• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.57-66
• /
• 2016

In this study, to prevent possible collapse caused by hydraulic or mechanical instability, liquid nitrogen injection method is developed and implemented at the tip of drilling auger of steel pipe propulsion tunneling. In this study, 1/5-scale model auger and sand chamber were manufactured. The prototype diameter of steel pile (or casing) is assumed about 1,000 mm. For the frictional sandy soils and plastic weathered soils, liquid nitrogen injection methods were tested varying water contents of the soils. For the induced hydraulic instability, the ground near the drilling auger was frozen within approximately 5 minutes preventing mechanical collapse and water infiltration. Securing stability of steel pile propulsion tunneling using liquid nitrogen was much more effective for which the water content of the soil somewhat exceeds the optimum water content.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.39 no.1
• /
• pp.1-10
• /
• 2012

The concept of resin infiltration which was born in an innovative philosophy to arrest the incipient caries. However, the structural changes of resin infiltrated lesions have not yet explained completely. The liquid resin might contribute not only to maximizing the penetration but to deteriorating physical stability. This study was performed to examine some physical and histological features of resin infiltrated incipient carious lesions. With the specimen of resin infiltrated lesions, microhardness by nanoindentation in depth profile, morphology of resin tags were revealed after HCl dissolution, and degree of microleakage were assessed. The percentage of microhardness of surface layer and lesion body of untreated specimen to sound enamel was 64.6% and 24.6% respectively, while that of resin-infiltrated lesions was 72.1%, showing significant difference (p<0.05). The resin tags observed under SEM had relatively homogeneous length of 433(282~501) ${\mu}m$ on the average. Among 20 specimens for microleakage assessment, 13 specimens showed no leakage while 5 and 2 showed leakage into outer and inner half of lesion respectively. It was thought the infiltrant resin penetrates deeply and homogeneously into lesion body and improves its hardness with relatively good physical stability.

• Journal of Environmental Science International
• /
• v.22 no.12
• /
• pp.1661-1669
• /
• 2013

This study conducted a laboratory simulation using artificial and natural rainfall in order to investigate the runoff characteristics of livestock resources through the analysis of the surface runoff water and infiltration water by rainfall intensity and fertilization level. Cattle manure and pig liquid fertilizer was used as livestock resource. As a result of this study, it was observed that the surface runoff occurred over 32 mm/hr rainfall intensity, and flow rate of the surface runoff water and the runoff ratio of contaminant parameters from livestock resource was increased, as rainfall intensity was stronger. With doubled fertilization level, T-N increased in compost and the amount of $COD_{Mn}$ runoff also considerably increased in liquefied fertilizer. In the case of natural rainfall, the runoff ratio of T-P clearly increased in compost and the T-N of final surface runoff ratio in compost and liquefied fertilizer was ranged from 0.13047 to 0.13623 with stronger rainfall intensity.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.875-884
• /
• 2023

Hydrogen infiltration into metals has been reported to induce alterations in their mechanical properties under load. In this study, we conducted CTOD (Crack Tip Opening Displacement) tests on steel specimens designed for use in liquid hydrogen storage systems. Electrochemical hydrogen charging was performed using both FCC series austenitic stainless steel and BCC series structural steel specimens, while CTOD testing was carried out using a 500kN-class material testing machine. Results indicate a notable divergence in behavior: SS400 test samples exhibited a higher susceptibility to failure compared to austenitic stainless steel counterparts, whereas SUS 316L test samples displayed minimal changes in displacement and maximum load due to hydrogen charging. However, SEM (Scanning Electron Microscopy) analysis results presented challenges in clearly explaining the mechanical degradation phenomenon in the tested materials. This study's resultant database holds significant promise for enhancing the safety design of liquid hydrogen storage systems, providing invaluable insights into the performance of various steel alloys under the influence of hydrogen embrittlement.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.288-292
• /
• 2011

In this study, we investigated the mechanical behavior of carbon fiber reinforced silicon carbide composites by indentation stress. Relatively porous and dense fiber reinforced ceramic composites were fabricated by liquid silicon infiltration (LSI) process. Densification of fiber composite was controlled by hardening temperature of preform and consecutive LSI process. Load-displacement curves were obtained during indentation of WC sphere on the carbon fiber reinforced silicon carbide composites. The indentation damages at various loads were observed, and the elastic modulus were predicted from unloading curve of load-displacement curve.

