• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.63-72
• /
• 1990

Surface of crystalline silica was sequentially reacted with silane(A 187), liquid rubber(CTBNx8) and vinyl monomer(AA, MMA, 2-HEA, GMA) in existance of amines(TEA, CTMAB, BETAC) or peroxide(BPO). By mixing it with epoxy resin at a ratio 0~36%(volume %) of total component, liquid properties of mixtures was investigated experimentally. i) Coating ratio depended on quantity and sorts of catalyst. ii) Total coating of 2.5~5.8% was attained by using 0.1~2.0% of catalyst. iii) Treated surfaces represented each different features in according to sorts of treatment. iv) Silane/rubber or silane/rubber/vinyl represented lower viscosity and settling than non-treated or silane-treated.

• 연구논문집
• /
• s.30
• /
• pp.111-119
• /
• 2000

Sintering of alumina powder was studied in the presence of Y-Si oxide and oxynitride additives. The main crystalline phase of the sintering aids pre-reacted at $1400^{\circ}C$ was $\alpha$ - $Y_2$$SiO_2$>$O_7$. Y-N apatite was co-existed in the Si-40N sintering aid because of its high content of N. During the sintering process, liquid phases were formed by the reaction between additives and alumina, and these liquid phases promote the densification of alumina. SEM micrographs showed that uniform grain growth occurred in the system with oxide additive(Si-0N). In the case of oxynitride additive system(Si-20N and Si-40N), bimodal microstructure was observed due to the exaggerated grain growth, As the nitrogen content in the additive system increased the exaggerated grain growth occurred extensively. Bloating, which seemed to be originated by the liberation of $N_2$ gas, occurred un the Si-40N oxynitride additive system.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.3
• /
• pp.102-106
• /
• 2015

The performance of Li-B alloy as anode for molten salt electrolysis was firstly investigated. The crystalline phase of the prepared Li-B alloy was identified as $Li_7B_6$. The potential profile of Li-B alloy anode was monitored during the electrodeposition of $Nd^{3+}$ onto an LCC (liquid cadmium cathode) in molten LiCl-KCl salt at $500^{\circ}C$. The potential of Li-B alloy was increased from -2.0 V to -1.4 V vs. Ag/AgCl by increasing the applied current from 10 to $50mA{\cdot}cm^{-2}$. It was found that not only the anodic dissolution of Li to $Li^+$ but also the dissolution of the atomic lithium ($Li^0$) into the LiCl-KCl eutectic salt was observed, following the concomitant reduction of $Nd^{3+}$ by the $Li^0$ in Li-B alloy. It was expected that the direct reduction could be restrained by maintaining the anode potential higher that the deposition potential of neodymium.

• Journal of Powder Materials
• /
• v.28 no.1
• /
• pp.51-58
• /
• 2021

The conversion of carbon preforms to dense SiC by liquid infiltration is a prospectively low-cost and reliable method of forming SiC-Si composites with complex shapes and high densities. Si powder was coated on top of a 2.0wt.% Y2O3-added carbon preform, and reaction bonded silicon carbide (RBSC) was prepared by infiltrating molten Si at 1,450℃ for 1-8 h. Reactive sintering of the Y2O3-free carbon preform caused Si to be pushed to one side, thereby forming cracking defects. However, when prepared from the Y2O3-added carbon preform, a SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C → SiC reaction at 1,450℃, 3C and 6H SiC phases, crystalline Si, and Y2O3 were generated based on XRD analysis, without the appearance of graphite. The RBSC prepared from the Y2O3-added carbon preform was densified by increasing the density and decreasing the porosity as the holding time increased at 1,450℃. Dense RBSC, which was reaction sintered at 1,450℃ for 4 h from the 2.0wt.% Y2O3-added carbon preform, had an apparent porosity of 0.11% and a relative density of 96.8%.

• Composites Research
• /
• v.35 no.2
• /
• pp.53-60
• /
• 2022

This study uses Diglycidyl ether of terephthalylidene-bis-(4-amino-3-methylphenol) (DGETAM), an amine hardener 4,4'-diaminodiphenylethane (DDE) and cationic catalyst N-benzylpyrazinium hexafluoroantimonate (BPH) to make epoxy film. For analysis, ¹H_NMR and FT-IR were used to verify proper synthesis, and the liquid crystallinity of DGETAM was checked using Differntial Scanning Calorimetry and Polarized Optical Microscopy. Thermal conductivity of the sample was measured using Laser Flash Apparatus. Thermal stability as well as thermal conductivity is important when used as a packaging material. Activated energy is the energy needed to generate a response, which can be used to estimate the energy required to maintain physical properties. It was obtained using the Arrhenius equation based on the data measured by isothermal decomposition using Thermogravimetric Analysis. Measurement of the thermal conductivity of epoxy films showed higher thermal conductivity when DDE was used, and it was found that thermal conductivity had an effect on thermal stability, given that it represented an activation energy similar to a film with BPH upon 5% decomposition.

