• 제목/요약/키워드: Line array

검색결과 645건 처리시간 0.024초

E-면으로 직접 결합된 마이크로스트립 어레이 안테나 (Mecrostrip Array Antenna Directly Coupled to E-Plane)

  • 김태형;홍재표;박진택;조영기;손현
    • 전자공학회논문지A
    • /
    • 제28A권1호
    • /
    • pp.23-29
    • /
    • 1991
  • In order to improve the radiation characteristics of the microstrip antenna, microstrip array antenna consisting of one center patch fed by a coaxial probe and several patches directly coupled to the E-plane by microstrip line is analyzed. The equivalent circuit of the array antenna is represented by the conventional transmission line and the various parameters, such as the mdicrostrip line length, the patch length and the feed point location are calculated to improve the radiation pattern for 5-patch array antenna which has the equal patch width. The 5-patch array antenna with the radiation pattern which has low sidelobe level and narrow beam width is fabricated and then the measured results are compared with the computed values and the results of the single patch microstrip antenna too.

  • PDF

용량성 결합 마이크로스트립 배열 안테나에 대한 연구 (A Study on a Capacitively Coupled Microstrip Array Antenna)

  • 이종익;여준호;백운석
    • 한국정보통신학회:학술대회논문집
    • /
    • 한국정보통신학회 2015년도 추계학술대회
    • /
    • pp.63-64
    • /
    • 2015
  • 본 논문에서는 마이크로스트립 선로에 용량성으로 결합된 마이크로스트립 배열 안테나에 대해 연구하였다. 배열안테나는 접지된 유전체 기판 상의 급전 마이크로스트립 선로 부근에 직사각형 마이크로스트립 패치를 일정 간격으로 배열한 것이다. 스트립의 폭과 길이, 스트립 간격, 스트립과 급전 선로 사이의 간격 등에 따른 안테나의 특성변화를 관찰하였다. 파라미터 값들을 조절하여 중심주파수 12.5 GHz 대역용 고이득 안테나에 적합하도록 설계하였다.

  • PDF

구형 마이크로스트립 패치 배열을 이용한 진행파 안테나의 특성 해석에 관한 연구 (Analysis of traveling wave antenna using rectangular microstip patch array)

  • 안광진;윤상원;장익수
    • 전자공학회논문지A
    • /
    • 제31A권10호
    • /
    • pp.31-38
    • /
    • 1994
  • In this paper, the leaky wave readiation characteristics of a microstrip rectangular patch array is presented. The reflection and transmission characteristics are analyzed using the equivalent transmission line method. Since the leaky wave is generated from the periodic array, using the Floquet'theorem, leaky wave frequency range is predicted and confirmed by the measured reflection and transmission characterstics of the array. A 17 element microstrip patch array at X-Band is designed and tested. Teh scattering Characteristics show good agreement woth those obtained from the equivalent transmission line analysis. The radiatio characteristics at 10GHz using this method show about 3${\circ}$ shift in main lobe angle compared with measured results.

  • PDF

PowerPC 및 VxWorks를 이용한 예인선배열센서 데이터처리 플랫폼 구현에 관한 연구 (A Study on Implementation of Line Array Sensor Data Processing Platform Using PowerPC and Vxworks)

  • 임병선;김영길
    • 한국정보통신학회논문지
    • /
    • 제14권7호
    • /
    • pp.1603-1609
    • /
    • 2010
  • 본 논문은 해군 호위함급에 장착/운용되는 LAS(Line Array Sensor, 예인선배열센서)로부터 A, B, C그룹 수중음향 신호의 시리얼 데이터를 입력 받아 약속된 Protocol로 Packing하여, 고속 데이터통신과 Optic-fiber채널 장거리 전송이 가능한 SFM(Serial FPDP Module)을 통해 신호처리단으로 실시간 전송하는 센서데이터 입출력처리보드의 설계/제작 및 시험에 관해 언급한다. VME(Versa Module Eurocard) 6U크기의 한정된 보드 공간을 고려하여 Freescale사의 PowerPC계열인 MPC8265 CPU와, 기존 외장 FIFO등의 외부디바이스를 줄이고 자체 시뮬레이션 데이터생성 등을 위해 Altera사의 CycloneIII 계열 FPGA등을 사용하여 설계하고, 실시간 데이터 전송을 보장하며 각종 Device Driver, Peripheral Controller등의 Library를 제공하는 RTOS인 VxWorks를 Porting하여 소프트웨어를 개발하였다.

