treatment. Acrylic plastic tube (5 mm in height and 3 mm in diameter) were filled with composite to fabricate composite cylinders The composite cylinders were bonded to the ceramic specimens with either Superbond C&B or Panavia F resin luting agents. All cemented specimens were tested under shear loading until fracture on universal testing machine at a crosshead speed 1mm/min; the maximum load at fracture was recorded. Sheat bond strength data were analyzed with oneway analysis of variance and Tukey HSD tests (P<.05). Treated ceramic surfaces and fracture surfaces after shear testing were examined morphologically using scanning electron microscope. Results: Ceramic surface treatment with Silano-Pen after sandblasting improved the bond strength of Superbond C&B resin cement. Supevbond C& B resin cement at Silano-Pen aiker sandblasting($27.4{\pm}3.8MPa$) showed statistically higher shear bond strength than the others. Conclusion: Within the limitation of this study, Superbond C& &B resin cement are suitable for cementation of zirconia ceramics and flame-treated with the Silano-Pen after sandblasting is required to enhance the bond strength.
본 연구에서는 방전가공(electric disharge machining, EDM) 또는 공기연마 분사기(air-abrasive jet machine, AJM) 가공에 의하여 인장 시험편 또는 외팔보 시험 편에 구멍깊이를 증가시켜 가면서 구멍을 뚫었다. 여기에서 방저가공(EDM)을 채택한 것은 구멍깊이를 직접 계측하는 것이 가능하여 구멍깊이 측정 오차에 기인하는 잔류응 력 측정오차를 최소화 할 수 있기 때문이며, 공기연마 분사기를 채택한 것은 구멍을 뚫는 동안 가공응력을 유발시키지 않기 때문이었다. 위 인장 시험편 또는 외팔보 시 험편을 이용하여 균일한 응력장과 두께 방향으로 변하는 선형적 구배응력장을 구현하 고, 이 때 각각 구멍깊이가 다른 원통형 막힘 구멍으로 부터 이완되는 스트레인을 계 측하였다. Schajer가 제안한 멱급수법과 최소장승법을 적용하여 균일응력장 또는 구 배 응력장에서 측정되는 스트레인을 잔류응력으로 환산하였으며, 환산된 잔류응력과 실제로 작용하는 응력을 비교하므로서 이론적으로 제시된 멱급수법과 최소자승법의 타 당성을 실험적으로 검토하는데 본 연구의 목적이 있다. 이 때 얕은 구멍깊이 (0.3∼ 1.2mm)에서 측정되는 스트레인을 이용하여 Schajer의 제안에 따라 잔류응력을 산정하 므로서, 잔류응력 계측 대상 구조물을 가급적 덜파괴시키며 잔류응력을 측정할 수 있 는지 여부를 실험적으로 검토하였다.
해수에 노출된 콘크리트 구조물은 시간의 경과에 따라 철근부식이 야기될 수 있으며, 이는 구조적인 성능저하로 진전된다. 1단계 연구에서 도출된 해수전착시스템의 개발을 통하여 2단계 연구에서는 해수전착 코팅된 철근 및 코팅철근을 사용한 RC 콘크리트 부재의 구조적, 내구적 성능이 평가되었다. 내구적 성능평가에서는 반전위 측정이 수행되었는데, 코팅된 철근은 일반철근의 35%수준의 부식속도를 가지고 있었으므로 높은 내부식성을 확보하고 있었다. 구조실험에서는 직접인장시험, 부착력시험, RC 부재를 이용한 휨 및 전단시험이 수행되었다. 인장강도 시험에서는 3.2%, 부착성능에서는 8.8%의 강도 증가가 코팅된 철근에서 평가되었다. RC보에 대한 실험에서는 최대하중 및 파괴형태는 두가지 경우에서 거의 동일하게 평가되었다. 해수전착된 시편은 철근주위에 콘크리트와 비슷한 화합물(수산화마그네슘, 탄산칼슘)이 형성되므로 부착력 및 강도를 일부 증가시키는 것으로 평가되었다. 해수전착철근은 피로, 내충격성, 장기침지실험 등을 통하여 성능이 입증되면 더욱 활발하게 사용될 것으로 사료된다.
