• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.174-181
• /
• 2004

Ultra precision positioning mechanism has widely been used on semiconductor manufacturing equipments, optical spectrum analyzer and cell manipulations. Ultra precision positioning mechanism is consisted of several actuators, sensors, guides and control systems. Its efficiency depends on each performance of components. The object of this study is to design, analysis and manufacture all of the inchworm linear motor system, which is one of the equipments embodied in ultra precision positioning mechanism. Inchworm linear motor system is consisted of a controller system and an inchworm linear motor, and its driving form is similar to a motion of spanworm. A design and manufacture of inchworm linear motor, which is consisted of three PZT actuators, a rod, two columns and a guide plate, are performed. Minimizing the von-Mises stress of the hinge using Taguchi method and simulation by FEM software optimizes the structural design in a column of flexure hinge. The designed columns and guide plates are manufactured by a W-EDM and NC-milling. A controller system, which is an apparatus to drive inchworm linear motor, can easily adjust driving conditions by varying resonance frequency and input-output voltage of actuators and amplifiers. The performance of manufactured inchworm linear motor system is verified and valuated. In the future, inchworm linear motor system will be used to make a more precision positioning by reinforcing a sensor and feedback system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.133-138
• /
• 1993

This paper presents neural network based position estimation method in slippery environment as an approach to solve one of problems which are engaged in dead reckoning method. Position estimator is composed of slip detector and linear velocity estimator. Both of them are based on the fact that dynamic characteristic of mobile robot in slippery environment is different from the case without slip. To find out the dynamic relation among driving torque, angular acceleration of driving wheel and linear acceleration of mobile robot, accelerometer is used for measuring acceleration of mobile robot and neural network is used for dynamic system identifier in slippery environment.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.261-264
• /
• 1997

A single action press robot, which consists of a driving unit, rotator, up-down feed base and feed bar, is developed and applied for the press automation. The driving unit is made up with a face cam and blade cam, which have a phase angle. The feeding system consists of a double speed-up apparatus and linear motion guides, and has a fast motion characteristics. A horizontal feeding speed of the feed bar is increased twice by the double speed-up apparatus. The driving mechanism could be simplified due to the speed-up of the feeding unit.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.681-683
• /
• 2000

This paper presents to find suitable driving voltage source for moving-coil-type linear oscillatory actuator(LOA). Thus, we construct control system and proposed three type driving voltage source. This scheme demonstrated experiments. Then, we find suitable driving voltage source for LOA.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.5 no.1
• /
• pp.1-5
• /
• 2008

Pneumatic driving systems have hard non-linear characteristic and large friction force compared with driving power. Hence, it cannot be robust against parameter uncertainties, modelling error, disturbance and noise. In this study, we apply a mixed $H_2/H_{\infty}$ control to the generalized plant for a pneumatic driving apparatus system including parameter uncertainty and disturbance. In order to design the $H_2/H_{\infty}$ controller, we use the LMI technique. To evaluate control performance and robust stability of the designed controller, we compare it with a conventional controller such as PVA(Position-Velocity-Acceleration state controller) using the simulation results. As a result, it can be known that designed controller shows better robust stability than the conventional controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.291-295
• /
• 2004

New valve driving system to control for the best volumetric efficiency at each load of an internal combustion engine within one engine cycle has been developed. The system needs to reduce pumping loss that cause by throttle valve during the intake valve is opened. In this system the intake valve is driven by a linear DC electromagnetic actuator which is controlled by personal computer. The result is compared both installed and uninstalled actuator into the cylinder head. By both of experimental and numerical calculation, the responsibility of the valve driving system to the engine speed was examined

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.5
• /
• pp.470-478
• /
• 1991

In this study, a variety of characteristics were shown experimentally under mechanically unbalnced states expected in a practicl system that linear motor is used as a driving motor of magneticlly levitated transit and the design criterion of the linear motor has been proposed. Since, with slip being at 0.1, end effect was reduced a little to increase thrust about 6.14 percents in case thatsinusoidal current conducted 5[A] in short coil at each end of linear motor for compensation of it, if the ratio of sinusoidl current versus input currents is adjusted properly, it is thought that this method small be effective one. And if the gap of exit region is bigger than that of entry region, end effect will be reduced. As a result, more effective driving will be obtained.

• Journal of Power System Engineering
• /
• v.10 no.3
• /
• pp.97-103
• /
• 2006

In this study, a position trajectory tracking control algorithm is proposed for a pneumatic artificial muscle driving apparatus composed of a actuator which imitates the muscle of human, a position sensor and a control valve. The controller applied to the driving apparatus is composed of a state feedback controller and disturbance observer. The feedback controller which feeds back position, velocity and acceleration is derived from the linear model of pneumatic artificial muscle driving apparatus. The disturbance observer is designed to improve trajectory tracking performance and to reduce the effect of model discrepancy. The effectiveness of the designed controller is proved by experiments and the experimental results show that the pneumatic artificial muscle driving apparatus with the proposed control algorithm tracks given position reference inputs accurately.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.6
• /
• pp.996-1002
• /
• 2013

This study addresses the development of a full duplex robotic system for transferring flat-panel display glass. We propose to accomplish this using a bidirectional linear transfer mechanism in place of the conventional rotary transfer mechanism. The developed full duplex robot comprises a driving part that carries the glass panel laterally, vertical part that can be moved up and down by means of a ball screw and linear motion guide arrangement, and hand part that slides by the cylinder of the driving part along the guide rail with a V-guide bearing attached to the bottom of the support. In addition, an alignment part prevents the hand part from derailing and holds the hand part while the driving part moves horizontally. The full duplex robot lifts and drives a glass panel directly while transferring it to the buffer and does not require rotational motion. Therefore, both transferring and stacking are realized with a single device. This device can be used in existing industrial facilities as an alternative to existing industrial robots in current as well as future process lines. The proposed full duplex robot is expected to save considerable amounts of time and space, and increase product throughput.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.39-47
• /
• 1997

The focus of this research is to set up and describe the mathematical derivation of an automobile power-assisted rack and pinion steering system dynamics. The mathematical model of the power steering system dynamics with a 5 DOF linear vehicle model will be used in the computer simulation and evaluated comparing with the experimental results. This model is flexible to accommodate different vehicles through simple parameter changes. The developed mathematical model will attempt to provide enhanced driver realism to a Systems Technology, Inc. driving SIMulator(STISIM).