• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.489-498
• /
• 1998

Among the heat/mass exchange units composing an absorption system, the absorber, where the refrigerant vapor is absorbed into the liquid solution is the one least understood. In the present study, the effects of non-absorbable gas on the absorption process of aqueous lithium bromide solution falling film inside a vertical tube were experimentally investigated. In the range of film Reynolds number of 30 ~ 195, heat and mass transfer characteristics were investigated as a function of non-absorbable gas volumetric concentration, 0.2 ~ 20%. An increase of non-absorbable gas volumetric concentration degraded the mass transfer rate dramatically in the absorption process. The reduction of mass transfer rate was significant for the addition of small amount of non-absorbable gas to the pure vapor. At film Reynolds number of 130, an increase of non-absorbable gas concentration from 0.2 to 6.0% resulted in the decrease of mass transfer rate by 36% and 20% of non-absorbable gas by 59%. However the decrease of film Nusselt number with the increase of volumetric concentration of non absorbable gas was relatively smaller than the decrease of Sherwood number. Critical film Reynolds number was identified to exist for the maximum heat and mass transfer regardless of the volumetric concentration of non-absorbable gases.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1703-1706
• /
• 1996

The purpose of this study is to research and develop polypyrrole(PPy) positive for thin film rechargeable lithium battery. We investigated cyclic voltammetry, AC impedance response and charge/discharge cycling of PPy/SPE/Li cells as a function of temperature. The redox capacity of $PPy/CF_{3}SO_{3}$ film was the most large. The discharge capacity of PPy/SPE/Li cell with $PPy/CF_{3}SO_{3}$ film was higher than those of $PPy/ClO_{4}$ and $PPy/AsF_6$ films at all cycles. The energy density of PPy/SPE/Li cells during 1st cycle was 73, 90 and 101Wh/kg at $25^{\circ}C$, $45^{\circ}C$ and $60^{\circ}C$, respectively. The improvement of energy density is due to reduction of charge-transfer resistance associated doping-undoping process in PPy film with Increasing temperature. $PPy/CF_{3}SO_{3}$ film shows a good property on charge/discharge cycling in PEO-$LiClO_4$-PC-EC electrolyte.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1414-1417
• /
• 1996

The purpose of this study Is to research and develop $V_{6}O_{13}$ composite cathode for lithium thin film battery. $V_{6}O_{13}$ represents a class of cathode active material used in Li rechargeable batteries. In this study, we investigated cyclic voltammetry and charge/discharge characteristics of $V_6O_{13}$/SPE/Li cells. Cyclic voltammogram of $V_{6}O_{13}$/SPE/Li cell at scan rate 1mV/sec showed reduction peaks of 2.25V and 2.4V and oxidation peaks of 2.4V and 2.2V. The discharge curve of $V_{6}O_{13}$/SPE/Li cell showed 4 potential plateaus. The discharge capacity was decreased in the beginning of charge/discharge cycling. After 8th cycling, the discharge capacity was stable. The discharge capacity of 1st cycle and 15th cycle was 290mAh/g and 147mAh/g at $25^{\circ}C$, respectively.

• 한국재료학회지
• /
• 제4권5호
• /
• pp.556-565
• /
• 1994

AI-Si계합금인 2090과 CP 276합금에 Ag(0-0.16wt.%)을 첨가하여 조직 및 기계적 성질에 미치는 영향을 조사하였다. Ag첨가는 결정립크기를 작게하였으며, $\delta$'($AI_{3}Li$)과 $T_{1}(AI_{2}CuLi$)석출상은 2090합금에서 미세하고 균일하게 형성되었으나 CP 276 합금에서는 변화를 보이지 않았다. Ag이 0.16wt.%함유된 2090합금의 경우 인장강도값은 약 40MPa 향상되었으며 연신율은 약간 감소하는 경향을 나타내었다. MG이 함유된 CP 276합금에서는 미량으로 첨가된 Ag에 의한 강도 및 연신율의 변화가 나타나지 않았다. $150^{\circ}C$에서 시효처리하였을 경우에 합금에 따라 70또는 90시간에서 최대 경도값 92 $H_rB$를 나타내었다.

