• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.97-105
• /
• 2017

An air-burst munition is limited in space, so there is a limit on the size of the fuze and the amount of ammunition. In order to increase a firepower to a target with limited ammunition, it is necessary to concentrate the firepower on the ground instead of the omnidirectional explosion after flying to the target. This paper explores the design and verification of a ground-detection sensor that detects the direction of the ground and determines the flight-distance of an air-burst munition using a single axis geomagnetic sensor. Prior to the design of the ground detection sensor, a geomagnetic sensor model mounted on the spinning air-burst munition is analyzed and a ground-detection algorithm by simplifying this model is designed. A high speed rotating device to simulate a rotation environment is designed and a geomagnetic sensor and a remote-recording system are fabricated to obtain geomagnetic data. The ground detection algorithm is verified by post-processing the acquired geomagnetic data. Taking miniaturization and low-power into consideration, the ground detection sensor is implemented with analog devices and the processor. The output signal of the ground detection sensor rotating at an arbitrary rotation speed of 200 Hz is connected to the LED (Light Emitting Diode) in the high speed rotating device and the ground detection sensor is verified using a high-speed camera.

• The Journal of the Korea Contents Association
• /
• v.13 no.2
• /
• pp.314-321
• /
• 2013

Photodynamic therapy(PDT) has been recommended as an alternative therapy for various diseases including microbial infection. The aim of the present study is to evaluate the antimicrobial effect of PDT using a photofrin and home made 630 nm Light emitting diode(LED) against Staphylococci. To examine the antimicrobial effect of photofrin-mediated PDT against Staphylococcus aureus and Staphylococcus epidermidis colony forming units(CFU) quantification, and bacterial viability using flow cytometry were formed. The CFU quantification results of S. aureus and S. epidermidis were 1 cfu/ml and 16 cfu/ml of average, respectively, after PDT application with photofrin of $50{\mu}g/m{\ell}$ and 630 nm LED and energy density of $18J/cm^2$. In addition, S. aureus and S. epidermidis isolates yielded forward-scatter (FSC) and fluorescence intensity (FI) differences on flow cytometry (FCM) after PDT. S. aureus and S. epidermidis cell size(FSC) increased 8.96% and 5.55% respectively, after PDT. Also the numbers of dead cell of S. aureus and S. epidermidis were a 39% and 61% incerased. These results suggest that photofrin-mediated PDT can be an effective alternative treatment for antibacterial therapy.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.1
• /
• pp.17-22
• /
• 1999

Since the use of porous silicon for microsensors and microactuators is in the euly stage of study, only several application devices, such as light-emitting diodes and chemical sensors have so far been demonstrated. In this paper we present an overview of the present status of porous silicon sensors and actuators research with special emphasis on the applications of chemical sensors and optical devices. The capacitive type porous silicon humidity sensors had a nonlinear capacitance-humidity characteristic and a good sensitivity at higher humidity above $40\%RH$. The porous silicon $n^+-p-n^+$ device showed a sharp increase in current when exposed to an ethanol vapor. The $p^+-PSi-n^+$ diode fabricated on porous silicon diaphragm exhibited an optical switching characteristic, opening up its utility as an optical sensor or switch. The photoluminescence (PL) spectrum, taken from porous silicon under 365 nm excitation, had a broad emission, peaked at -610 nm. The electroluminescence(EL) from ITO/PSi/In LED had a broader spectrum with a blue shifted peak at around 535nm than that of the PL.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.125-125
• /
• 2010