• Tribology and Lubricants
• /
• v.24 no.4
• /
• pp.163-169
• /
• 2008

Tribological properties of ceramic brake discs were investigated using a commercial friction material. The discs were manufactured by liquid silicon infiltration (LSI) into a C-C preform. The disc surface was modified by two different methods, producing sliding surfaces with chopped carbon fibers and carbon felt. In addition, the composition of the surface was also changed. Friction characteristics of the discs were examined using a 1/5 scale dynamometer. Results showed that the type and composition of the disc surface significantly affected the level of braking effectiveness and high temperature brake performance. The discs with felt surfaces showed higher friction levels than those with chopped fiber surfaces and SiC tended to increase the friction level while C lowered the friction coefficient. The ceramic disc was more sensitive to the deceleration rate than gray iron, showing high speed sensitivity.

• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1561-1569
• /
• 1994

Effect of calcining temperature on the sintering behaviors and microwave dielectric properties of BMT[Ba(Mg1/3Ta2/3)O3] ceramics was studied. The calcining temperatures were varied from 80$0^{\circ}C$ to 130$0^{\circ}C$, respectively. It was found that, as calcining temperature lowered below 125$0^{\circ}C$, second phase such as Ba5Ta4O15 phases started to appear in calcined powder with unreacted powders. After sintering, exaggerately grown Ba5TaO3 phase could be found amang the uniform BMT grains in sintered body. Basis on the infiltration experiment, Ba0.05TaO3 phase should be formed by reaction of BMT grain and BaO-MgO eutectic liquid. But increase of calcining temperature above 125$0^{\circ}C$, there was not any second phase or unreated component in calcined powder and sintered body. As result, low calcining temperature led to precipitation of second phase in specimen and resulted decrease of Q value of BMT ceramics.

• Journal of Yeungnam Medical Science
• /
• v.21 no.2
• /
• pp.215-223
• /
• 2004

Silicone is widely used for medical purposes in breast augmentation and other cosmetic procedures. Illegal injections of silicone in human beings might have adverse effects and one of the serious problems is a silicone embolism. We experienced five cases of unusual respiratory difficulties after an injection of liquid silicone in the breast, vagina, uterus, and hip. They were all young adult females, who were previously healthy. One of them died after the injection. The three remaining patients were admitted because of dyspnea, coughing, chest discomfort and bilateral pulmonary infiltration after the silicone injection. A transbronchial lung biopsy and autopsy disclosed many oil like materials filling the alveolar septal capillaries. Three patients underwent a computed tomogram (CT), which revealed multifocal airspace consolidations at the peripheral and nondependent portions of both lungs, which is a different finding from other thromboembolisms. Lung scans of the disclosed abnormalities were compatible with silicone induced pulmonary embolism.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.441-449
• /
• 1993

SiC particulate reinforced magnesium matrix composites were fabricated by melt stirring method. The effet of several factors on mechanical properties and the efficiency of melt stirring method from the viewpoint of these properties were investigated. The tensile strength increased and the elongation decreased with decrease of the particle size or the increase of the paticulate volume fraction for pure magnesium matrix and Mg-5%Zn alloy matrix composites. A longer stirring time improved the tensile strength of these composites. The tensile strength of Mg-5%Ca alloy matrix composites which shows no uniform paticulate distribution was a little lower than that of matrix alloy. Rapid solidification rate is preferred for the improved tensile strength of these composites. The pure magnesium matrix and Mg-5%Zn alloy matrix composites have tensile strength of about 400MPa. This value agrees with the tensile strength of some magnesium matrix composites fabricated by liquid infiltration method or powder metallurgy method at the same volume fraction of reinforcements of whisker or particle. Therefore, the melt stirring method which has the advantages of simple process is considered to be efficient in fabricating magnesium matrix composites.

• Journal of the Korean Society of Safety
• /
• v.28 no.3
• /
• pp.74-79
• /
• 2013

As the feature of fire, it is hard for deep-seated fire to spread to the deeper site, and it also has danger for being re-ignited cause of recontacting with oxygen after being put off. Now it is ruled in the certification criteria of wetting agent used for extinguishing deep-seated fire that the criteria for surface tension is below 33[mN/m] in Korea. For figuring out how much water for fire-fighiting can permeate into combustibles, in this research, the permeating performance is analyzed by measuring the speed of permeating and transmission quantity released after that, by pouring solution whose surface tension is changed by adjusting concentration of surfactant BDG(Butyl Di Glycol) in column From this result, it is can be determined that transmission quantity becomes less and wet area goes wider as surface tension is lower, and it is also able to be analyzed as quantity of absorbed liquid and wet area is increased because fluid permeates into the core.