• Tribology and Lubricants
• /
• 제39권5호
• /
• pp.203-211
• /
• 2023

This study experimentally investigates the effects of angular acceleration on the friction and wear performances of a gas foil thrust bearing (GFTB) using a typical GFTB with six pads. The outer radius of the bearing is 31.5 mm, the total bearing area is 2,041 mm² , and the bump foil and incline (ramp) height are both 500 ㎛. The newly developed GFTB test rig for measuring the friction torque and coefficient measures the axial load, drag torque, lift-off speed, and touch-down speed. The experiment is conducted for angular accelerations of 78.5, 314.2, and 328.3 rad/s² at axial loads of 5, 10, and 15 N, respectively. The test shows that the start-up friction coefficient increases with increasing axial load at the same angular acceleration, and the friction coefficient decreases with increasing angular acceleration under the same axial load. As the angular acceleration increases, the lift-off speed at the motor start-up increases, and the touch-down speed at the motor stop decreases. The wear distance of the GFTB for a single on/off cycle increases with increasing axial load at the same angular acceleration and decreases nonlinearly with increasing angular acceleration under the same axial load. The test results suggest that adjusting the rotational angular acceleration helps reduce bearing friction and wear.

• 대한인간공학회지
• /
• 제28권4호
• /
• pp.161-166
• /
• 2009

Although the entrance of house has been identified as a hotspot for older adults' fall accidents, there was not any lift chair to prevent older adults' accidents. In this study, a lift chair was developed to reduce fall accidents that can occur when older adults put on or take off their shoes in the entrance. In order to develop the product, we considered two aspects. Firstly, we considered older adults' anthropometric data to determine the design specification of the product. Also we considered the environmental characteristics of space using the product. In order to overcome the limited spatial freedom and use the entrance space effectively, we took a simplified and folding type for the product.

• Advances in aircraft and spacecraft science
• /
• 제2권3호
• /
• pp.329-343
• /
• 2015

This study aimed to observe the effect of a novel concept (referred to as the flap extension) implemented on the leading edge of the flap of a three element high lift device. The high lift device, consisting of a flap, main element and slat is designed around an Airbus research profile for sufficient take off and landing performance of a large commercial aircraft. The concept is realised on the profile and numerically optimised to achieve an optimum geometry. Two different optimisation approaches based on Genetic Algorithm optimisations are used: a zero order approach which makes simplifying assumptions to achieve an optimised solution: as well as a direct approach which employs an optimisation in ANSYS DesignXplorer using RANS calculations. Both methods converge to different optimised solutions due to simplifying assumptions. The solution to the zero order optimisation showed a decreased stall angle and decreased maximum lift coefficient against angle of attack due to early stall onset at the flap. The DesignXplorer optimised solution matched that of the baseline solution very closely. The concept was seen to increase lift locally at the flap for both optimisation methods.

• 한국항공우주학회지
• /
• 제38권7호
• /
• pp.655-663
• /
• 2010

DUP(direct underside pressurization)는 위그선이 이륙하기 위하여 수면 위를 항주할때 낮은 속도에서 이륙할 수 있도록 양력을 증가시키는 역할을 한다. 이러한 DUP가 위그선의 안정성과 공기역학적인 힘에 미치는 영향에 관하여 3차원 수치해석을 수행하였다. 해석에 사용된 위그선인 "Aircat"은 동체의 중심에 프로펠러가 있고 동체하부에 공기부양실이 있으며 Lippisch형의 날개와 큰 T자형의 수평꼬리날개를 가지고 있다. 저속에서 대부분의 양력은 프로펠러에 의해 가속된 공기가 동체의 가운데 통로를 통하여 공기부양실로 들어가 정체됨으로써 발생한다. 그러나 DUP에 의해 가속된 공기는 동압의 증가로 인하여 항력을 증가 시킬 뿐만 아니라 안정성에 영향을 주게 된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.697-699
• /
• 2002

In this paper, the characteristics analysis of the eddy current sensor by using boundary element method package is presented. For the boundary element analysis. Faraday, which is the commercial package of the integrated engineering software, is used. To observe the impedance characteristic of the eddy current senor with the sensor position and lift-off, the eddy current testing analysis is performed on the ferromagnetic plate with defect. Considering the skin depth of the ferromagnetic specimen, the 800(Hz) driving source is chosen. The result shows that electro motive force is reduced as the probe moves to near the defect and the lift-off of the probe increases.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 추계 기술심포지움
• /
• pp.89-98
• /
• 2001

Pb-free wave soldering process of AC Adapter was implemented by six sigma method using Sn-Cu-Ni type solder. The solder joint appearance, microstructural change, a lift-off phenomenon and reliability were evaluated through thermal shock teal. $(Cu,Ni)_6Sn_5$-type intermetallic compound of which thickness is about 5 micron was found at solder joint between Sn-Cu-Ni solder and copper land. After applying the thermal shock test of as-soldered product up to 750 cycles, no crack was found at the solder joint and the newly developed product was superior to conventions; one in terms of productivity and reliability.

• 마이크로전자및패키징학회지
• /
• 제6권1호
• /
• pp.65-73
• /
• 1999

Lift-off 공정에 의하여 Si-tip FEA를 제조하고 그 동작 특성을 평가하였다. 게이트 및 양극 전압에 따른 방출 전류의 변화, 최대 방출 전류, 히스테리시스 현상, MOSFET형 특성, 전류 표동, 방출된 전자에 의한 형광체 발광, 그리고 소자의 파괴 메카니즘 등이 실험 결과를 토대로 하여 폭 넓게 평가, 분석되었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.28.2-28.2
• /
• 2009

Cobalt thin film was fabricated by a novel NH3-based plasma-enhanced atomic layer deposition(PE-ALD) using Co(CpAMD) precursor and $NH_3$ plasma. The PE-ALD Co thin films were produced well on both thermally grown oxide (100 nm) $SiO_2$ and Si(001) substrates. Chemical bonding states and compositions of PE-ALD Co films were analyzed by XPS and discussed in terms of resistivity and impurity level. Especially, we successfully developed PE-ALD Code position at very low growth temperature condition as low as $T_s=100^{\circ}C$, which enabled the fabrication of Co patterns through lift-off method after the deposition on PR patterned substrate without any thermal degradation.

• 비파괴검사학회지
• /
• 제27권3호
• /
• pp.255-261
• /
• 2007

By using numerical analysis methods, through transmission type pulsed eddy current (PEC) testing is modeled and PEC signal responses due to varying material conductivity, permeability, thickness, lift-off and pulse width are investigated. Results show that the peak amplitude of PEC signal gets reduced and the time to reach the peak amplitude is increased as the material conductivity, permeability, and specimen thickness increase. Also, they indicate that the pulse width needs to be shorter when evaluating the material conductivity and the plate thickness using the peak amplitude, and when the pulse width is long, the peak time is found to be more useful. Other results related to lift-off variation are reported as well.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.368-371
• /
• 2008

Cellulose based Electroactive Paper (EAPap) has been developed as a new smart material due to its advantages of piezoelectricity, large displacement, low power consumption, low cost and flexibility. EAPap can be used fur a surface acoustic wave (SAW) device using the piezoelectric property of EAPap, resulting in the cost effective and flexible SAW device. In this paper, inter digit transducer (IDT) structure using lift-off technique with a finger gap of $10{\mu}m$ was used for micro fabrication of the cellulose EAPap SAW devices. The performance of IDT patterned SAW device was characterized by a Network Analyzer. The feasibility of cellulose EAPap as a potential acoustic device was presented and explained.