극성 [0001] 방향으로 성장된 질화물 기반의 LED (light emitting diode) 는 분극현상에 의해 발생하는 강한 내부 전기장의 영향을 받게 된다. 이러한 내부 전기장은 양자우물 내의 전자와 정공의 공간적 분리를 야기하고 quantum confined Stark effect (QCSE)에 의한 발광 파장의 적색 편이가 발생하며 양자효율의 저하를 가져오게 된다. 이러한 문제를 해결하기 위해 InGaN/GaN이나 AlGaN/GaN 양자 우물구조를 GaN의 m-plane (1$\bar{1}$00) 이나 a-plane (11$\bar{2}$0) 등 비극성면 위에 성장하려는 시도를 하고 있다. 그러나 비극성 면의 비등방성 (anisotropy) 으로 인하여 결정성이 높은 비극성 GaN을 성장하는 데에는 많은 어려움이 있다. GaN 층의 표면을 평탄화하고 결정성을 향상시키기 위해서 저온 GaN 또는 AlN 버퍼층을 성장하는 2단계 방법이나 고온 버퍼층을 이용하여 성장하는 연구들이 많이 진행되고 있다. 본 연구에서는 고온 GaN 버퍼층을 이용하여 기존의 2단계 성장과정을 단순화한 비극성 a-plane GaN을 r-plane 사파이어 기판위에 유기금속 화학증착법 (MOCVD)으로 성장하였다. 사파이어 기판위에 AlN 층을 형성하기 위한 nitridation 과정 후 1030 도에서 두께 45 ~ 800 nm의 고온 GaN 버퍼층을 성장하고 총 박막 두께가 2.7 ~ 3 um 가 되도록 a-plane GaN을 성장하여 표면 양상의 변화와 결정성을 확인하였다. 또한 a-plane GaN 박막 성장 시에 성장 압력을 100 ~ 300 torr 로 조절하며 박막 성장의 변화 양상을 관찰하였다. 고온 GaN 버퍼층 성장 두께가 감소함에 따라 결정성은 증가하였으나 표면의 삼각형 형태의 pit 밀도가 증가함을 확인하였다. 또한 성장 압력이 감소함에 따라 표면 pit은 감소하였으나 결정성도 감소하는 것을 확인하였다. 성장 압력과 버퍼층 성장 두께를 조절하여 표면에 삼각형 형태의 pit이 존재하지 않는 RMS roughness 0.99 nm, 관통전위밀도 $1.78\;{\times}\;10^{10}/cm^2$, XRD 반가폭이 [0001], [1$\bar{1}$00] 방향으로 각 798, 1909 arcsec 인 a-plane GaN을 성장하였다. 이 연구를 통해 고온 GaN 버퍼 성장방법을 이용하여 간소화된 공정으로 LED 소자 제작에 사용할 수 있는 결정성 높은 a-plane GaN을 성장할 수 있는 가능성을 확인하였다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.41 no.4
• /
• pp.325-331
• /
• 2015

Skin is exposed to sunlight or artificial indoor light on a daily. The reached solar light on the earth surface consist of 50% visible light and 45% infrared (IR) except for ultra violet (UV). The negative effects of UV including UVB and UVA have been steadily investigated within the last decades. However, little is known about the effects of visible or IR light. In this study, we irradiated human dermal fibroblasts using light emitting diode (LED) to investigate the optimal parameter for enhancing cell growth and collagen synthesis. We found that red of 630 nm and green of 520 nm enhance the cell proliferation, but irradiation with purple and blue light exerts toxic effects. To examine the response of irradiation time and light intensity on the fibroblasts, cells were exposed to red or green light with intensities from 0.05 to $0.75mW/cm^2$. Procollagen secretion was increased of 1.4 fold by 10 min irradiation, while 30 min treatment decreased the collagen synthesis of dermal fibroblasts. Treatment with red of $0.3mW/cm^2$ and green of 0.15 and $0.3mW/cm^2$ resulted in enhancement of collagen mRNA. Lastly, we investigated the combinatorial effect of red and green light on dermal fibroblasts. The sequential irradiation of red and green light is an efficient way for the purpose of the increase in the number of fibroblasts than single light treatment. On the other hand, the exposure of red light alone was more effective method for enhancing of collagen secretion. Our study showed that specific light parameters accelerated cell proliferation, gene expression and collagen secretion on human dermal fibroblasts. In conclusion, we demonstrate that light exposure with specific parameter has beneficial effects on the function of dermal fibroblasts, and suggests the possibility of its cosmetically and clinical application.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.3
• /
• pp.214-220
• /
• 2014

