• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1530-1535
• /
• 2003

The automatic load transfer switch (ALTS) typically automatically transfers electrical loads from a normal electrical power source to an emergency electrical power source upon reduction or loss of normal power source voltage. It can also automatically re-transfer the load to the normal power source when the normal voltage has been restored within acceptable limits. The transfer operation of ALTS is accomplished by a spring-driven linkage mechanism. In this paper we build a dynamic model of driving mechanism for ALTS using ADAMS and checked the characteristics of the transfer operation. Finally we performed a detailed design of the driving mechanism through results of analysis and confirmed it to satisfy design requirements.

• 한국지반공학회논문집
• /
• 제27권1호
• /
• pp.5-16
• /
• 2011

본 연구에서는 3차원 유한요소해석을 이용하여 석회공동형성 암반에 시공된 말뚝기초의 하중지지 메카니즘 변화를 분석하였다. 이를 위하여 공동의 기하학적 조건을 변화시키며 말뚝기초의 극한지지력, 지반의 항복형태, 말뚝과 공동 주위의 응력분포 및 말뚝기초의 침하와 공동의 변형 등 해석결과를 고찰하여 말뚝기초의 역학적 거동을 검토하였다. 본 연구결과, 말뚝의 하중지지 메카니즘, 지반의 파괴형태 및 말뚝기초의 극한지지력 감소율은 공동의 기하조건에 의해 결정되며 이러한 경향을 토대로 공동의 특정조건에 대한 말뚝의 극한지지력 감소율 그래프를 제시하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권3호
• /
• pp.8-15
• /
• 2019

Wheelchair users experience difficulty when using transportation. This is because wheelchair users must use transportation means together with wheelchairs. Therefore, in this paper, we developed a wheelchair storage system for passenger's car trunk. The mechanism is designed to allow a wheelchair and the device to be housed simultaneously in the narrow space of the trunk of the sedan passenger car. Additionally, this wheelchair storage system has implemented an initial load reduction mechanism that can mechanically reduce the initial load. This wheelchair storage system verified the system's operability through the production of the prototype. This system was actually installed in the trunk of the sedan passenger's car to verify the storage process. The operation and storage process of the wheelchair storage system was been perfectly verified. This wheelchair storage system will help a lot of self-driver or an assistant (female or elderly) who use wheelchairs.

• Agricultural and Biosystems Engineering
• /
• 제7권1호
• /
• pp.13-17
• /
• 2006

The planocentric gear, known as wobble mechanism, has been used for speed reducing mechanism as an ingenious mechanism. The modem application can be found in the backrest adjusting mechanism of a vehicle reclinable seat, fluid pumps and aircraft hoist and winches. Higher speed reduction ratios, high load capacity, lower weight, and compactness are the main advantages of this gear. This paper presents velocity and static force analysis to investigate the friction lock of the planocentric gear. The rectilinear tooth profile is used to maximize the speed reduction ratio. The equivalent linkage system is used for the analysis of instantaneous motion. As the results, the transmission efficiency of the planocentric gear is found and the friction lock of the system is determined for the friction coefficients of journals. A numerical example that illustrates the developed analysis is presented.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2157-2165
• /
• 2017

This study deals with the design of the mechanism in which demand response (DR) resources are traded in the power generation market. In general, a DR aggregator (DRA), which extends DR resources and provides technical support, is central to this mechanism. In this study, power users, called DR customer (DRC), participate in load reduction and are also modeled to participate directly in DR-related bidding. The DRA provides incentives to the DRC, indirectly impacting the market, and the DRC use the bid parameters strategically. We present the conditions for finding Nash Equilibrium (NE) in game problems of various participants including market operators, and analyze the characteristics of DRA and DRC related models. It also analyzes the impact of the participants on the market according to various types of competition and coalitions between DRA and DRC.