• 한국표면공학회지
• /
• 제27권2호
• /
• pp.65-73
• /
• 1994

Effects of deposition parameter on the ionic conductivity and structural change of the Lithium borosili-cate solid electrolyte films, prepared by rf sputtering using 7$LI_2O-3B_2O_3-1SiO_2$ single phase target and also a mosaic target enriched with $LI_2O$, were analyzed by measuring AC impedance and IR absorption spectra for the films. Thed solid electrolyte film deposited from the single phase target exhibited very low ionic conductivi-ty of $10^{-10}{\Omega}^{-1}cm{-1}$ at room temperature, a result of low $Li^+$ ion content(7.52 at%) in the film. The $Li^+$ con-ductivity for the films deposited from the mosaic target, however, significantly increased to $10^{-7}{\Omega}^{-1}cm{-1}$ due to both an increased $Li^+$content (14.75 at %) and a structural change of the films. The increased ionic conduc-tivity of the film appears to be associated with an easiness of ionic mobility by structural change of glassy film from a some close packed network structure to a open one. These structural changes of film were found to be closely related to the increase in the peak intensity at~$960cm^{-1}$ of IR absorption spectra for the glassy films. With increasing either argon pressure from 3 to 21 mtorr or rf power from 2 to 3 W/$cm^2$, the $Li^+$ conduc-tivity for the films significantly increased to an order of $10^{-6}{\Omega}^{-1}cm{-1}$ due to an increase in openness of film structure, as confirmed by both an increase in the IR absorption peak intensity at ~$960cm^{-1}$ and a resultant reduction of activation energy for mobility of $Li^+$ ion.

• 한국응용과학기술학회지
• /
• 제18권3호
• /
• pp.167-173
• /
• 2001

The spinel $LiMn_{2}O_{4}$ powders were synthesized at $480^{\circ}C$ for 12 h in air by a sol-gel method using manganese acetate and lithium hydroxide as starting material and the $Fe_{3}O_{4}$ powders were synthesized by the precipitation method using $0.2M-FeSO_{4}{\cdot}H_{2}O$ and 0.5M-NaOH. The synthesized $Fe_{3}O_{4}$ powders were mixed at portion of 5, 10, 15 and 20 wt% about $LiMn_{2}O_{4}$ powders through ball-milling followed by drying at room temperature for 48 h in air. The mixed catalysts were reduced at $350^{\circ}C$ for 3 h by hydrogen and the decomposition rate of carbon dioxide was measured at $350^{\circ}C$ using the reduced catalysts. As the results of $CO_{2}$ decomposition experiments, the decomposition rates of carbon dioxide were 85% in all catalysts but the initial decomposition rates of $CO_{2}$ were slightly high in the case of the $5%-Fe_{3}O_{4}$ added catalyst.

• 전력전자학회논문지
• /
• 제25권5호
• /
• pp.376-384
• /
• 2020

An energy storage system is composed of lithium-ion batteries in modern applications. Batteries are regarded as storage devices for renewable and residual energy. The failure of batteries can cause the performance reduction and explosion of battery systems. High maintenance cost is essential when dealing with the problem of battery safety. Therefore an accurate health diagnosis is required to ensure the high reliability of battery systems. A battery pack is a combination of single cells in series and parallel connections. A battery pack has to consider various factors to assess battery health. Battery health involves conventional factors and additional factors, such as cell-to-cell imbalance. For large applications, state-of-health (SOH) can be inaccurate because of the lack of factors that indicate the state of the battery pack. In this study, six characterization factors are proposed for improving the SOH estimation of battery packs. The six proposed characterization factors can be regarded as health indicators (HIs). The six HIs are applied to the principal component analysis (PCA) algorithm. To reflect information regarding capacity, voltage, and temperature, the PCA algorithm extracts new degradation factors by using the six HIs. The new degradation factors are applied to a multiple regression model. Results show the advancement and improvement of SOH estimation.