The aim of this study is to optimize the efficiency of a photobiorector on the growth rate of Chlorella vulgaris (C. vulgaris) by varying distance of optical panel (OP). The round shaped C. vulgaris (FC-16) having the size of $3-8{\mu}m$ is employed in this study. The cells of C. vulgaris are cultured in the Jaworski's Medium with deionized water at $22^{\circ}C$ for 15 days. The OP is placed at four different distances i.e., at 225 mm distance (Run 1), 150 mm distance (Run 2), 112.5 mm distance (Run 3) and 90 mm distance (Run 4) having a LED (Light Emitting Diode) source. The diffuse rate is achieved to 86%, 90%, 92% and 94% for Run 1, Run 2 Run 3 and Run 4, respectively. A narrower distance of OP caused to effectively to increase the efficiency of diffuse light rate. For mass cultivation of this biomass, medium is changed according to distance of OP after attaining a maximum biomass concentration; Run 1 in 8 days, Run 2 in 6 days, Run 3 in 4 days and Run 4 in 3 days. In addition, the amount of maximum biomass rate for Run 4 was reached 3 times higher than that of Run1. However, growth rate, chlorophyll per cell, cell volume and doubling time are found to be Run 3 and Run 4 higher than that of Run 1 and Run 2 samples. However, Run 3 and Run 4 are having a slight difference in all these measurements. These findings suggest that in terms of economic consideration and efficiency towards simultaneous mass cultivation of biomass, Run 3 was found to be more effective than other samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.299-299
• /
• 2007

후막형 무기 EL (electro-luminescence) 소자는 제조공정이 간단하고, 얇고, 가볍고, 유연한 동의 많은 장점들 때문에 휴대폰의 키패드 (key-pad) 및 광고용 back-light용으로 사용되고 있다. 이 무기 EL 소자는 비교적 손쉬운 스크린 프린팅 (screen-printing) 법으로 대면적을 제작할 수 있지만, LED (light emitting diode) 등과 비교하여 밝기가 낮아서 그 응용 분야가 제한되고 있다. EL 소자의 형광층은 전면 전극과 후면 전극 사이에 위치한다. EL은 이 형광층에 고 전기장이 걸릴 때, 전기장에 의해 가속된 전자가 형광층 내부에 첨가된 발광 중심의 전자를 여기시키고, 여기된 전자가 다시 바닥상태로 완화될 때 빛이 방출되는 현상이다. 즉, EL 소자는 이러한 전자 발광 현상을 이용한 소자로서, 전압 인가 시 발광 면 전체가 균일하게 발팡하는 평면 광원이다. 이러한 EL 소자에서 휘도의 증가는 후면 전극과 형광층 사이에 삽입되는 유전체 층의 특성과 밀접한 연관성이 있다. 본 연구에서는 고휘도 무기 EL 소자를 제작하기 위하여 이 유전체 층의 특성과 소자의 성능 사이의 관계를 알아보고자 하였다. 유전체 층에 사용하기 위해서 $BaTiO_3$-PVDF (polyvinylidene fluoride)의 복합체 필름을 제조하였다. 먼저 이 복합체 필름을 스크린 프린팅 (screen printing) 법으로 코팅하기 위한 페이스트 제작을 위해서, PVDF 수지를 용제에 녹였다. 그 다음, 일반 혼합기 및 삼단 롤밀 혼합기 (3-roll milling mixer) 등을 이용하여 $BaTiO_3$ 분말과 PVDF 용액을 다양한 비율로 혼합하여 페이스트를 제조하였다. ITO가 증착된 PET Film에 스크린 프린팅 법을 사용하여 형광층, 유전층, 배면 전극 등을 차례로 코팅하였다. $BaTiO_3$ (BT) 분말과 복합체 필름의 XRD 분석 결과, 분말 시료와 복합체 시료 모두 페로브스카이트 구조의 BT 회절선만 관찰되었다. 복합체의 단면 SEM 관찰에서는, BT 분말의 무게비가 증가할수록 더 치밀한 구조를 보여줌을 확인하였다. 또 EL소자의 유전상수와 휘도도 BT 분말의 혼합비가 증가할수록 증가하였다. 본 연구에서 제작한 무기 EL 소자의 최대 휘도는 약 $130\;cd/m^2$ 정도로 측정되었는데, 이는 휴대폰 키패드의 back-light용 광원으로 사용하기 충분하다고 판단되어진다.

