• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.51-55
• /
• 2003

Recently the requirements for light weight and high performance of the automobile have increased. Especially, the plastic fuel tube makers have made their efforts to dove]op the various plastic fuel tube module with not only dimensional accuracy but also cost competitiveness. The experiment is performed to investigate spring backs for PA12 plastic fuel tubes in case of compound bending. In the experiment, steam bending process is adopted as bending method. In this study, the results we obtained are used to design the bending fixtures and the compound bending system.

• Structural Engineering and Mechanics
• /
• v.51 no.6
• /
• pp.1017-1036
• /
• 2014

Steel tubes have an efficient shape with large second moment of inertia relative to their light weight. One of the main problems of these members is their low buckling resistance caused from having thin walls. In this study, steel foams with high strength over weight ratio is used to fill the steel tube to beneficially modify the response of steel tubes. The linear eigenvalue and plastic collapse FE analysis is done on steel foam filled tube under pure compression and three point bending simulation. It is shown that steel foam improves the maximum strength and the ability of energy absorption of the steel tubes significantly. Different configurations with different volume of steel foam and composite behavior is investigated. It is demonstrated that there are some optimum configurations with more efficient behavior. If composite action between steel foam and steel increases, the strength of the element will improve, in a way that, the failure mode change from local buckling to yielding.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.8
• /
• pp.959-965
• /
• 1988

Zinc diffusion characteristics and its applicabilities have been studied using an open-tube system. Thermal decomposition of arsenide(As) at gallium arsenide(GaAs) wafer surface was well inhibited by using Ga: poly-GaAs: Zn compositon as a diffusion source. Junction depth was obtained as 4.6x10**7\ulcorner exp)-1.25/kT) where activation energy of diffusion was 1.25eV. From Boltzmann-matano analysis, it could be identified that concentration dependencies of Zn diffusivity well consisted with those of kick-out model. The ideality factor of p+-n junction formed by Zn diffusion was about 1.6 and infrared light intensity was linearly varied in the range of sixty folds. It is concluded frodm these results that Zn diffuses according to kick-out model, and open-tube method is applicable to compound semiconductor devices.

• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.12-21
• /
• 2010

Swirling flows are found in very wide range of applications, for examples, cyclone separators, spraying machines, heat exchangers and jet pumps, ect. Relatively, little work has been done on the swirl flow using flow visualization techniques. This study deals with many visualization techniques to study on swirling flow. These techniques are related to oil films methods, smoke, dye liquids, liquid crystal, stroboscope light, smoke wire, white light, naphthalene sublimation, LDV(lase doppler Velocimetry) and PIV(particle image velocimetry). The present work has handled single, annular, carved tube, swirl expansion and swirl wake using several visualization methods in the vertical and horizontal circular tube.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.217-222
• /
• 2001

The best method to evaluate crashworthiness of a trainset as a whole is to analyse one dimensional dynamic model composed of nonlinear dampers, springs and bars, and masses. In this study, crashworthiness of KHST was evaluated by analysing a nonlinear spring/bar-damper-mass model. The numerical results show that the KHST can easily absorb kinetic energy at lower impact force and acceleration in a heavy collision, when compared with KTX. Also, the KHST can be protected from any damage in its carbody and components except the prepared energy absorbing tube in a light collision, like a traint-to-train accident at speed under 8 kph. However, the KTX can be much damaged in the a light collision because there is no energy absorbing tube.

• 연구논문집
• /
• s.32
• /
• pp.103-111
• /
• 2002

In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear spring/bar-damper-mass model of 1-dimensional collision dynamics. The numerical results show that KHST can easily absorb kinetic energy at lower impact force and acceleration in heavy collisions, when compared with KTX. Also, in a Light collision like a traint-to-train accident at lower speed under 8 kph, the carbody and components of KHST can be protected without any damage except the energy absorbing tube to be replaced easily. However, KTX may be much damaged in the light collision because there is no energy absorbing tube. In conclusion, the crashworthy performance of KHST has been much improved than that of KTX, although there are something to be improved for a better crashworthy performance

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.47-53
• /
• 2002

In this study, the crashworthiness of KHST is evaluated by analysing a nonlinear spring/bar-damper-mass model using 1 dimensional collision dynamics. The numerical results show that KHST can easily absorb kinetic energy at lower impact force and acceleration in heavy collisions, when compared with KTX. Also, in a light collision like a traint-to-train accident at speed under 8 kph, the carbody and components of KHST can be protected without any damage except a energy absorbing tube to be replaced easily. However, KTX may be much damaged in the light collision because there is no energy absorbing tube. In conclusion, the crashworthy performance of KHST has been much improved than that of KTX, although there remains something to be improved for a better performance.

• Journal of Environmental Health Sciences
• /
• v.30 no.5 s.81
• /
• pp.358-365
• /
• 2004

The photocatalytic oxidation of Rhodamine B(RhB) was studied using photocatalytic reactor filled with module of quartz tube. Module of quartz tube consisted of small quartz tube (inner diameter, 1.5 mm; outer diameter, 3 mm) bundle coated with powder $TiO_2$ and uncoated large quartz tube (inner diameter, 20 mm; outer diameter, 22 mm). Two 30 W germicidal lamp was used as the light source and the reactor volume was 0.5 l. The effects of parameters such as the coating materials and numbers, initial concentration, $H_{2}O_2$ dose and metal deposition (Ag, Pt and Fe) and simultaneous application of $H_{2}O_2$ and metal deposition. The results showed that the initial reaction constant of quartz module coated with powder $TiO_2$ was higher 1.4 time than that of the $TiO_2$ sol and optimum coating number is twice. In order to increase reaction rate, simultaneous application of photocatalytic and photo-fenton reaction using Fe coating and dose $H_{2}O_2$ dose increased reaction rate largely.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1083-1086
• /
• 2005

Light scattering measurement system that can evaluate light scattering characteristic from defects on silicon wafer surface has been developed. The system uses $Ar^+$ laser as an illumination source, and a highly sensitive photomultiplier tube (PMT) for detecting scattered light from defects. Unlike with conventional measurement system, our system has ability to measure scattered light pattern from wide range of scattering angles with changeable incidence condition. It is shown that our developed system is effective to discriminate the types and sizes of defects from basic experimental results using a microscatch and a PSL sphere.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.2
• /
• pp.19-26
• /
• 2015

This paper presents design, fabrication, and performance evaluation of a high voltage power supply for Carbon Nano Tube-based planar light sources. The proposed power supply employs an LLC resonant half-bridge converter and a sixfold voltage-multiplying rectifier. Steady-state characteristics of the voltage-multiplying rectifier are analyzed and used to derive the input-to-output voltage conversion ratio of the power supply. The input-to-output frequency response characteristics of the LLC tank circuit are analyzed and utilized in designing a proto-type power supply which produces a 15 KV output using a 400 V input source. The high-voltage transformer is fabricated using a sectional bobbin structure with an epoxy impregnation, in order to provide sufficient insulation for high voltage operations. The performance of the proposed power supply is confirmed with stable and reliable operations at the 15 KV output from no load to nominal load conditions. The proposed power supply is well suited as an electric ballast required stable operations of Carbon Nano Tube-based planar light sources.