• International Journal of Fluid Machinery and Systems
• /
• 제9권4호
• /
• pp.382-393
• /
• 2016

Flow over a bluff body is an attractive research field in thermal engineering. In the present study, laminar flow over a confined heated square cylinder using CuO-Water nanofluid is considered. Unsteady two-dimensional Navier-Stokes and energy equations are solved numerically using finite volume method (FVM). Recent correlations for the thermal conductivity and viscosity of nanofluids, which are function of nanoparticle volume fraction, temperature and nanoparticle diameter, have been employed. The results of numerical solution are obtained for Richardson number, nanoparticle volume fractions and nanoparticle diameters ranges of 0-1, 1-5% and 30-100 nm respectively for a fixed Reynolds number of Re = 150. At a given volume concentration, the investigations reveal that the decreasing in size of nanoparticles produces an increase in heat transfer rates from the square cylinder and a decrease in amplitude of the lift coefficient. Also, the increment of Nusselt number is more pronounced at higher concentrations and higher Richardson numbers.

• 대한기계학회논문집B
• /
• 제30권5호
• /
• pp.480-488
• /
• 2006

Numerical simulations of flow over two spheres placed in a tandem arrangement are conducted to investigate the effect of the inter-sphere spacing on the flow characteristics. The Reynolds numbers considered are 100, 250, 300 and 425, corresponding to steady axisymmetric, steady planar-symmetric, unsteady planar-symmetric, and unsteady asymmetric flows, respectively, in the case of a single sphere. For small inter-sphere spacings, the flow past two spheres is more stable than that past a single sphere. For example, with the spacing of the sphere radius, the flow is steady axisymmetric up to Re=300. However, for relatively large spacings, the flow past two spheres becomes unstable and vortex shedding takes place even at Re=250. The drag coefficient of the rear sphere decreases significantly with decreasing inter-sphere spacing due to reduction of the stagnation pressure, thus being smaller than that of the front sphere. Also, the rear sphere shows large fluctuations of the lift force as compared to the front one in the case of unsteady flow.

• Wind and Structures
• /
• 제31권1호
• /
• pp.31-41
• /
• 2020

A new type of bridge deck section consisting of four-box decks, two side decks for vehicular traffic lanes and two middle decks for railway traffic, has been experimentally investigated for determining its aerodynamic properties. The eight flutter derivatives were determined by the Iterative Least Squares (ILS) method for this new type of four-box deck model, with two windshields of 30 mm and 50 mm height respectively. Wind tunnel experiments were performed for angles of attack α = ±6°, ±4°, ±2° and 0° and Re numbers of 4.85×105 to 6.06×105 and it was found that the four-box deck with the 50 mm windshields had a better aerodynamic performance. Also, the results showed that the installation of the windshields reduced the values of the lift coefficient CL for the negative angles attack in the range of -6° to 0°, but the drag coefficient CD increased in the positive angle of attack range. However, galloping instability was not encountered for the tested reduced wind speeds, of up to 9.8. The aerodynamic force coefficients and the flutter derivatives for the four-box deck model were consistent with the results reported for the Messina triple-box bridge deck, but were different from those reported for the twin-box bridge decks.

• 한국항공운항학회지
• /
• 제21권1호
• /
• pp.45-50
• /
• 2013

In this study, lumped-vortex element method and thin airfoil theory were used to analyze aerodynamic characteristics of airfoils with relative motion that had camber lines of NACA $44{\times}{\times}$ airfoil in 2-dimensional unsteady incompressible potential flow. Velocity disturbance due to airfoil was calculated by lumped-vortex element model and force distribution on airfoil by unsteady Bernoulli's equation. Variables in relative motion were considered the period p, the amplitude of flapping $A_f$ and pitching $A_p$, and the phase difference between flapping and pitching ${\phi}_p$ and the angle of attack ${\alpha}$. Due to movement of an airfoil, dag was induced in 2-dimensional unsteady incompressible potential flow. The numerical results show that the aerodynamic characteristics of the airfoil with flapping and pitching at the same time are illustrated. Especially the mean lift coefficient became smaller, but drag coefficient became larger.