• 한국연소학회지
• /
• 제16권2호
• /
• pp.16-22
• /
• 2011

It is a challenging task to apply large detailed chemical mechanisms of fuel oxidation in simulation of complex combustion phenomena. There exist a few systematic methodologies to reduce detailed chemical mechanisms to smaller sizes involving less computational load. This research work concerns generation of a skeletal chemical mechanism by a directed relation graph with specified accuracy requirement. Two sequential stages for mechanism reduction are followed in a perfectly stirred reactor(PSR) for high temperature chemistry and to consider the autoignition delay time for low and high temperature chemistry. Reduction was performed for the detailed chemical mechanism of n-heptane consisting of 561 species and 2539 elementary reaction steps. Validation results show acceptable agreement for the autoignition delay time and the PSR calculation in wide parametric ranges of pressure, temperature and equivalence ratio.

• Steel and Composite Structures
• /
• 제45권1호
• /
• pp.51-66
• /
• 2022

This paper presents the axial compression behavior of partially encased composite (PEC) columns using H-shaped structural steel. In the experimental program, a total of eight PEC columns with H-shaped steel sections of different flange and web slenderness ratios were tested to investigate the interactive mechanism between steel and concrete. The test results showed that the PEC columns could sustain the load well beyond the peak load provided that the flange slenderness ratio was not greater than five. In addition, the previous analytical model was extended to predict the axial load-strain relationships of the PEC columns with H-shaped steel sections. A good agreement between the predicted load-strain relationships and test data was observed. Using the analytical model, the effects of compressive strength of concrete (21 to 69 MPa), yield strength of steel (245 to 525 MPa), slenderness ratio of flange (4 to 10), and slenderness ratio of web (10 to 25) on the interactive mechanism (K_h = confinement factor for highly confined concrete and K_w = reduction factor for steel web) and ductility index (DI = ratio between strain at peak load and strain at proportional load) were assessed. The numerical results showed that the slenderness of steel flange and yield strength of steel significantly influenced the compression behavior of the PEC columns.

• 한국정밀공학회지
• /
• 제14권3호
• /
• pp.35-40
• /
• 1997

The traction drive has advantages of having high efficiency and transmitting the power without blacklash. However, when high ratio of speed reduction is desired, excessively large size is required. In this study, a new type of traction drive is invented, designed and manufactured so that stable speed reduction mech- anisms are available by adopting a cross roller type drive. It has a simple structure, but produces high speed reduction ratio. Power loss is observed, and also, driving torque and torque transfer efficiency are calculated. Pre-loads are needed in order that the traction drive transfers power without slipping, and the spacer is enlarged due to the pre-loading. After all, the key point of pre-load mechanism is that the spacer's diameter becomes larger as pre-loads are applied.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권10호
• /
• pp.4988-5012
• /
• 2019

As a subset of the Internet of Things, the Internet of Energy (IoE) is expected to tackle the problems faced by the current smart grid framework. Notably, the conventional day-ahead power scheduling of the smart grid should be redesigned in the IoE architecture to take into consideration the intermittence of scattered renewable generations, large amounts of power consumption data, and the uncertainty of the arrival time of electric vehicles (EVs). Accordingly, a day-ahead power scheduling system for the future IoE is proposed in this research to maximize the usage of distributed renewables and reduce carbon emission caused by the traditional power generation. Meanwhile, flexible charging mechanism of EVs is employed to provide preferred charging options for moving EVs and flatten the load profile simultaneously. The simulation results revealed that the proposed power scheduling mechanism not only achieves emission reduction and balances power load and supply effectively, but also fits each individual EV user's preference.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.218-226
• /
• 2002

This study was carried out to develop continuously variable-speed transmission(CVT) fur an agricultural tractor. The full-toroidal variator mechanism with flour discs and six rollers was utilized as a device fur changing speed ratio continuously. In system layout design, the sizes of the roller cylinders and the end-load cylinder, which were critical factors for controlling the variator, were designed. The planetary gear unit and six pairs of the gear assemblies were designed to establish the maximum speed of the vehicle at 30 ㎞/hr. In addition, the hydraulic clutch, the silent chain, the hydraulic manifold and the electronic controller were designed. Based on the design, a prototype CVT was developed and tested. Test results show that the CVT developed in this study could successfully provide variable speed of the tractor.