• Journal of Food Hygiene and Safety
• /
• v.36 no.5
• /
• pp.447-453
• /
• 2021

In this study, the effectiveness of physical control technology, a combined light sterilization (LED, UV) and hot water treatment in reducing Aspergillus ochraceus for food production environment was investigated. In brief, 1 mL aliquot of A. ochraceus spore suspension (10^7-8 spore/mL) was inoculated onto stainless steel chips, which was then dried at 37℃, and each was subjected to different physical treatment. Treatments were performed for 0.5, 1, 2, 5, 8, and 11 hours to reduce the strains using a light-emitting diode, but no significant difference was confirmed among the treatments. However, a significant reduction was observed on the chips treated with UV-C exposure and hot water immersion. After being treated solely with 360 kJ/m² of UV-C on stainless steel chip, the fungi were significantly reduced to 1.27 log CFU/cm². Concerning the hot water treatment, the initial inoculum amount of 6.49 log CFU/cm² was entirely killed by immersion in 83℃ water for 5 minutes. Maintaining a high temperature for 5 minutes at the site is difficult. Thus, considering economic feasibility and usability, we attempted to confirm the appropriate A. ochraceus reduction conditions by combining a relatively low temperature of 60℃ and UV rays. With the combined treatments, even in lukewarm water, A. ochraceus decreased significantly through the increases in the immersion time and the amount of UV-C irradiation, and the yield was below the detection limit. Based on these results, if work tools are immersed in 60℃ lukewarm water for 3 minutes and then placed in a UV sterilization device for more than 10 minutes, the possibility of A. ochraceus cross-contamination during work is expected to be reduced.

• Korean Journal of Optics and Photonics
• /
• v.25 no.1
• /
• pp.38-43
• /
• 2014

An external cavity laser supporting two wavelengths is demonstrated by incorporating polymer waveguide Bragg reflectors and a superluminescent light-emitting diode. An oversized rib waveguide structure and Bragg gratings are designed by using the effective-index and transmission-matrix methods. Bragg gratings with different periods are inscribed on a polymer waveguide through double-exposure laser interferometry. In order to tune the cavity loss affected by the reflectivity of Bragg gratings, a Bragg reflectors with varying length is incorporated. Two-wavelength-mode lasing is achieved for the device consisting of 2-mm long, 537-nm period gratings and 2.2-mm long, 540-nm period gratings; the lasing wavelengths are 1554 nm and 1564 nm, with an output power close to 0 dBm, a 20-dB bandwidth of 0.2 nm, and a side-mode suppression ratio of 45 dB.

• Journal of Adhesion and Interface
• /
• v.17 no.3
• /
• pp.110-116
• /
• 2016

A decrease in the retro-reflectivity of glass-bead-covered road paint because of a rainwater film significantly reduces the visibility of drivers at night, and has been considered as a critical cause of traffic accidents. For enhanced visibility, the microencapsulation of hydrophobically modified $SrAl_2O_4:Eu^{2+}$,$Dy^{3+}$ phosphorescent phosphor was carried out via suspension polymerization of methyl methacrylate (MMA). The effects of surface modification agent and radical initiator types, loading amount of phosphorescent phosphor, and microcapsule size on the phosphor content ($W_{TGA}$) in the luminous poly(methyl methacrylate) (PMMA) microcapsules were investigated by thermogravimetric analyses (TGA). It was found that the $W_{TGA}$ value was ranged from 7 wt% to 81 wt%, which suggests suspension polymerization is suitable for the preparation of luminous microcapsules with a wide range of phosphor content. At a lower loading amount of phosphor, the $W_{TGA}$ value obviously increased as the microcapsule size decreased; however, the $W_{TGA}$ values with a higher loading amount of phosphor were less affected by the microcapsule size. The luminous microcapsules with the size range of $425{\sim}710{\mu}m$ were collected and tested as a luminous road lanes. It was found that luminance intensities of the microcapsule-coated plates remained higher than $300mcd/m^2$ for up to 100 s in darkness after 20 min of light emitting diode lamp irradiation. The results suggest that the luminous microcapsules can be a candidate for the replacement of glass beads for enhanced visibility of drivers.