• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.7
• /
• pp.517-524
• /
• 2019

A system design has been performed for a vacuum thrust 88 ton staged combustion cycle rocket engine. Previous research has been used to estimate the performance of the engine components. And the algorithm has been proposed to evaluate the converged engine system performance. The present methodolgy has been verified by comparing the published data for RD-180. The present work adopts the most of the previous KSLV-II engine heritage for both performance improvement and cost competitiveness. The combustion pressure has been decided as 12MPa considering manufacturing difficulty, cost and performance improvement, and as a result the vacuum specific impulse has increased by 23.4s.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.205-210
• /
• 2007

A LOX pump rotordynamic design was performed for a 75 ton thrust liquid rocket engine. Axial positions of an inducer, an impeller and bearings on a shaft are decided on the basis of the experience achieved by previously developed turbopump which has the similar layout. The result of pump hydraulic design was reflected in the present study to decide axial length of the inducer and impeller. A distance from the rear bearing to the impeller was considered as a design parameter for load distribution of the bearings. Asynchronous eigenvalue analysis was performed as a function of rotating speeds and bearing stiffness to investigate critical speed of the LOX pump. From the numerical analysis, it is found that the LOX pump with the proper bearing loads safely operates as a sub-critical rotor of which critical speed is high enough compared to the operating speed 11,000 rpm.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.250-257
• /
• 2001

Low NPSH and high pressure pumps are widely used for turbopump systems, which have an inducer and operate at high rotating speeds In this paper, a meanline method has been established for the preliminary design and performance prediction of pumps having an inducer for cavitating or non-cavitating conditions and at design or off-design points. The method was applied for the performance prediction of a fuel pump, which had been developed by Hyundai Mobis in collaboration with KeRC for a liquid rocket engine. The engine uses liquid methane and liquid oxygen as working fluids and rotates at 50,000 rpm KeRC carried out a model testing of the fuel pump with water as a working fluid at the reduced speed (10,000 ${\~}$ 15,000 rpm). Predicted performances by the method are shown to be in good agreement with experimental results for cavitating and non-cavitating conditions. The established meanline method can be used for the performance prediction and preliminary design of high speed pumps which have a inducer, impeller and volute.

• Journal of Aerospace System Engineering
• /
• v.11 no.1
• /
• pp.8-13
• /
• 2017

This study was performed to evaluate the turbine performance of a turbopump in the third stage engine of the Korea Space Launch Vehicle-II. The turbine is a supersonic impulse type with a single rotor. One nozzle is for starting and four remaining nozzles are for steady operation. A similarity test was carried out in the high air test facilities at the Korea Aerospace Research Institute. Test results showed that turbine efficiency changed much more from rotational speed variations than by pressure ratio variations. These results showed characteristics similar to other supersonic impulse turbines.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.145-152
• /
• 2000

A turbopump system composed of two pumps and one turbine is considered. The turbine composed of a nozzle and a rotor is used to drive the pumps while gas passes through the nozzle, potential energy is converted to kinematic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of turbine system is investigated using compressible fluid dynamic theories with some pre-determined design requirements (i.e., pressure ratio, rotational speed, required power etc.) obtained from liquid rocket engine (L.R.E.) system design. For simplicity of turbine system, impulse-type rotor blades for open type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow rate compared to close-type system. In this study, a partial admission nozzle Is adopted to maximize the efficiency of the open-type turbine system. A design methodology of turbine system has been introduced. Especially, partial admission nozzle has been designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design for a 10 ton thrust level of L.R.E is presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1132-1138
• /
• 2008

A program that can simulate gas generator after burning liquid rocket engines was developed along with presenting the characteristics of the engines. The program was written in Matlab and used GUI interface so that many users can use it without any difficulties. The results of the program was compared with the real engine which was developed by the LRE advanced country. Most of the parameters concurred within 1% error expect for the pressure at the turbopump. The reasons of the large differences were supposed that pressure decreases at the schematics were smaller than that of the real engines.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.5
• /
• pp.73-78
• /
• 2008

The development of turbopump in Korea has been practically started from 1999. Recently, the turbopump for a LRE with 30-ton level thrust has been successfully developed, which is able to work for all the required LRE regimes. This success is considered as a breakthrough in development of LRE because the turbopump, a core component of LREs, has been considered as a critical barrier in domestic technology point of view. In this paper, status of the turbopump development in Korea is provided and some suggestions are made for the prospective future.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.347-351
• /
• 2004

The cryogenic test facility is developed for test of deep groove ball bearings, floating ring seals, materials (steel & copper) for High Pressure Turbopump of liquid rocket engine (LRE). The cryogenic bearing test is performed to evaluate the flow rate of cooling water and the load-carrying capacity of bearings. The cryogenic seal test is performed to evaluate the determination of magnitude of leakages through the seal, a time variation of this magnitude. The test of the materials Pair is performed to evaluate its fitness for operation in the liquid oxygen medium.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.343-346
• /
• 2010

The construction plan of a combustion chamber test facility(CTF), a turbopump real propellant test facility(TPTF), a rocket engine ground/high altitude test facility(ReTF, HAReTF) and a propulsion system test complex(PSTC) for KSLV-II is briefly described. The development/qualification tests of 75ton-class liquid rocket engine system and engine component will be performed in CTF, TPTF, ReTF and HAReTF and the development test of $1^{st}/2^{nd}/3^{rd}$ propulsion systems for KSLV-II will be performed in PSTC. These propulsion test facilities will be built in NARO space center considering construction schedule, cost, safety distance and utility factor of propulsion test facilities.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.60-71
• /
• 2007

The startup characteristic of liquid propellant rocket engine should be focused on the stable ignition of combustion chamber and gas generator. Also, to lessen the propellants consumption during this period which doesn't contribute to the flight thrust, the engine has to be transferred to the nominal mode quickly. Because of the risk of test, it is impossible to develop all the startup cyclogram or the specifications of engine by test, so the precedent numerical approach is quite necessary. In this study we developed a mathematical model for the startup phenomena in a liquid rocket engine driven by gas generator-turbopump system based on the commercial 1-D flow system analysis program, Flowmaster. Using this program we proposed a methodology to obtain the specifications of turbine starter and the opening time of shutoff valves for the stable startup of the engine. To verify this methodology we qualitatively compared the analysis results to the typical startup curve of the published engine, then found it is quite well matched.