• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1081-1088
• /
• 2000

In this paper, a compliance control strategy for robot manipulators that employs a self-adjusting stiffiness function is proposed. Based on the contact force, each entry of the diagonal stiffness matrix corresponding to a task coordinate in the operational space is adaptively adjusted during contact along the corresponding axis. The proposed method can be used for both the unconstrained and constrained motions without any switching mechanism which often causes undesirable instability and/or vibrational motion of the end-effector. The experimental results involving a two-link direct drive manipulator interacting with an unknown environment demonstrates the effectiveness of the proposed method.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.1
• /
• pp.38-44
• /
• 2006

The omnidirectional mobility of a mobile robot may lose significance in motion control, unless the isotropy characteristics of the mechanism is maintained well. This paper investigates the local and global isotropy of an omnidirectional mobile robot with three caster wheels. All possible actuations with different number and combination of rotating and steering joints are considered. First, the kinematic model based on velocity decomposition and the algebraic conditions for the local isotropy are obtained. Second, the geometric conditions for the local isotropy are derived and all isotropic configurations are fully identified. Third, the global isotropy index is examined to determine the optimal parameters in terms of actuation set, characteristic length, and steering link length.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.263-272
• /
• 2008

We implemented a real-time servo system for a manipulator based on Laser Range Finder (LRF). and established algorithms for grasping a moving cylinder. We devised a manipulator mechanism and driving hardware based on a system board equipped with Xscale Processor with real-time operating system RTAI on Linux. The manipulator motor driver is connected to the system board via CAN communication link, and LRF is connected via RS-232C. We implemented real-time software including CAN device driver, RS-232C device driver, manipulator trajectory generator, and LRF control software. A typical application experiment for grasping a cylinder with circle motion demonstrated our system's real-time performance.

• Journal of Biomedical Engineering Research
• /
• v.30 no.3
• /
• pp.205-212
• /
• 2009

This paper proposes a biomimetic hand prosthesis with tendon-driven five fingers. Each finger is composed of a distal-middle phalange, a proximal phalange and a metacarpal bone, which are connected to a link mechanism. The finger flexion is a resultant motion by pulling a wire to serve as a tendon, but the finger extension is performed by an elastic mechanism composed of a restoration spring. The designed hand prosthesis with tendon-driven five fingers has totally six degrees of freedom. But its weight is merely 400.73g. The hand can perform various hand functions such as the grasping and the hand postures. From experimental results, we show that the proposed hand prosthesis is useful to amputees as a prosthetic hand.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.306-315
• /
• 2004

A Bridge Transported Servo Manipulator (BTSM) for Advanced spent fuel Conditioning Process (ACP) has been developed to overcome the limitation of access that is a drawback of Mechanical master-slave manipulators (MSMs) for the equipment maintenance. Wire-driven mechanisms have been adopted to increase the handling capacity to weight. The main disadvantage of the wire driven mechanism is that if one link is in motion, other links can be affected because wires and links are coupled. In this paper, the relationship between pulleys and links are formiliarized to overcome this drawbacks, Derived equations are proven and analyzed through experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.175-181
• /
• 2014

A four-link mechanism consisting of torsion bars is used for opening the trunk lid in most midsize sedans. When the weight of the lid is in equilibrium with the spring force exerted by torsion bars, the lid stops opening at a pop-up height. However, the actual pop-up height has large deviations from the specified height even with the same parts in the same car model, which leads to quality issues. Automotive manufacturers have experienced this deviation problem despite much effort to resolve it. In this research, we developed a multi-body dynamics model for the analysis of pop-up deviation of a trunk lid with torsion bars, which can simulate the actual pop-up motion of the trunk lid by considering kinematic constraints of the motion and friction forces in joints. We could also determine the most important factor that governs the pop-up height by sensitivity analysis of all parts. The developed system can be used for the analysis of other trunk lid systems to control the tolerance of parts.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.