해저면 반사신호의 선 배열 소나 방위 오차 해석 (Estimation of bearing error of line array sonar system caused by bottom bounced path)

  • 오래근;구본성;김선효;송택렬;최지웅;손수욱;김원기;배호석
    • 한국음향학회지
    • /
    • 제37권6호
    • /
    • pp.412-421
    • /
    • 2018
  • 선 배열 소나는 배열 이득으로 인해 단일 소나에 비해 상대적으로 음압이 낮은 표적 신호일 경우에도 방위 추정이 가능한 장점이 있다. 하지만 선 배열 소나에서는 표적의 방향을 나타내는 표적 방위각과 음파의 다중경로에서 발생되는 수직각의 영향으로 방위 오차가 발생하며 이로 인해 수신 신호로부터 표적 방위를 추정하는데 어려움이 존재한다. 수중의 음파 전달 환경에 의해 발생하는 다중경로는 각 경로별로 상이한 수직각을 가지므로 이러한 특성이 선배열 소나의 방위 추정에 미치는 영향에 대해 고려할 필요가 있다. 본 논문에서는 선 배열 소나에서 다중경로의 영향으로 인해 발생하게 되는 방위 오차를 확인하며 해저면 반사 경로에서 수직각에 의한 오차를 모의하여 환경에 따른 방위 오차의 차이를 분석한다. 또한 추정된 방위각에서 거리에 따라 방위 오차를 고려한 예상 표적 방위선을 도출한다.

단열배관의 온라인 두께측정시스템 개발 (Development of Real Time On-Line Thickness Measuring System for Insulated Pipeline)

  • 장지훈;김병주;조경식;김기동
    • 연구논문집
    • /
    • 통권32호
    • /
    • pp.65-76
    • /
    • 2002
  • The intensity of x-ray or gamma-ray is attenuated according to density and thickness of the transmitted medium. In this study, by using this principle, on-line real-time radiometric system was developed using a 128 channels linear array of solid state detectors to measure wall thickness of insulated piping system. This system uses a Ir-192 as a gamma ray source and detector is composed of BGO scintillator and photodiode. Ir-192 gamma ray source and linear detector array mounted on a computer controlled robotic crawler. The Ir-192 gamma ray source is located on one side of the piping components and the detector array on the other side. The individual detectors of the detector array measure the intensity of the gamma rays after passing through the walls and the insulation of the piping component under measurement. The output of the detector array is amplified by amplifier and transmitted to the computer. This system collects and analyses the data from the detector array in real-time. The maximum measurable length of pipe is 120cm/mm. in the case of 1mm scanning interval.

  • PDF

휜의 피치 및 배열 방식에 따른 프리히터의 전열 성능에 관한 연구 (A Numerical Study on the Effect of Fin Pitch and Fin Array on the Heat Transfer Performance of a Pre-heater)

  • 유지훈;김귀순
    • 한국유체기계학회 논문집
    • /
    • 제16권6호
    • /
    • pp.40-47
    • /
    • 2013
  • In this paper, a numerical study was performed to investigate the performance characteristics of a pre-heater. The effects of fin pitch and fin array type(in-line, staggered, leaned array) were reported in terms of Colburn j-factor and Fanning friction factor f, as a function of Re. Three-dimensional numerical simulation has been performed by using flow analysis program, FLUENT 13.0. The results show that Colburn j-factor decreases with the decrease of fin pitch attached in the annular tube. But the fin pitch has little effect on f-factor. The staggered array and leaned array show improved heat transfer performance compared with in-line array, so that Colburn j-factor was increased. It also shows that the f-factor of leaned array is the highest in the studied range of Reynolds number.

