• 한국산업융합학회 논문집
• /
• 제5권4호
• /
• pp.379-384
• /
• 2002

As automotive diesel engines adopt the direct injection method for a lower level of the exhaust emission and a higher fuel efficiency, the maximum temperature of engine coolant decreases. Consequently, the total available heat source from the engine coolant decreases over 35%. However, the heating source of air-conditioning system in automobiles depends on the hot engine coolant completely, so that it is nearly impossible to control air conditioning in heating season. Therefore, the present study has been carried out to develop the air conditioning system for the high efficient heat pump type using the HFC-134a. Especially, the air conditioning system of heating has been developed at a beginning stage, when it has low heat source from small and medium sized diesel recreation vehicles. To develop a control logic system for air conditioning system which is a heat pump type with a heat recovery exchanger, its cycle characteristics has been investigated according to the opening of LEV at a bench system.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.985-993
• /
• 2015

자유피스톤 스털링 엔진(Free-piston Stirling Engine, FPSE)은 석유자원 고갈로 인한 에너지 비용 상승으로 활발하게 연구되고 있는 신재생 에너지와 폐에너지 회수를 위한 핵심 에너지 변환장치로 주목받고 있다. 기존 스털링 엔진은 두 개의 피스톤과 기구부로 구성되어 열에너지를 기계동력을 변환한다. FPSE 는 기존 스털링 엔진의 단점인 기구부를 제거하고 각각의 피스톤에 스프링을 연결하여 진동 시스템으로 구성된 엔진으로서, 올바른 엔진 설계 및 운전 제어를 위하여 정교한 동역학 성능 예측이 필수적이다. 본 논문에서는 FPSE 의 외부 부하를 고려한 동역학 성능 예측 모델을 제시하고 선형 및 비선형 해석을 통한 성능 예측 방법론을 제시하였다. 선형 해석은 고유치 해석을 통한 근궤적 선도를 이용하여 엔진의 작동점을 예측한다. 비선형 해석은 외부 부하 감쇠의 선형항과 비선형항을 고려하여 수치적분을 통해 엔진 피스톤의 진폭을 예측한다. 이러한 동역학 성능 데이터는 엔진 출력 성능 예측에 활용된다. 또한, 본 논문의 해석 모델은 대표적인 FPSE 인 RE-1000 의 실험결과 및 기존 해석 연구들과 비교/검증하여 신뢰성을 검토하였다.

• 소성∙가공
• /
• 제8권3호
• /
• pp.283-283
• /
• 1999

In the present study, the effect of microporosity on the tensile properties of as-cast AZ91D magnesium alloy was investigated through experimental observation and numerical prediction. The test specimens were fabricated by die-casting and gravity-casting. For gravity-casting, the inoculation and use of various metallic moulds were applied to obtain a wide range of microporosity. The deficiency of the interdendritic feeding of the liquid phase acted as d dominant mechanism on the formation of the micropores in the Mg-Al-alloys, rather than the evolution of hydrogen gas. Although tensile strength and elongation has a nonlinear and very intensive dependence upon microporosity, the yield strength appeared to have a linear relationship with microporosity. However, it was possible to quantitatively estimate the linear contribution of microporosity on the individual tensile property far a range of microporosity, which was below about B %. The numerical prediction suggests that the effect of microporosity on fractured strength and elongation decreased as the strain hardening exponent increased. Furthermore. the shape and distribution of micropores may play a more dominant role than local plastic deformation on the tensile behavior of AZ9lD alloy.

• 소성∙가공
• /
• 제8권3호
• /
• pp.295-295
• /
• 1999

In the present study, the corrosion behavior of AZ91D as-cast alloy was investigated form the viewpoint of the distribution aspect of precipitate ($Mg_{17}Al_{12}$) and the variation of Al concentration in the Mg-rich matrix. The dendrite arm spacing (DAS) of an as-cast specimen was measured as a function of degree which describes the distribution aspect of the precipitate, and the salt spray test was conducted for various grain-sired specimens fur 20 days. The dendrite arm spacing increased as the grain size increased to about 150㎛, but a constant value is indicated when the grain size exceeds that range. Although the relationship between the corrosion rate and grain size is of a nonlinear type, the linear trend between the corrosion rate and the dendrite arm spacing is maintained for the overall range of dendrite arm spacing. Since the precipitate in the as-cast alloy is discontinuously distributed, this linear relationship means that the variation of Al-solute concentration in the Mg-rich matrix has a more potent effect than the protective action of the precipitate on the corrosion behavior of an as-cast alloy.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.135-146
• /
• 2013

This paper presents a feedforward control algorithm for the EGR and VGT systems of passenger car diesel engines. The air-to-fuel ratio and boost pressure are selected as control indicators and the positions of EGR valve and VGT vane are used as control inputs of the EGR and VGT controller. In order to compensate the non-linearity and coupled dynamics of the EGR and VGT systems, we have proposed a non-linear model-based feedforward control algorithm which is obtained from static model inversion approach. It is observed that the average modeling errors of the feedforward algorithm is about 2% using stationary engine experiment data of 225 operating conditions. Using a feedback controller including proportional-integral, the modeling error is compensated. Furthermore, it is validated that the proposed feedforward algorithm generates physically acceptable trajectories of the actuator and successfully tracks the desired values through engine experiments.

