• Proceedings of the KSRS Conference
• /
• 1999.11a
• /
• pp.177-181
• /
• 1999

This paper presents an algorithm for building detection from aerial image using segment measure function and line relation. In the detection algorithm proposed, edge detection, linear approximation and line linking are used and then line measure function is applied to each line segment in order to improve the accuracy of linear approximation. Parallelisms, orthogonalities are applied to the extracted liner segments to extract building. The algorithm was applied to aerial image and the buildings were accurately detected.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.2
• /
• pp.95-103
• /
• 2002

This paper deals with the H$_{\infty}$ control problems for discrete-time linear systems with time-varying delays in states. The existence condition and the design method of the H$_{\infty}$ state feedback controller are given. In this paper, the H$_{\infty}$ control law is assumed to be a memoryless state feedback, and the upper-bound of time-varying delay and S-procedure are used. Through some changes of variables and Schur complement, the obtained sufficient condition can be rewritten as an LMI(linear matrix inequality) form in terms of all variables.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.833-840
• /
• 2022

The precision of automation equipment and motors in factories is required, and global motor market has increased significantly. However, domestic motor technology lags behind foreign technology. In this thesis, the precision stability and efficiency were compared with a linear algorithm by applying a non-linear algorithm to a PLC servo motor and an Arduino step motor in order to improve the technology of the motor. The nonlinear algorithm was able to shorten the same driving reference time because the maximum speed of the motor was faster than the linear algorithm, and it was confirmed that the precision was improved due to the low curvature.

• ETRI Journal
• /
• v.29 no.3
• /
• pp.381-389
• /
• 2007

In this paper we propose a graph-theoretic method based on linear congruence for constructing low-density parity check (LDPC) codes. In this method, we design a connection graph with three kinds of special paths to ensure that the Tanner graph of the parity check matrix mapped from the connection graph is without short cycles. The new construction method results in a class of (3, ${\rho}$)-regular quasi-cyclic LDPC codes with a girth of 12. Based on the structure of the parity check matrix, the lower bound on the minimum distance of the codes is found. The simulation studies of several proposed LDPC codes demonstrate powerful bit-error-rate performance with iterative decoding in additive white Gaussian noise channels.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.5
• /
• pp.579-587
• /
• 2014

This paper presents a variable gain amplifier (VGA) for an analog front-end (AFE) of ultrasound medical imaging. This VGA has a closed-loop topology and shows a 37-dB-linear characteristic with a single-stage amplifier. It consists of an op-amp, a non-binary-weighted capacitor array, and a gain-control block. This non-binary-weighted capacitor array reduces the required number of capacitors and the complexity of the gain-control block. The VGA has been fabricated in a 0.35-mm CMOS process. This work gives the largest gain range of 37 dB per stage, the largest P1 dB of 9.5 dBm at the 3.3-V among the recent VGA circuits available in the literature. The voltage gain is controlled in the range of [-10, 27] dB in a linear-in-dB scale with 16 steps by a 4-bit digital code. The VGA has a bandpass characteristic with a passband of [20 kHz, 8 MHz].

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.3
• /
• pp.233-237
• /
• 2005

The reduction of the ripple of driving force is especially required for the practical utilization of linear synchronous motor for rope-less elevator. In this paper, the magnetic region of the linear motor is optimized by using topology optimization techniques (density method and ON/OFF method) in order to reduce the ripple of driving force. The optimal results of both methods are compared, and useful information for the optimal design of linear motor is obtained.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.4
• /
• pp.517-524
• /
• 2012

The operation of linear oscillating system is complicated, involving system nonlinearities of both actuator and load, and variations of driving frequency in order to track the mechanical resonance. In this paper, both analytical and state-variable modeling techniques are used to investigate the influence of actuator parameters, such as back-emf/thrust force coefficient and cogging force, on the performance of linear oscillating systems. Analytical derivations are validated by simulations, and good agreements are achieved. The findings of the paper can greatly facilitate the design and evaluation processes of permanent magnet linear actuators.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.49-52
• /
• 2008

In this study, multilayer structured ultrasonic linear motor was simulated using Atila for investigating its optimum driving conditions. The ultrasonic linear motors mainly consist of an ultrasonic vibrator to generate elliptical displacement. The ultrasonic linear motor simulated in this paper was the use of the 1st longitudinal(Ll) and 4th bending vibrations (B4). Whit the increase of the number of piezoelectric actuator layers, displacement of node was increased. Maximum total displacement of node was about $3,91{\mu}m$ at the 13 layered ultrasonic motor under 5 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.93-96
• /
• 2004

An ultrasonic linear motor was composed of a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. L1-B4 ultrasonic linear motor use longitudinal and bending multi-vibration. In order to design stators which has high efficiency and driving characteristics, The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. stator vibrator of respectively width 3, 5, 7[mm] was fabricated and experimented. as results When width was 5[mm], the driving characteristics was good.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.730-733
• /
• 2004

An ultrasonic linear motor was composed af a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. $L_1-B4$ ultrasonic linear motor use longitudinal and bending multi-vibration. In order to design stators which has high efficiency and diriving characteristics. The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. stator vibrator of respectively width 3, 5, 7[mm] was fabricated an experimented. as results When width was 5[mm], the driving characteristics was good