• Bulletin of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.718-724
• /
• 2006

The heterogeneous association behaviour of various concentration binary mixtures of mono alkyl ethers of ethylene glycol with ethyl alcohol were investigated by dielectric measurement in benzene solutions over the entire concentration range at 25 ${^{\circ}C}$. The values of static dielectric constant $\epsilon_0$ of the mixtures were measured at 1 MHz using a four terminal dielectric liquid test fixture and precision LCR meter. The high frequency limiting dielectric constant $\epsilon_\infty$ values were determined by measurement of refractive index $n_D$ ($\epsilon_\infty\;=\;n_D\;^2$). The measured values of $\epsilon_0$ and $\epsilon_\infty$ were used to evaluate the values of excess dielectric constant $\epsilon^E$, effective Kirkwood correlation factor $g^{eff}$ and corrective correlation factor $g_f$ of the binary polar mixtures to obtain qualitative and quantitative information about the H-bond complex formation. The non-linear behaviour of the observed $\epsilon_0$ values of the polar molecules and their mixtures in benzene solvent confirms the variation in the associated structures with change in polar mixture constituents concentration and also by dilution in non-polar solvents. Appearance of the maximum in $\epsilon^E$ values at different concentration of the polar mixtures suggest the formation of stable adduct complex, which depends on the molecular size of the mono alkyl ethers of ethylene glycol. Further, the observed $\epsilon^E$ < 0 also confirms the heterogeneous H-bond complex formation reduces the effective number of dipoles in these polar binary mixtures. In benzene solutions these polar molecules shows the maximum reduce in effective number of dipoles at 50 percent dilutions. But ethyl alcohol rich binary polar mixtures in benzene solvent show the maximum reduce in effective number of dipoles in benzene rich solutions.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.311-313
• /
• 2014

High pressure combustion with multiphase--liquid, gas, and supercritical phase--mixtures are widely used technology in the high efficiency liquid propellent rocket engine. This is the typical characteristics differentiate from the combustor of conventional air-breathing engines. Therefore, successful research of high pressure combustion at supercritical condition is essential to develope a high efficiency liquid rocket engine. Numerical studies have been carried out to explore capabilities of numerical method for LOx-CH4 non-premixed flames at high pressure. In this paper, corresponding numerical results are presented and compared with experimental result of MASCOTTE facility.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.200-202
• /
• 2007

Improvement of LC mixtures can be realized by the development of new molecules in combination with the identification of advanced mixture concepts. By new high-polar single materials rotational viscosity has recently been improved significantly. Now, a new LC mixture concept for IPS and FFS technology has been identified which additionally improves switching time by up to 10%. This advanced concept is based on a more efficient usage of high-polar materials and Super Low Viscous (SLV) compounds and simultaneous reduction of less efficient materials.

• Bulletin of the Korean Chemical Society
• /
• v.11 no.6
• /
• pp.508-511
• /
• 1990

The simple binary mixtures of pure phospholipids such as DPPC:DSPC and DPPC:DPPA were investigated with differential scanning calorimeter. The thermotropic properties of DPPC and DSPC mixtures did not deviate much from the ideal curves that was obtained on varying either the temperature or the relative proportions of phospholipids. This means that the two phospholipids are completely miscible in the liquid and solid phase. But the thermotropic properties of DPPC and DPPA mixture deviated much from the ideal phase diagram. It resulted from the repulsion between the head groups of acidic phospholipids. Heat capacity suggested by Harden McConell was calculated. The larger $C_p$ was, the sharper the endothermic peak became.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.924-929
• /
• 2002

We have developed the novel liquid crystal materials with a difluoromethyleneoxy (CF2O) moiety as a linkage group in order to satisfy the diversified various requirements for AM-LCDs. These novel CF2O LC materials have excellent physical properties that are high dielectric anisotropy, low viscosity and wide nematic temperature ranges. Physical properties measurement results that mixtures containing CF2O LC materials have suitable for characteristics for AM-LCDs. The CF2O LC materials are excellent compound for quick response and low driving voltage application.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.156-158
• /
• 2009

New liquid crystal (LC) host mixtures and reactive mesogens (RMs) designed for the Polymer Sustainable Vertically Aligned (PS-VA) mode have been developed. The novel combination of LC host mixture with RMs enables to show superior LC display performance with high reliability and to contribute for the robust LC panel production process.