Doublet 센서배열의 수중음원 위치 추정 성능 향상을 위한 시간지연 추정 기법 (Time-delay Estimation Method for Performance Enhancement of Underwater Source Localization using Doublet Array)

  • 심민섭;이지혁;이형신
    • 한국산학기술학회논문지
    • /
    • 제21권5호
    • /
    • pp.69-76
    • /
    • 2020
  • 수중에서 방사된 음원의 신호는 해수면, 해저면 반사에 의한 다중경로 시간지연(multi-path time-delay)을 포함하여 체계(system)의 센서에 수신된다. 다중경로 환경과 복잡한 해양환경의 외란(disturbance)에 의해 수신된 신호간 상관성(coherence)이 저하된다. 따라서, 신호간 시간지연값을 이용하여 수중음원의 위치를 추정하는 체계는 추정성능의 저하가 나타난다. 이러한 환경에서도 강인한 음원 위치 추정성능을 위해 선배열(uniform line array), 평면배열(rectangular array)과 같은 다양한 형태의 센서배열과 빔형성(beamforming) 기법, 비용함수(cost-function)과 같은 신호처리를 이용하여 왔다. 본 연구에서는 선배열 형태의 doublet array와 추정된 시간지연값 보정 기법을 이용하고자 한다. 3 개의 doublet array를 동일 선에 위치하였으며 각각의 doublet array에 수신된 신호간의 시간지연값을 2 단계로 추정하였다. 수신신호에 대해 상호상관(cross-correlation) 함수를 적용하여 추정된 시간지연값을 수신신호의 중심주파수(center-frequency)와 array의 개구경(aperture) 및 수중음원과의 기하학적 관계에 따라 보정하여 최종의 시간 지연값을 얻었으며 이로부터 음원의 거리와 방위를 추정하였다. 제안한 기법의 타당성을 확인하기 위해, Monte-Carlo method를 이용하여 시뮬레이션하였다.

출력을 고려한 태양전지 어레이 최적 배치에 관한 연구 (A Study on the Photovoltaic Array Optimal Arrangement Considering Power Output)

  • 최홍규;최대원;유해출;최신권;김용규
    • 조명전기설비학회논문지
    • /
    • 제23권12호
    • /
    • pp.96-105
    • /
    • 2009
  • 태양광발전소 두 곳을 샘플링하여 출력저하의 요인 중 우리나라 실정에 맞지 않는 입사각에 따른 태양전지 어레이 간의 음영에 의한 출력저하를 비교 분석하여 설비용량, 설비사양, 부지면적의 변화 없이 태양전지 어레이의 재배치를 통해 최대 출력을 낼 수 있는 태양전지 어레이의 최적 간격을 산정한다. 태양전지 어레이 1열 재배치 시에는 약 1.2[%], 2열 재배치 시에는 약 2.8[%], 3열 재배치 시에는 약 5.0[%]의 출력이 향상되었다. 또한 1열 재배치 시에는 태양전지 어레이 당 0.39[m], 2열 재배치 시에는 태양전지 어레이 당 0.82[m], 3열 재배치 시에는 태양전지 어레이 당 1.29[m]의 간격 이득을 얻었다. 태양전지 어레이 간격에 이득이 생기면서 음영의 영향을 받게 되는 시간이 점점 늦춰지게 되고 결국 출력의 향상이 나타나는 결과를 보였다.

선형 마이크로폰 어레이를 이용한 이동 차량의 음장 가시화 (Noise Visualization of Moving Vehicles Using Microphone Line Array)

  • 김시문;권휴상;박순홍;김양한
    • 한국소음진동공학회:학술대회논문집
    • /
    • 한국소음진동공학회 1996년도 춘계학술대회논문집; 부산수산대학교, 10 May 1996
    • /
    • pp.291-297
    • /
    • 1996
  • To visualize sound field or to identify noise sources, we can use many methods such as intensity method, acoustic holographic method, source identification method using line array, etc. Conventionally all these methods are performed with the assumption of stationary condition in space and time. But for moving source, spatial characteristics and frequency components are changing, so we need another processing algorithm. This paper shows some experimental results - sound field by moving noise sources. In the experiment cross type microphone line array is used for sensing pressure and cars and a motorcycle are used as moving sources that are assumed to have constant speed. The processing methods are acoustic holographic method, spherical beamforming and spectrogram.

  • PDF