• 한국추진공학회지
• /
• 제11권5호
• /
• pp.37-50
• /
• 2007

본 연구에서는 액체 추진제 로켓엔진의 연소기에 주로 사용되는 액체 동축 스월형 분사기의 분무특성을 예측할 수 있는 모델을 개발하여 분무 연소장을 계산하기위하여 개발된 KIVA의 환경에 적합하도록 유도하였다. 액막의 분열에는 선형 안정성 이론을 도입하여 장파와 단파의 영역을 모두 고려할 수 있는 모델을 개발하였고 점성이 고려된 수력학적 해석을 통해 초기의 액막 두께와 분무각 및 분사 속도를 예측하였다. 또한 개발된 분무 모델에 대한 난류 모델의 적합성을 평가하여 RNC $k-{\varepsilon}$ 모델이 적합함을 알았다. 이러한 모델의 평가를 바탕으로 액체로켓엔진에 장착되는 분사기에서 생산되는 분무의 특성을 실험 결과와 비교하였고, 분열 길이, 분무각 및 SMD가 정성적, 정량적으로 잘 일치하는 것을 알 수 있었다.

• 한국컴퓨터정보학회:학술대회논문집
• /
• 한국컴퓨터정보학회 2019년도 제59차 동계학술대회논문집 27권1호
• /
• pp.341-342
• /
• 2019

본 논문에서는 게임 엔진에서의 감마(Gamma)와 선형(Linear) 렌더링 방식의 차이에 대해 연구하였다. 선형 렌더링 방식은 정확한 이미지 연산 및 조명 연산을 표현할 수 있기 때문에 이미 많은 실시간 게임 엔진에서 사용되고 있는 렌더링 방식이지만, 모바일 기기는 그 하드웨어적 제한으로 인해 특정 하드웨어에서는 선형 렌더링을 적용할 수 없기 때문에 그 기능을 직접 구현하거나 정확하지 않은 실시간 렌더링 결과물을 감수하여야 한다. 그래서 본 논문에서는 게임 엔진에서 사용되는 감마 렌더링 방식과 선형 렌더링 방식에 대한 개념과 그 차이를 연구하고, 이것을 효율적으로 이용할 수 있는 방법에 대해서 연구한다.

• International Journal of Railway
• /
• 제9권2호
• /
• pp.41-45
• /
• 2016

In this paper, a study on the efficiency improvement of the magnetic levitation train using the LIM (Linear Induction Motor) was presented. The maglev train has the advantage of being environmentally friendly since much less noise and dust is produced. However, due to structural limitation, compared to a rotating induction motor, linear induction motor, the main propulsion engine of the maglev train has a relatively greater air gap and hence has the lower operation efficiency. In this paper, the relationship between the operating condition of the train and the slip frequency has been investigated to find out the optimum slip frequency that might improve the efficiency of the magnetic levitation train with linear induction motor. The slip frequency is variable during the operation by this relationship only within a range that does not affect the levitation system of the train. After that, the comparison of the efficiency between the conventional control method with the slip frequency fixed at 13.5[Hz] and the proposed method with the slip frequency variable from 9.5[Hz] to 6.5[Hz] has been conducted by simulation using Simplorer. Experiments of 19.5[ton] magnetic levitation trains owned by Korea Institute of Machinery and Materials were carried out to verify the simulation results.

• Tribology and Lubricants
• /
• 제28권2호
• /
• pp.47-55
• /
• 2012

Generally, to product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive package liquid and a polymer liquid as viscosity index improver in order to improve the lubricating property of base oil. That is, engine oil is the mixture of more than two fluids. Specially, a polymeric type liquid cannot be seen as the linear viscosity like Newtonian fluids. In this research, by using the governing equation describing non-Newtonian hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics, it will be compared the bearing performance between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed hydrodynamic journal bearing. Further, it is to be found the way estimating the performance of the blended multi-grade engine lubricant in a journal bearing in advance before blending by using the physical properties of mineral base oil, fundamental additive liquid and polymer liquid of viscosity index improver. So, it can be reduced the number of trial and error to get the wanted lubricant by selecting the proper volume fraction of each liquid to satisfy the expected performance and estimating in advance the performance of various multi-grade oils before blending. Therefore, it can be shorten the developing time and saved the developing cost.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.172-179
• /
• 1998

Valve lifter namely tappet is supported by lifter hole which is located upper side of camshaft in cylinder block transforms rotatic mvement of camshaft into linear movement and helps to open and shut the en-gine valve as an engine parts. The face of valve lifter which is continuously contacting with camshaft brings about abnormal wears such as unfair wear and early wear because it is severely loaded in the valve train system. These wears act as a defect like over-clearance and cause imperfect combustion of fuel during the valve lifting in the combustion chamber. Consequently this imperfect combustion makes the engine out-put decrease and has cause on air pollution. To prevent these wears therefore The valve lifter cast in me-tal developed into SiC ceramics valve lifter which has an excellence in wear and impact resistance As a results the optimum process conditions like injection condition mixture ratio and debonding process could be established. After sintering fine-sinered dual microstructure in which prior ${\alpha}$-SiC matches well with new SiC(${\beta}$-SiC) produced by reaction among the ${\alpha}$-SiC carbon and silicon was obtained. Based on the study it is verified that mechanical properties of SiC valve lifter are excellent in Vickers hardness 1100-1200 bending strength (300-350 Pa) fracture toughness(1.5-1.7 Mpa$.$m1/2) Through engine dynamo test-ing SiC valve lifter and metal valve lifter are examined and compared into abnormal phenomena such as early fracture unfair and early wear. It is hoped that this research will serve as an important springboard for the future study of heavy duty diesel engine parts developed by ceramics which has a good wear resis-tance relaibility and lightability.