• Journal of Applied Reliability
• /
• v.15 no.4
• /
• pp.270-275
• /
• 2015

Purpose : UHMWPE (Ultra-high-molecular-weight-polyethylene) is one of the most widely used material in knife protection clothes because of high strength, elasticity, and light weight. The purpose of this study is to develop the accelerated life test method and predict the lifetime for the knife protection fabric composed by UHMWPE. Methods : In this study, degradation characteristics of UHMWPE fibers and knife protection fabric for cut resistance were evaluated under the hydrolysis and photo-degradation conditions. It was found out that the degradation rate of retained tensile strength was more significant in the photo-degradation than hydrolysis. Therefore, the failure time was determined as the time that the retained tensile strength in photo-degradation is less than 50%. Considering an acceleration factor for irradiance and exposure time, the lifetime was predicted from the calculated failure time. Results : As a result of the accelerated life test, the $B_{10}$ lifetime of knife protection fabric composed by UHMWPE fibers is estimated as 2.8 years for a 90% statistical confidence level. Conclusion: Since the lifetime is predicted by the view-point of radiant exposure in this study, there is a possibility that the estimated lifetime may differ from the actual lifetime. However, it is considered as an useful methodology to estimate the long-term lifetime of knife protection fabrics.

• Korean Journal of Materials Research
• /
• v.20 no.6
• /
• pp.307-311
• /
• 2010

Positron annihilation lifetime spectroscopy is applied to BaSrFBr : Eu film which is used for the phosphore layer, and afterwards the reliability and self-consistency of source corrections in the positron lifetime spectroscopy is investigated using a $^{22}Na$ positron emitter covered by thin foils. The positron lifetime showed no significant change through the various proton irradiation energies. It is unusual that the measurements of the defects indicate that most of the defects were likely to have been generated by X-ray radiation. This may have resulted from the Bragg peaks of the proton characteristics. The Bragg peak does not affect the defect signals enough to distinguish the lifetimes and intensities in a material that is includes multi-grains. The lifetime ($\tau_1$) associated with positron annihilations in the Ba, Br, and Eu of the sample was about 250 ps, and due to the annihilations at F-centers or defects from the irradiated protons in sample, the lifetime ($\tau_2$) was about 500 ps.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.203-207
• /
• 2013

P-type Si wafers were dipped in HF solution. The minority carrier lifetime (lifetime) increased after HF treatment due to the hydrogen termination effect. To investigate the film passivation effect, PECVD was used to deposit $SiN_x$ on both HF-treated and untreated wafers. $SiN_x$ generally helped to improve the lifetime. A thermal process at $850^{\circ}C$ reduced the lifetime of all wafers because of the dehydrogenation at high temperature. However, the HF-treated wafers showed better lifetime than untreated wafers. PERCs both passivated and not passivated by HF treatment were fabricated on the rear side, and their characteristics were measured. The short-circuit current density and the open-circuit voltage were improved due to the effectively increased lifetime by HF treatment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.8
• /
• pp.1278-1284
• /
• 2017

As of December 2016, there are 608,828 elevators in operation in Korea and 179,790 elevators in more than 15 years. 30.4% of all elevator are aging. Improved maintenance of the elevator and proactive replacement of the parts of the elevator can extend the lifetime of the elevator and ensure safety. An unclean environment reduces the lifetime of elevator parts. If you do not clean the environment and prevent preventive parts replacement, eventually shortening the lifetime of the parts connected to the failed part or causing more damage will result in greater economic loss. Also, the risk of elevator safety accidents due to failures of elevator parts will be increased accordingly. The study of optimum replacement time of elevator parts will contribute to prevention of safety accident of elevator and prolongation of lifetime of elevator through preventive replacement of elevator parts.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.183-191
• /
• 2004

The burning characteristics of interacting droplets with internal circulation in a convective flow are numerically investigated at various Reynolds numbers. The transient combustion of 2-dimensionally arranged droplets, both the fixed droplet distances of 5 radii to 40 radii horizontally and 4 radii to 24 radii vertically, is studied. The results obtained from the present numerical analysis reveal that the transient flame configuration and retardation of droplet internal motion with the horizontal or vertical droplet spacing substantially influence lifetime of interacting droplets. At a low Reynolds number, lifetime of the two droplets with decreasing horizontal droplet spacing increases monotonically, whereas their lifetime with decreasing vertical droplet spacing decreases due to flow acceleration. This flow acceleration effect is reversed when the vertical droplet spacing is smaller than 5 radii in which decreasing flame penetration depth causes the reduction of heat transfer from flame to droplets. At a high Reynolds number, however, lifetime of the first droplet is hardly affected by either the horizontal droplet spacing or flow acceleration effect. Lifetime with decreasing vertical droplet spacing increases due to reduction of flame penetration depth. Lifetime of interacting droplets exhibits a strong dependence on Reynolds number, the horizontal droplet spacing and the vertical droplet spacing and can be con-elated well with these conditions to that of single burning droplet.