• Korean Membrane Journal
• /
• v.2 no.1
• /
• pp.36-47
• /
• 2000

This paper deals with the separation of MTBE-methanol mixtures using crosslinked Poly(vinyl alcohol)(PVA) membranes with sulfur-succinic acid(SSA) as a crosslinking agent by pervaporation and vapor permeation technique. The operating temperatures, methanol concentration in feed mixtures, and SSA concentrations in PVA membranes were varied to investigate the separation performance of PVA/SSA membranes and the optimum separation characteristics by pervaporation and vapor permeation. And also, for PVA/SSA membranes, the swelling measurements were carried out to study the transport phenomena. The swelling measurements were carried out for pure MTBE and methanol, and MTBE/methanol=90/10, 80/20 mixtures using PVA/SSA membranes with varying SSA compositions. There are two factors of the membrane network and the hydrogen bonding. In pervaporation separation was also carried out for MTBE/methanol=90/10, 80/20 mixtures at various temperatures. The sulfuric acid group in SSA took an important role in the membrane performance. The crosslinking effect might be over the hydrogen bonding effect due to the sulfuric acid group at 3 and 5% SSA membranes, and this two factors act vice versa on 7% SSA membrane. In this case, the 5% SSA membrane shows the highest separation factor of 2,095 with the flux of 12.79g/㎡$.$hr for MTBE/methanol=80/20 mixtures at 30$^{\circ}C$ which this mixtures show near the azeotopic composition. Compared to pervaporation, vapor permeation showed less flux and similar separation factor. In this case, the flux decreased significantly because of compact structure and the effect of hydrogen bonding. In vapor permeation, density or concentration of methanol in vaporous feed is lower than that of methanol in liquid feed, as a result, the hydrogen bonding portion between the solvent and the hydroxyl group in PVA is reduced in vapor permeation. In this case, the 7% SSA membranes shows the highest separation factor of 2,187 with the flux of 4.84g/㎡$.$hr for MTBE/methanol=80/20 mixtures at 30$^{\circ}C$.

• Membrane Journal
• /
• v.2 no.1
• /
• pp.36-36
• /
• 1992

This paper deals with the separation of MTBE-methanol mixtures using crosslinked Poly(vinyl alcohol)(PVA) membranes with sulfur-succinic acid(SSA) as a crosslinking agent by pervaporation and vapor permeation technique. The operating temperatures, methanol concentration in feed mixtures, and SSA concentrations in PVA membranes were varied to investigate the separation performance of PVA/SSA membranes and the optimum separation characteristics by pervaporation and vapor permeation. And also, for PVA/SSA membranes, the swelling measurements were carried out to study the transport phenomena. The swelling measurements were carried out for pure MTBE and methanol, and MTBE/methanol=90/10, 80/20 mixtures using PVA/SSA membranes with varying SSA compositions. There are two factors of the membrane network and the hydrogen bonding. In pervaporation separation was also carried out for MTBE/methanol=90/10, 80/20 mixtures at various temperatures. The sulfuric acid group in SSA took an important role in the membrane performance. The crosslinking effect might be over the hydrogen bonding effect due to the sulfuric acid group at 3 and 5% SSA membranes, and this two factors act vice versa on 7% SSA membrane. In this case, the 5% SSA membrane shows the highest separation factor of 2,095 with the flux of 12.79g/㎡·hr for MTBE/methanol=80/20 mixtures at 30℃ which this mixtures show near the azeotopic composition. Compared to pervaporation, vapor permeation showed less flux and similar separation factor. In this case, the flux decreased significantly because of compact structure and the effect of hydrogen bonding. In vapor permeation, density or concentration of methanol in vaporous feed is lower than that of methanol in liquid feed, as a result, the hydrogen bonding portion between the solvent and the hydroxyl group in PVA is reduced in vapor permeation. In this case, the 7% SSA membranes shows the highest separation factor of 2,187 with the flux of 4.84g/㎡·hr for MTBE/methanol=80/20 mixtures at 30℃.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.414-422
• /
• 1999

SBR, polyurethane and epoxy latex were separately blended with ethylene-vinyl acetate(EVA) emulsion In $0{\sim}50%$. EVA emulsion was not reacted with latexes in liquid phase and mixtures had good stroage stability. The viscosity of cement mixtures was elevated to 20,000cps in $0.5{\sim}2.0$ hours by mixing. The mixtures mixed with pigment represented high viscosity and showed higher viscosity as time goes by. Mixtures had higher hardness with mixing SBR than mixing epoxy or urethane. The hardness was suddenly increased over cement content 30%. showed pencil hardness $H{\sim}2H$ in $50{\sim}60%$. The increase of hardness in high solids was depended upon not only the condensation of latexs but also the coagulation and adhesion of cement particle.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.513-518
• /
• 2005

The co-pyrolysis characteristics of poly(vinyl chloride) (PVC) and polystyrene (PS) mixtures with ZnO have been studied by thermogravimetry (TG) and gas chromatograph-mass spectrometry (GC-MS) under various mixing ratios and reaction temperatures. From this work, it was found that the yield of liquid products increased as PS in mixtures increased, whereas that of gaseous products decreased. And as ZnO in mixtures increased, the yields of gaseous products and HCI decreased. The optimal reaction temperature for the maximum yield of liquids products and the control of HCI gas was $500^{\circ}C$.