• Korean Journal of Materials Research
• /
• v.31 no.5
• /
• pp.301-311
• /
• 2021

The conversion of all carbon preforms to dense SiC by liquid infiltration can become a low-cost and reliable method to form SiC-Si composites of complex shape and high density. Reactive sintered silicon carbide (RBSC) is prepared by covering Si powder on top of 0.5-5.0 wt% Y₂O₃-added carbon preforms at 1,450 and 1,500℃ for 2 hours; samples are analyzed to determine densification. Reactive sintering from the Y₂O₃-free carbon preform causes Si to be pushed to one side and cracking defects occur. However, when prepared from the Y₂O₃-added carbon preform, an SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C = SiC reaction, 3C and 6H of SiC, crystalline Si, and Y₂O₃ phases are detected by XRD analysis without the appearance of graphite. As the content of Y₂O₃ in the carbon preform increases, the prepared RBSC accelerates the SiC conversion reaction, increasing the density and decreasing the pores, resulting in densification. The dense RBSC obtained by reaction sintering at 1,500 ℃ for 2 hours from a carbon preform with 2.0 wt% Y₂O₃ added has 0.20 % apparent porosity and 96.9 % relative density.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.855-859
• /
• 2023

Copper oxide (CuO) nanoparticles were successfully synthesized using a precursor in which industrial starch was impregnated with an aqueous solution of copper (II) nitrate trihydrate. The microstructure of the precursor impregnated with an aqueous solution of copper nitrate trihydrate was confirmed with a scanning electron microscope (SEM), and the particle size and the crystal structure of the copper oxide particles produced as the temperature of the heat treatment of the precursor increased was analyzed by X-ray diffraction (XRD) and the scanning electron microscope (SEM). As a result of the analysis, it was confirmed that the temperature at which the organic matter of the precursor is completely thermally decomposed is 450-490℃, and that the size and crystallinity of the copper oxide particles increased as the heat treatment temperature increased. The size of the copper oxide particles obtained through heat treatment at 500-800℃ during 1 hour was 100nm~2㎛. It was confirmed that the copper oxide crystalline phase is formed at a heat treatment temperature of 400℃, and only the copper oxide single phase existed up to 800℃. And it was also confirmed that the size of particles produced increased as the calcination temperature increased.

• Macromolecular Research
• /
• v.8 no.1
• /
• pp.12-18
• /
• 2000

Six aromatic polyesters with ether-linkages were prepared from 4,4'-oxybis(benzoic acid) and naphthalenediol (ND) isomers which were 1,4-, 1,5-, 1,6-, 2,3-, 2,6- and 2,7-derivatives. The solution viscosity numbers ranged from 0.23 to 0.65 dL/g. The glass transition temperatures ranged from 142 to 179$\^{C}$. The initial decomposition temperatures were all above 400$\^{C}$, and the residue weights at 600$\^{C}$ were in the range of 50-64%. Only the polyesters derived from 1,5- and 2,6-NDs, which have a linear linking mode, were found to be semicrystalline and could form thermotropically nematic phase. Multiple melting phenomena and annealing of the polyester derived from 1,5-ND and related polymers are described. The experimental results show that the polyester derived from 1,4-ND of linear shape was amorphous and non-liquid crystalline. Particularly, the polyester derived from 2,3-ND could form a smectic mesophase as banana-shaped molecules, and this is ascribed to the C/sub_2v/ symmetry where highly kinked molecules are packed in the same direction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.156-156
• /
• 2009

전자기기의 Slim화에 따라 부품 일장용 Board 기판의 두께도 날로 감소해지고 있다. 이와는 정 반대로 기판의 층수는 더 늘어나고 있다. 이에 따라 기판의 구성요소인 절연재의 두께도 감소하고 있다. 전자기기는 각각의 Module이 저항을 가지는데 이를 matching하기 위해서 각 module이나 package가 가지는 저항값을 상호 비슷하게 맞춘다. 하지만, 기판의 절연재의 두께 감소는 이러한 저항값이 낮아지게 한다. 이렇게 낮아진 저항값을 높이기 위해서는 전도체의 폭을 줄여야 한다. 하지만, 이렇게 전도체의 폭을 줄이는 것은 기판 제작 비용의 상승 및 제작 물가에 이르게 할 수 있다. 이를 해결하기 위해서는 절연재의 유전율을 낮추는 것이 가장 효과적이다. 본 연구에서는 PCB 기판의 유전율을 낮추기 위해 Liquid Crystalline Polymer(LCP)에 PTFE powder를 넣어 기판 재료의 가능성을 조사하였다. 유전율은 PTFE의 첨가량이 증가함에 따라 감소하여 40wt% 첨가할 경우 유전율이 2.4 정도로 낮아졌다. 이에 반해 열팽창계수는 증가가 크지 않고 peel strength는 감소함을 알 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.362.1-362.1
• /
• 2016

InAs nanowires were synthesized by a vapor-liquid-solid method with InAs powder. The composition and crystalline structure of nanowires were confirmed by energy-dispersive spectroscopy (EDS) and high resolution transmission electron microscopy (HRTEM), respectively. The thermal conduction of nanowires was investigated by the optical method using Raman spectroscopy: i.e., the local temperature on nanowire was determined by laser heating. As temperature increased, the Raman peaks are shifted to low frequency and broadened. The temperature dependent Raman scattering experiments was realized on InAs nanowires with different percentages of zinc-blende and wurtzite structure. The temperature dependence on the nanowire structure has been successfully obtained: the phonon scattering was more increased in InAs heretostructure nanowires, compared to the InAs nanowires with homostructure. The result strongly suggests that the thermal conduction can be effectively controlled by ordered interface without any decrease in electrical conduction.