• Journal of KIISE:Information Networking
• /
• v.36 no.6
• /
• pp.505-513
• /
• 2009

In some wireless sensor networks, each wireless sensor network has its own target lifetime (desired lifetime after deployment). However, satisfying the target lifetime is not a trivial problem since the nodes in wireless sensor networks often rely on batteries as their power source. In this paper, we propose an energy efficient routing algorithm that satisfies the target-lifetime requirement of a wireless sensor network. The proposed routing algorithm not only finds energy efficient paths but also optimizes the sensing rate of each sensor node. Through simulation, we compare the performance of the proposed scheme with several other existing algorithms.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.778-783
• /
• 2003

For ac Plasma Display Panel (PDP), the lifetime should be guaranteed over 30000 hours. The lifetime is correlated with the deterioration characteristics for the weakest element in ac PDP. In this paper, in order to improve the lifetime of ac PDP, a short-term relative lifetime test method for a given element in the ac PDP is proposed. By this method, the effects of MgO thin film thickness and deposition rate on the relative lifetime of ac PDP are investigated. The relative lifetime is increased with MgO thin film thickness but it was almost saturated over 5000. The relative lifetime decreased with increase in the MgO deposition rate and increased with Xe% in the working gas of He+Ne+Xe..

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.985-988
• /
• 2004

The carrier lifetime of boron doped Cz silicon samples after light induced degradation could be improved by optimized rapid thermal processing (RTP). The important five different parameters varied in order to investigate which parameter is important for the stable lifetime after light induced degradation, $\tau_d$. The Plateau temperature and the Plateau time influenced on the lifetime after light induced degradation. Especially, the Plateau temperature showed a strong influence on the stable lifetime. The optimal plateau temperature is approximately $900^{\circ}C$ t for a plateau time of 120 s. The stable lifetime increased from $15\mu}s$ to $25.5{\mu}s$. The normalized defect concentration, $N_t^*$, decreased from $0.06{\mu}s^{-1}$ to $0.037{\mu}s^{-1}$ by RTP-process.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.7
• /
• pp.2302-2324
• /
• 2014

Cluster-based wireless sensor network (WSN) can significantly reduce the energy consumption by data aggregation and has been widely used in WSN applications. However, due to the intrinsic many-to-one traffic pattern in WSN, the network lifetime is generally deteriorated by the unbalanced energy consumption in a cluster-based WSN. Therefore, energy efficiency and network lifetime improvement are two crucial and challenging issues in cluster-based WSNs. In this paper, we propose a Non-Uniform Node Distribution (NUND) scheme to improve the energy efficiency and network lifetime in cluster-based WSNs. Specifically, we first propose an analytic model to analyze the energy consumption and the network lifetime of the cluster-based WSNs. Based on the analysis results, we propose a node distribution algorithm to maximize the network lifetime with a fixed number of sensor nodes in cluster-based WSNs. Extensive simulations demonstrate that the theoretical analysis results determined by the proposed analytic model are consistent with the simulation results, and the NUND can significantly improve the energy efficiency and network lifetime.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1715-1724
• /
• 2013

The maximum lifetime data aggregation problem is to maximize the network lifetime as minimizing the transmission energy of all deployed nodes in wireless sensor networks. In this paper, we propose a simulated annealing algorithm to solve efficiently the maximum lifetime data aggregation problem on the basis of meta-heuristic approach in wireless sensor networks. In order to make a search more efficient, we propose a novel neighborhood generating method and a repair function of the proposed algorithm. We compare the performance of the proposed algorithm with other existing algorithms through some experiments in terms of the network lifetime and algorithm computation time. Experimental results show that the proposed algorithm is efficient for the maximum lifetime data aggregation problem in wireless sensor networks.