• 항공우주시스템공학회지
• /
• 제13권5호
• /
• pp.32-38
• /
• 2019

높은 후퇴각을 갖는 둥근 앞전 날개 형상은 앞전 와류에 의해 복잡한 유동 현상이 나타난다. 불안정한 방향 안정성을 갖는 무미익 플라잉윙의 제어를 위해서 플래퍼론이 사용된다. 본 연구에서는 플래퍼론이 전개된 비세장형, 둥근 앞전의 플라잉윙 형상의 전산해석을 수행하였으며 옆미끄럼각 및 플래퍼론에 대한 영향을 분석하였다. 공력계수 분석을 통해 양력과 항력계수에 대한 옆미끄럼각의 영향은 적으며 측력 및 모멘트 계수는 옆미끄럼각의 영향을 크게 받음을 알 수 있었다. 정적 안정성 분석을 통해 플래퍼론이 전개된 플라잉윙의 가로안정성과 방향안정성이 좋아졌음을 확인하였다. 또한 압력계수분포, 표면 마찰선의 관찰을 통해 앞전 와류 구조 및 거동을 분석하였다.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.221-227
• /
• 2005

Aim of this study is to investigate an aerodynamic effect of a drag-reducing device on a heavy-duty truck. The vehicle experiences two different kinds of aerodynamic forces such as drag and uplifting force (or downward force) as it is traveling straight forward at constant speed. The drag force on a vehicle may cause an increase of the rate of fuel consumption and driving instability. The rolling resistance of the vehicle may be increased as result of the negative uplifting or downward force on the vehicle. A device named roof-fairing system has been applied to examine the reduction of aerodynamic drag force on a heavy-duty truck. As for a engineering design information, the drag-reducing system should be studied theoretically and experimentally for the best efficiency of the device. Four different types of roof-fairing model were considered in this study to investigate the aerodynamic effect on a model truck. The drag and downward force generated by vehicle has been obtained from numerical calculation conducted in this study. The forces produced on four fairing models considered in this study has been compared each other to evaluate the best fairing model in terms of aerodynamic performance. The result shows that the roof-fairing mounted truck has bigger negative uplifting or downward force than that of non-mounted truck in all speed ranges, and drag force on roof-fairing mounted truck has smaller than that of non-mounted truck. The drag coefficient $(C_D)$ of the roof-fairing mounted truck (Model-3) is reduced up to $41.3\%$ than that of non-mounted trucks (Model-1). A downward force generated by a roof-fairing mounted on a truck is linearly proportional to the rolling resistance force. Therefore, the negative lifting force on a heavy-duty truck is another important factor in aerodynamic design parameter and should be considered in the design of a drag-reducing device of a tractor-trailer. According to the numerical result obtained from present study, the drag force produced by the model-3 has the smallest of all in all speed ranges and has reasonable downward force. The smaller drag force on model-3 with 2/3h in height may results of smallest thickness of boundary layer generated on the topside of the container and the lowest intensity of turbulent kinetic energy occurs at the rear side of the container.

• Wind and Structures
• /
• 제35권4호
• /
• pp.255-268
• /
• 2022

Light-weight or low-damped structures may encounter the unsteady galloping instability that occurs at low reduced wind speeds, where the classical quasi-steady assumption is invalid. Although this unsteady phenomenon has been widely studied for rectangular cross sections with one side perpendicular to the incidence flow, the effect of the mean wind angle of attack has not been paid enough attention yet. With four sectional models of different side ratios and geometric shapes, the presented research focuses on the effect of the wind angle of attack on unsteady galloping instability. In static tests, comparatively strong vortex shedding force was noticed in the middle of the range of flow incidence where the lift coefficient shows a negative slope. In aeroelastic tests with a low Scruton number, the typical unsteady galloping, which is due to an interaction with vortex-induced vibration and results in unrestricted oscillation initiating at the Kármán vortex resonance wind speed, was observed for the wind angles of attack that characterize relatively strong vortex shedding force. In contrast, for the wind angles of attack with relatively weak shedding force, an "atypical" unsteady galloping was found to occur at a reduced wind speed clearly higher than the Kármán-vortex resonance one. These observations are valid for all four wind tunnel models. One of the wind tunnel models (with a bridge deck cross section) was also tested in a turbulent flow with an intensity about 9%, showing only the atypical unsteady galloping. However, the wind angle of attack with the comparatively strong vortex shedding force remains the most unfavorable one with respect to the instability threshold in low Scruton number conditions.

• 대한토목학회논문집
• /
• 제29권5A호
• /
• pp.487-494
• /
• 2009

PSC 구조물에 사용되는 긴장재의 마찰계수는 긴장작업시 긴장력 관리를 위한 기본적인 정보가 된다. 그러나, 마찰계수는 국내외 설계기준별로 큰 차이가 있어 실무자들에게 혼란을 주어 왔다. 이 연구에서는 먼저 국내외의 관련 설계기준을 비교 분석하여 현재 통용되고 있는 마찰계수의 범위를 파악해 보았다. 그리고 긴장시의 신장량과 긴장력과 같은 실측값과 마찰계수에 대한 이론식을 조합하여 파상 및 곡률 마찰계수값을 역으로 유추할 수 있는 절차를 제안하였다. 예제로서 ILM, FCM 및 MSS 공법으로 시공된 국내 PSC 교량들을 대상으로 다양한 형상을 가진 텐던들에 제안된 절차를 적용하였다. 이를 통해 계산된 마찰계수값들을 설계기준이나 긴장시 가정되었던 값들과 비교하였으며, 이를 바탕으로 합리적인 마찰계수값의 범위에 대해 논하였다. 이 때 몇몇 교량에서는 lift-off 시험으로 고정단 긴장력을 추가적으로 측정하여 결과를 검증하는데 참조하였다. 파상 마찰계수의 경우 AASHTO 기준만큼 작은 값은 아니지만 국내 기준의 하한값에서 중간값 정도에 분포했다. 한편, 곡률 마찰계수는 국내 기준의 상한값에 가깝거나 이를 다소 상회하는 것으로 나타났다.

