• Journal of Pharmaceutical Investigation
• /
• 제14권4호
• /
• pp.161-169
• /
• 1984

The tests of dissolution and bioavailability of six formulas of lorazepam tablet under various binders were performed. Lorazepam can be seperated in pharmaceutical preparation and biological plasma by high performance liquid chromatograph. Dissolution process of lorazepam tablet was largely influenced by binder and the dissolution rate was increased by sodium starch glycolate and microcrystalline cellulose, the slower dissolution rate in starch. Bioavailability of lorazepam tablet got relationship with dissolution rate, because tablets containing sodium starch glycolate and microcrystalline cellulose as binder maintained higher plasma level than other binders.

• Advances in concrete construction
• /
• 제10권3호
• /
• pp.237-245
• /
• 2020

Past research efforts already established geopolymer as an environment-friendly alternative binder system for ordinary Portland cement (OPC) and recycled aggregate is also one of the promising alternative for natural aggregates. In this study, an effort was made to produce eco-friendly mortar mixes using geopolymer as binder and recycled fine aggregate (RFA) partially and study the resistance ability of these mortar mixes against the aggressive environments. To form the geopolymer binder, 70% fly ash, 30% ground granulated blast furnace slag (GGBS) and alkaline solution comprising of sodium silicate solution and 14M sodium hydroxide solution with a ratio of 1.5 were used. The ratio of alkaline liquid to binder (AL/B) was also considered as 0.4 and 0.6. In order to determine the resistance ability against aggressive environmental conditions, acid attack test, sulphate attack test and rapid chloride permeability test were conducted. Change in mass, change in compressive strength of the specimens after the immersion in acid/sulphate solution for a period of 28, 56, 90 and 120 days has been presented and discussed in this study. Results indicated that the incorporation of RFA leads to the reduction in compressive strength. Even though strength reduction was observed, eco-friendly mortar mixes containing geopolymer as binder and RFA as fine aggregate performed better when it was produced with AL/B ratio of 0.6.

• 한국전기전자재료학회논문지
• /
• 제32권3호
• /
• pp.223-228
• /
• 2019

We fabricated a printed Ag:CNT film as a liquid sensor for the detection of HNS (hazardous and noxious substances) in seawater. The paste required for printing was prepared using Ag powder, MWCNTs (multi-walled carbon nanotubes), and an organic binder. The heat treatment process for binder removal was optimized. In order to confirm that the sensor was operational, the resistance change characteristics in brine (3.5%) and methanol (99.8%) were assessed at $20^{\circ}C$. EDL (electrical double layer) formation and redox reactivity were confirmed as the most important reactions affect each electrical property of sensor in brine and methanol. From these results, it was determined that printed Ag:CNT film can be applied as a sensor to detect HNS in seawater.

• 대한화장품학회지
• /
• 제25권4호
• /
• pp.97-110
• /
• 1999

The new stick make-up product was studied by using a gel, which is a viscous complex formed with clay minerals, vitamins A and E and fluorinated liquid polymer with a 1500 molecular weight. The gel cannot be obtained with any random combination of clay minerals and the ingredients described above. It takes the sequential manufacturing method as follows to get this kind of gel. Firstly, clay minerals and liquid polymers have to be pre-mixed in order to saturate the liquid polymers with the clay minerals. Then the on-processed gel has to be finely crystallized. The clay minerals, which are the core elements for this gel, were used as a function of Binder & Buffer and liquid polymer was mixed together for the deterioration of the surface tension of each component and to form a functional film in the gel. This liquid polymer was combined with clay minerals because it is not miscible with most oils and solvents. Waxes have a function of keeping a solid status in the stick. We reduced the usage of waxes by putting clay minerals as buffer in the proportion of 0.5:1 with oil phase. Ceramide takes care of the skin when used regularly and maintains the skin's moisture. Vitamins A and E contribute to preventing skin aging by the activation of skin cells. We could get the stable viscous gel, which has about 80% oil phase using clay minerals and liquid polymer. The crystalline structures of gel were surface-chemically-analyzed using SEM and Image Analyzer and were thermodynamically analyzed using DSC. Surface tension test and softness were done by Rheometer. In the end, these characteristics were verified by consumer panel tests in Seoul, Daegeon and Pusan in Korea and Hokkaido, Osaka and Miyazaki in Japan with correlation to the climate.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 1999년도 IFSCC . ASCS 학술대회 발표 논문
• /
• pp.97-110
• /
• 1999

The new stick make-up product was studied by using a gel, which is a viscous complex formed with clay minerals, vitamins A and I and fluorinated liquid polymer with a 1500 molecular weight. The gel cannot be obtained with any random combination of clay minerals and the ingredients described above. It takes the sequential manufacturing method as follows to get this kind of gel. Firstly, clay minerals and liquid polymers have ·to be pre-mixed in order to saturate the liquid polymers with the clay minerals. Then tile on-processed gel has to be finely crystallized. The clay minerals, which are the core elements for this gel, were used as a function of Binder & Buffer and liquid polymer was mixed together for the deterioration of the surface tension of each component and to from a functional film in the gel. This liquid polymer was combined with clay minerals because it is not miscible with most oils and solvents. Waxes have a function of keeping a solid status in the stick. We reduced the usage of waxes by putting clay minerals as buffer in the proportion of 0.5 : 1 with oil phase. Ceramide takes care of the skin when used regularly and maintains the skin’s moisture. Vitamins A and I contribute to preventing skin’aging by the activation of skin cells. We could get the stable viscous gel, which has about 80% oil phase using clay minerals and liquid polymer, The crystal 1 me structures of gel were surface-chemical1y-analyzed using SEM and Image Analyzer and were thermodynamically analyzed using DSC, Surface tension test and softness were done by Rheometer. In the end, these characteristics were verified by consumer panel tests in Seoul, Baegeon and Pusan in Korea and Hokkaido, Oska and Miyazaki in Japan with correlation to the climate.

