• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.193-197
• /
• 2004

The effect of the temperature dependence of the smectic layer spacing in the smectic-A (SmA) phase on the formation of defects in the ferroelectric smectic-$C^{\ast}$ ($SmC^{\ast}$) phase is investigated with x-ray scattering technique. The study is based on thin parallel-aligned surface stabilized ferroelectric liquid crystal cells with two different alignment conditions, high pretilt $SiO_x$, alignment and low pretilt polyimide films. It is found that defects observed in the $SmC^{\ast}$ phase have much more profound dependence on the layer changes and chevron formation in the SmA phase than in the $SmC^{\ast}$ phase. We find that thermal layer expansion with decreasing temperature in the SmA phase suppresses the formation of defects observed in the SmC phase.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1095-1099
• /
• 2004

We investigated the electro-optica](EO) performances of the super twisted nematic liquid crystal display(STN-LCD) on the polyimide(PI) surface using polymer film. The NLC(Nematic Liquid Crystal) pretilt angles generated are about 18$^{\circ}$by the rubbing alignment method on thin plastic substrates. However, the pretilt angle are at about 13$^{\circ}$ lower on the glass substrate than on thin plastic substrate. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance(V-T) curve of the plastic STN-LCD was observed on the polyimide(PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide(PI) surfaces using polymer film can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.4
• /
• pp.336-340
• /
• 2001

We have investigated the generation of pretilt angle and alignment stability for a nematic liquid crystal (NLC) with obliquely polarized UV exposure on the three kinds of photo-polymer. High pretilt angle of the NLC was obtained by polarized UV exposure on a PM4Ch surface for 1 min. But, the low pretilt angle of he NLC on a PVCi surface was observed. The pretilt angle generated is attributed ot the photosensitivity by the long side chaining of photo-polymer. Also, a good thermal stability of the three kinds of photo-polymer were obtained by thermogravimetric analysis (TGA) measurement until 300$^{\circ}C$. Finally, the good LC aligning capabilities using the photodimerization method were observed by annealing-treatment until 150$^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.871-875
• /
• 2000

Effects of liquid crystal (LC) alignment using a in-situ photoalignment method by polarized UV exposure on a polyimide (PI) surface with medium side chain were studied. The generated pretilt angle in nematic(N) LC using a in-situ photoalignment method was smaller than that of a conventional photoalignment method for short UV exposure time. Also, the pretilt angle of NLC using a in-situ photoalignment method increases with increasing UV exposure time on the PI surfaces. Finally, the pretilt angle of NLC can be improved by annealing treatment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.80-83
• /
• 2003

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with in-situ photoalignment method on polyimide (PI) surfaces using thin plastic substrates. The LC aligning capabilities and pretilt angle of the thin plastic substrates by in-situ photoalignment method were better than that of the glass substrate by general photoalignment. Also, the LC pretilt angle increased with increasing healing temperature and exposure time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.502-505
• /
• 2003

We synthesized high thermal photoalignment material with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the photopolymer surface can be obtained. However, the low pretilt angles were obtained below $1^{\circ}$. The Voltage-transmittance (V-T) curve without backflow bounce in the photoaligned TN cell with UV exposure was observed. The response time of photoaligned TN cell was measured about 24 ms.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1169-1172
• /
• 2004

Polyimides are blended with photoreactive polymers in order to improve the thermal stability of molecular orientation of photoreactive groups induced by polarized UV irradiation. The polyimide/photopolymer blends can be applied for the photo-induced liquid crystal alignment layers. However, the polyimides are also decomposed by UV irradiation and this may have the negative effect on the orientation of liquid crystals. In order to elucidate the influence of polyimide on the molecular orientation of liquid crystal, non-photoreactive naphthalenic polyimide (1,4,5,8-naphthalene tetracarboxylic dianhydride} was selected for the blend alignment layers. We prepared the blends of photo-reactive coumarin polymers and naphthalenic polyimide, and investigated the orientation of liquid crystals. Thermal stability of the orientation of liquid crystals was enhanced due to the thermally stable polyimide. However, there was no other side-effect of polyimide on the orientation of liquid crystals and this might be attributed to the non-photo-reactivity of naphtahlenic polyimide.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.940-941
• /
• 2009

The adsorption strength of liquid crystal molecules on the polymer surface was compared measuring temperature dependence of retardation above Nematic-Isotoropic transition temperature ($T_{NI}$). The relationship between surface order parameter and adsorption strength on the polymer surface was discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.136-139
• /
• 2003

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of a-C:H thin film as working gas at 30W rf bias condition. A high pretilt angle of about $5^{\circ}$ by ion beam(IB) exposure on the a-C:H thin film surface was measured. A good LC alignment by the IB alignment method on the a-C:H thin film surface was observed at annealing temperature of $250^{\circ}C$, and the alignment defect of the NLC was observed above annealing temperature of $300^{\circ}C$. Consequently, the high LC pretilt angle and the good thermal stability of LC alignment by the IB alignment method on the a-C:H thin film surface as working gas at 30W rf bias condition can be achieved.

• Macromolecular Research
• /
• v.9 no.6
• /
• pp.303-312
• /
• 2001

The fabrication of liquid crystal display (LCD) panels involves several thermal processes such as imidization of the alignment layer (AL) and annealing of the rubbed polyimide AL. The nature of these processes on the LC alignment, especially on the pretilt angle (Θ$\_$p/) has been systematically studied, employing various types of polyimide structures. The imidization effect depends on the nature of polyimid precursors; Θ$\^$p/ increases with the degree of the imidization for the main-chain type of ALs, due to the decrease in the surface polarity, but this relation is not applicable to the alkylated ones in which the steric effect at the AL surface by the aliphatic side chains is dominant. Annealing of the rubbed polyimide AL deteriorates its rubbing-induced molecular orientation and subsequently the overlying LC alignment, resulting in the decrease in Θ$\_$p/. Especially, annealing of the LC cell affects the LC-AL interaction as well as the AL orientation and thus its effect on LC alignment depends sensitively on the nature of LC-polyimide interface; aromatic moiety in the polyimide structure gives better thermal stability of LC alignment while fluorinated polyimide ALs induce the less stable alignment.