• Wind and Structures
• /
• 제28권2호
• /
• pp.71-87
• /
• 2019

The yaw and interference effects of blades affect aerodynamic performance of large wind turbine system significantly, thus influencing wind-induced response and stability performance of the tower-blade system. In this study, the 5MW wind turbine which was developed by Nanjing University of Aeronautics and Astronautics (NUAA) was chosen as the research object. Large eddy simulation on flow field and aerodynamics of its wind turbine system with different yaw angles($0^{\circ}$, $5^{\circ}$, $10^{\circ}$, $20^{\circ}$, $30^{\circ}$ and $45^{\circ}$) under the most unfavorable blade position was carried out. Results were compared with codes and measurement results at home and abroad, which verified validity of large eddy simulation. On this basis, effects of yaw angle on average wind pressure, fluctuating wind pressure, lift coefficient, resistance coefficient,streaming and wake characteristics on different interference zone of tower of wind turbine were analyzed. Next, the blade-cabin-tower-foundation integrated coupling model of the large wind turbine was constructed based on finite element method. Dynamic characteristics, wind-induced response and stability performance of the wind turbine structural system under different yaw angle were analyzed systematically. Research results demonstrate that with the increase of yaw angle, the maximum negative pressure and extreme negative pressure of the significant interference zone of the tower present a V-shaped variation trend, whereas the layer resistance coefficient increases gradually. By contrast, the maximum negative pressure, extreme negative pressure and layer resistance coefficient of the non-interference zone remain basically same. Effects of streaming and wake weaken gradually. When the yaw angle increases to $45^{\circ}$, aerodynamic force of the tower is close with that when there's no blade yaw and interference. As the height of significant interference zone increases, layer resistance coefficient decreases firstly and then increases under different yaw angles. Maximum means and mean square error (MSE) of radial displacement under different yaw angles all occur at circumferential $0^{\circ}$ and $180^{\circ}$ of the tower. The maximum bending moment at tower bottom is at circumferential $20^{\circ}$. When the yaw angle is $0^{\circ}$, the maximum downwind displacement responses of different blades are higher than 2.7 m. With the increase of yaw angle, MSEs of radial displacement at tower top, downwind displacement of blades, internal force at blade roots all decrease gradually, while the critical wind speed decreases firstly and then increases and finally decreases. The comprehensive analysis shows that the worst aerodynamic performance and wind-induced response of the wind turbine system are achieved when the yaw angle is $0^{\circ}$, whereas the worst stability performance and ultimate bearing capacity are achieved when the yaw angle is $45^{\circ}$.

• Journal of Multimedia Information System
• /
• 제7권2호
• /
• pp.189-196
• /
• 2020

We have developed a device for recording biological data by inserting three electrodes and a needle with an angular velocity sensor into the moth for the purpose of measuring the electromyogram of the flapping and the corresponding lift force. With this measurement, it is possible to evaluate the moth-physiological function of moths, and the amount of pesticides that insects are exposed to (currently LD50-based standards), especially the amount of chronic low-concentration exposure, can be reduced the dose. We measured and recorded 2-channel electromyography (EMG) and angular velocity corresponding to pitch angle (pitch-like angle) associated with wing flapping for 100 sweet potato hawkmoths (50 females and 50 males) with the animals suspended and constrained in air. Overall, the angular velocity and amplitude of EMG signals demonstrated high correlation, with a correlation coefficient of R = 0.792. In contrast, the results of analysis performed on the peak-to-peak (PP) EMG intervals, which correspond to the RR intervals of ECG signals, indicated a correlation between ΔF fluctuation and angular velocity of R = 0.379. Thus, the accuracy of the regression curve was relatively poor. Using a DC amplification circuit without capacitive coupling as the EMG amplification circuit, we confirmed that the baseline changes at the gear change point of wing flapping. The following formula gives the lift provided by the wing: angular velocity × thoracic weight - air resistance - (eddy resistance due to turbulence). In future studies, we plan to attach a micro radio transmitter to the moths to gather data on potential energy, kinetic energy, and displacement during free flight for analysis. Such physiological functional evaluations of moths may alleviate damage to insect health due to repeated exposure to multiple agrochemicals and may lead to significant changes in the toxicity standards, which are currently based on LD50 values.