• 대한전기학회논문지
• /
• 제40권9호
• /
• pp.908-912
• /
• 1991

YBaCuO oxide superconductor-shows superconductive at Liquid Nitrogen temperature-must be preparate wire or thin film form for utility. The wiring is possible with heat treatment after appropriate mixture of polymeric binder and YBaCuO oxide superconductor has fabricated. This study, analyzed the characteristics of fabricated superconductor and extruded wire after application to each of a mixed at different rate in the superconductor and compared with an original pure sample. From the result, we knew that the binder component influences superconducting characteristics. The best condition for superconductivity occurred at a criticla temperature of 86.4K (8:2 rate) and at a critical current density of 100.27A/cmy with a binder packing ratio of about 20~25 percent.

• 한국도로학회논문집
• /
• 제19권2호
• /
• pp.127-135
• /
• 2017

PURPOSES: The objective of this study is to evaluate the effect of anti-stripping on asphalt mixtures constituting anti-stripping agents. METHODS : Based on the literature review, asphalt mixture added with anti-stripping agents was prepared, and these asphalt mixtures were evaluated for anti-stripping properties for each anti-stripping agent through various lab tests, namely, tensile strength ratio (TSR), dynamic immersion test, uniaxial compression test, and indirect tensile strength test (IDT). The liquid anti-stripping agents used in the lab test were premixed with each asphalt binder (PG 64-22, PG 76-22) before being mixed with the aggregate. RESULTS :The result of the TSR test revealed that the effect of anti-stripping was highest when hydrated lime and liquid anti-stripping agent W were added. The correlation coefficient $R^2$ between the TSR result and cohesion ratio is 0.99, which indicates that the sensitivity of the TSR to moisture damage is reliable from the mechanical point of view. The covering ratio of the asphalt binder to the liquid anti-stripping agent W was determined to be higher than that to the other liquid anti-stripping agents. CONCLUSIONS :It is considered that the improved moisture resistance of asphalt mixture as a result of the use of anti-stripping agents can reduce the incidence of various pavement damages such as portholes caused by stripping, and the performance life of the asphalt road pavement can be prolonged.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 추계 학술논문 발표대회
• /
• pp.57-60
• /
• 2007

This study is to discuss the effect of the liquid type high early strength agent considering early strength, developing strength, and economics of the concrete using admixtures. The powder type high early strength agent does not helpful because the field application is not available such as the problem of mixing process and rack of economics. To make up these subjects, the plain mixture contains the standard type AE water reducing agent, and the types of the agents are the standard type AE water reducing agent(P),liquid type high early strength agent(AD),poly carboxylate high early strength type AE water reducing agent(E1), and naphthalene + melamine high early strength type AE water reducing agent(E2). As the Contents of the agents, E1 and E2 is two types each cases, and P is one type to satisfy the target fluidity and air content, AD is three types as 0.5, 1.0,and 1.5%. In the case that AD is mixed, the fluidity is decreased, but air content is increased. For increasing strength of the early age, using OPC is more effective than FA and BS for increasing the early strength of the concrete, and if the air content is secure as plain, the effect of the developing strength can be increased because the air content is increased about 2% in the case that AD is used.

• Journal of Electrochemical Science and Technology
• /
• 제13권4호
• /
• pp.453-461
• /
• 2022

A chemically sintered and binder-free paste of TiO₂ nanoparticles (NPs) was prepared using a binary-liquid mixture of 1-octanol and CCl₄. The 1:1 (v/v) complex of CCl₄ and 1-octanol easily interacted chemically with the TiO₂ NPs and induced the formation of a highly viscous paste. The as-prepared binary-liquid paste (P_BL)-based TiO₂ film exhibited the complete removal of the binary-liquid and residuals with the subsequent low-temperature sintering (~150℃) and UV-O₃ treatment. This facilitated the fabrication of TiO₂ photoanodes for flexible dye-sensitized solar cells (f-DSSCs). For comparison purposes, pure 1-octanol-based TiO₂ paste (P_O) with moderate viscosity was prepared. The P_BL-based TiO₂ film exhibited strong adhesion and high mechanical stability with the conducting oxide coated glass and plastic substrates compared to the P_O-based film. The corresponding low-temperature sintered P_BL-based f-DSSC showed a power conversion efficiency (PCE) of 3.5%, while it was 2.0% for P_O-based f-DSSC. The P_BL-based low- and high-temperature (500℃) sintered glass-based rigid DSSCs exhibited the PCE of 6.0 and 6.3%, respectively, while this value was 7.1% for a 500℃ sintered rigid DSSC based on a commercial (or conventional) paste.

• Journal of Information Display
• /
• 제12권2호
• /
• pp.97-99
• /
• 2011

We report flexible, bistable cholesteric displays utilizing polyester (PET) substrates with printed internal black electrodes. The black electrodes consist of carbon ink dispersed in butyl carbitol using a patented roll-to-roll gravure-offset printing. A transparent conducting polymer printed on PET serves as the counter electrode. The electro-optic material is a chiral nematic mixture dispersed in a low-concentration polymer binder. The device can be switched between scattering (black) and reflective (vibrant green) states upon application of an electric pulse. The internal black electrode enhances the contrast of the display and simplifies the roll-to-roll manufacture of flexible displays.