• Corrosion Science and Technology
• /
• 제20권5호
• /
• pp.249-255
• /
• 2021

In this work, we proposed a facile method to fabricate the three-dimensional porous copper current collector (3D Cu CC) for a Si-dominant anode in a Li-ion battery (LiB). The 3D Cu CC was prepared by combining chemical etching and thermal reduction from a planar copper foil. It had a porous layer employing micro-sized Cu balls with a large surface area. In particular, it had strengthened attachment of Si-dominant active material on the CC compared to a planar 2D copper foil. Moreover, the increased contact area between a Si-dominant active material and the 3D Cu could minimize contact loss of active materials from a CC. As a result of a battery test, Si-dominant active materials on 3D Cu showed higher cyclic performance and rate-capability than those on a conventional planar copper foil. Specifically, the Si electrode employing 3D Cu exhibited an areal capacity of 0.9 mAh cm^-2 at the 300^th cycles (@ 1.0 mA cm^-2), which was 5.6 times higher than that on the 2D copper foil (0.16 mAh cm^-2).

• Restorative Dentistry and Endodontics
• /
• 제43권4호
• /
• pp.48.1-48.13
• /
• 2018

Objectives: To analyze the influence of thickness and incisal extension of indirect veneers on the stress and strain generated in maxillary canine teeth. Materials and Methods: A 3-dimensional maxillary canine model was validated with an in vitro strain gauge and exported to computer-assisted engineering software. Materials were considered homogeneous, isotropic, and elastic. Each canine tooth was then subjected to a 0.3 and 0.8 mm reduction on the facial surface, in preparations with and without incisal covering, and restored with a lithium disilicate veneer. A 50 N load was applied at $45^{\circ}$ to the long axis of the tooth, on the incisal third of the palatal surface of the crown. Results: The results showed a mean of $218.16{\mu}strain$ of stress in the in vitro experiment, and $210.63{\mu}strain$ in finite element analysis (FEA). The stress concentration on prepared teeth was higher at the palatal root surface, with a mean value of 11.02 MPa and varying less than 3% between the preparation designs. The veneers concentrated higher stresses at the incisal third of the facial surface, with a mean of 3.88 MPa and a 40% increase in less-thick veneers. The incisal cover generated a new stress concentration area, with values over 48.18 MPa. Conclusions: The mathematical model for a maxillary canine tooth was validated using FEA. The thickness (0.3 or 0.8 mm) and the incisal covering showed no difference for the tooth structure. However, the incisal covering was harmful for the veneer, of which the greatest thickness was beneficial.

• 한국산학기술학회논문지
• /
• 제19권12호
• /
• pp.600-606
• /
• 2018

금속화재는 나트륨(Na), 리튬(Li) 등과 같은 가연성 금속이 연소하는 화재이다. 일반적인 물계, 가스계 소화약제에는 적응성이 없으며 금속화재용 소화약제 또는 건조사로 화재를 진화할 수 있다. 위험물안전관리법상 가연성 금속에 속하는 2류 및 3류 위험물 화재가 최근 5년간 104건이 발생했으며, 가연성 금속을 사용하는 연료전지, 반도체 산업의 발전으로 화재 건수는 더욱 증가할 것으로 예상되고 있다. 하지만 국내에는 금속화재와 관련된 법적 기준이 마련되어 있지 않아 금속화재용 소화약제 및 소화기 개발은 물론 화재 예방 및 대응 시스템 구축이 이루어지지 않고 있다. 이에 본 연구에서는 금속화재의 위험성을 감소시킬 수 있는 방안을 마련하기 위해 국내외 관련 법령 분석 및 금속화재 사례 11건을 분석하였다. 이를 통해 금속화재의 위험성을 감소를 위해 관련 법령 마련에 필요한 요소를 도출하였으며 금속화재 발생 시 소화약제로 사용되고 있는 건조사의 관리 및 지원방안을 제시하였다. 또한, 금속화재의 예방 및 대응에 필요한 안전교육 및 시설 관리 방안을 제시하였다.