비보강 조적조 건축물은 재료의 특성상 지진과 같은 횡력에 취약하지만, 국내에는 여전히 많은 조적조 건물이 존재한다. 특히 현재 남아있는 조적조 건축물의 대부분이 20년 이상 노후화됨에 따라 재해감소를 위한 경제성 있는 보강법의 개발이 요구된다. 본 논문에서는 이러한 노후 된 조적조 건축물의 보강법의 하나로 접착형 보강재를 활용한 조적벽체의 외부 보강법을 제시하였으며, 보강효과 검증을 위해 총 6개의 실험체를 형상비(L/H=1.0, 1.3, 2.0)를 변수로 제작하여 정적가력실험을 실시하였다. 실험결과, 보강전 후 조적벽체는 강체회전 및 미끄러짐에 의해 파괴가 발생하였고, 접착형 보강재 부착후 벽체의 최대내력, 최대변위, 소산에너지량은 증가하여 우수한 보강효과를 확인하였다. 또한 기존 유리섬유를 활용한 증가된 전단강도식에 착안하여 비보강 조적벽체에 대한 접착형 보강재의 설계안을 도출하여 적용을 위한 기초자료를 제공하였다.
히트블랑켓을 이용한 통상의 복합재 패치 수리의 경우, 진공백만을 이용하여 접착제에 압력을 가하게 된다. 그러나 본 연구에서는 진공백 위에 다시 공기압을 추가로 가할 수 있는 가압장치를 개발하였다. 개발된 가압장치의 성능을 검증하기 위해 탄소섬유 복합재 적층판을 스카프 패치로 수리하고 인장시험을 수행하여, 결함이 없는 온전한 구조물과의 강도를 비교하였다. 또한 비교를 위해 오토클레이브를 사용하여 패치를 접착한 동일한 형상의 시편에 대한 인장시험도 같이 수행하였다. 시험 결과 외부압력 없이 히트블랑켓과 진공만으로 수리한 시편, 개발된 가압장치로 1 기압을 추가로 가하여 수리한 시편, 그리고 오토클레이브에서 동일한 외부압력을 가하면서 수리한 시편의 인장강도 회복율은 각각 74.9, 81.0, 78.2%로 나타났다. 수분을 포화시킨 시편에 대한 인장강도 시험과 상온건조 인장 피로시험의 결과에서도, 개발된 가압장치를 이용해 1 기압 외부압력으로 제작한 시편은 오토클레이브로 제작한 시편과 동일한 수준 이상의 강도를 보이는 것을 확인하였다.
FRP-콘크리트 합성 바닥판은 압축에 강한 콘크리트를 상부에 위치시키고 인장에 강한 FRP를 하부에 위치시켜, FRP와 콘크리트가 갖는 장점을 극대화시킴으로서 내구성, 안전성 등을 두루 향상시킨 새로운 개념의 구조이다. 그러나 서로 다른 재질의 두 재료를 합성시키기 위한 방안으로서 연구 초기에 적용된 규사코팅 공법 외에 수직부착력을 향상시킬 수 있는 기계적 합성 방안을 고안하였다. 이렇게 고안한 합성 방안이 적용된 실제 사이즈의 바닥판 실험체를 제작하여 정적 및 피로반복실험을 수행하였다. 정적실험 결과 이 연구에서 제안한 합성 방안이 적용된 바닥판이 처짐 및 균열 등에 대해서 설계기준을 충분히 만족시켜 매우 우수한 성능을 나타내고 있었으며, 피로실험 결과 파괴하중의 50%로 200만회 가력한 후에도 처짐 및 균열 등에 대해 설계기준을 만족하고 있어 충분한 피로내구성을 확보하고 있는 것으로 나타났다. 이에 이 연구에서 제시한 규사코팅과 기계적 합성 방안을 동시에 적용한 합성 방안은 FRP-콘크리트 합성 바닥판에 대해 충분한 적용성을 갖고 있으며, FRP-콘크리트 합성 바닥판 설계시 제시한 설계조건들이 적절하게 이용될 수 있음을 확인하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.