• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.117-122
• /
• 2002

The chatter to raise grinding operating is reduce the precision and the quality. In this study, In reply to AE signal and the normal force generated in the grinding operating were measured (1) the amplitude in the mathematical model of the normal force is the form as to transform an exponential (2) the chatter growth is minus point of an exponent. (3) From the observed wheel aspect after the chatter growth, it was to investigated the concern of the chatter growth and the wheel life.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.898-901
• /
• 2000

It is known that Si3N4 ceramic insert has less hardness than Al2O3 ceramic insert. But Si3N4 ceramic insert has not only high toughness and strength but also low thermal expansion coefficient, which makes it has longer tool life under thermal stress condition. In this study, commercial Si3N4 ceramic insert and home-made SiC-Si3N4 ceramic insert which has different sintering time and chemical composition is tested under various cutting conditions. The experimental result is compared in terms of tool life and cutting force. Generally, As the cutting speed and the feed rate increased, the cutting force and the flank wear increased too. The performance of SiC-Si3N4 ceramic insert shows the possibility to be a new ceramic tool.

• 한국공작기계학회논문집
• /
• 제11권5호
• /
• pp.53-57
• /
• 2002

The chatter to raise grinding operating is reduce the precision and the quality. In this study, In reply to AE signal and the normal force generated in the grinding operating were measured (1) the amplitude in the mathematical model of the normal force is the form as to transform an exponential (2) the chatter growth is minus point of an exponent. (3) From the observed wheel aspect after the chatter growth, it was to investigated the concern of the chatter growth and the wheel life.

• 열처리공학회지
• /
• 제7권3호
• /
• pp.199-205
• /
• 1994

The fracture characteristics and tool life of ceramics and WC, CBN cutting tool when turning heat treated steel STD11($H_RC$ 60) were investigated experimentally to clarify the machinability and optimum tool materials in cutting of difficult-to-cut material with high hardness. Forthermore, the behaviors of the tool wear and failure were examined with regard to cutting force. The hardened steel wore the cutting tool edge rapidily and increased the cutting forces, especially radial force. The tool was worn by the abrasive action. Flank Weat of $Al_2O_3-TiC$ ceramic and WC tool become relatively large and CBN & $Al_2O_3$, ceramic tool had a long life among the tool materials tested. The tool fracture patterns were just like minor cutting wear, flank wear, crater wear, notch wear, chipping. Flank wear rate was accelerated by occurrence of chipping. During the proceeding of machining, it was possible to foresee the catastrophic fracture of tool by abrupt increase of radial force.

• 한국국방경영분석학회지
• /
• 제36권2호
• /
• pp.39-52
• /
• 2010

미 국방성은 플랫폼중심전의 상향식소요제기에서 네트워크중심전의 하향식소요제기로 변화하고 능력기반전력구조개발에 힘쓰고 있으며, 한국군도 다변화하는 안보위협과 전시작전권전환을 앞두고 능력기반전력구조로의 전환을 시도하고 있으나 통합능력의 개념과 개발방법이 부족한 상태이다. 따라서 이 연구는 능력기반전력구조 개발을 위해 상 하위 조직 전체의 능력과 현재의 전력운용관점과 미래의 전력개발관점을 동시에 포함하는 통합능력프레임워크를 제시한다.

• Bulletin of the Korean Chemical Society
• /
• 제31권9호
• /
• pp.2581-2587
• /
• 2010

Nitration of tyrosine and tryptophan residues is common in cells under nitrative stress. However, physiological consequences of protein nitration are not well characterized on a molecular level due to limited availability of the 3D structures of nitrated proteins. Molecular dynamics (MD) simulation can be an alternative tool to probe the structural perturbations induced by nitration. In this study we developed molecular mechanics parameters for 3-nitrotyrosine (NIY) and 6-nitrotryptophan (NIW) that are compatible with the AMBER-99 force field. Partial atomic charges were derived by using a multi-conformational restrained electrostatic potential (RESP) methodology that included the geometry optimized structures of both $\alpha$- and $\beta$-conformers of a capped tripeptide ACE-NIY-NME or ACE-NIW-NME. Force constants for bonds and angles were adopted from the generalized AMBER force field. Torsional force constants for the proper dihedral C-C-N-O and improper dihedral C-O-N-O of the nitro group in NIY were determined by fitting the torsional energy profiles obtained from quantum mechanical (QM) geometry optimization with those from molecular mechanical (MM) energy minimization. Force field parameters obtained for NIY were transferable to NIW so that they reproduced the QM torsional energy profiles of ACE-NIW-NME accurately. Moreover, the QM optimized structures of the tripeptides containing NIY and NIW were almost identical to the corresponding structures obtained from MM energy minimization, attesting the validity of the current parameter set. Molecular dynamics simulations of thioredoxin nitrated at the single tyrosine and tryptophan yielded well-behaved trajectories suggesting that the parameters are suitable for molecular dynamics simulations of a nitrated protein.

• 대한치과보철학회지
• /
• 제9권1호
• /
• pp.63-68
• /
• 1969

The authors conducted the tests of the artificial masticatory forces on the everyday life foods divided into six groups of the vegetables, confectionaries, meats, fish, fruits and miscellaneous foods untreated or treated according to the taking of each foods by means of the human skull and electronic strain gauge for the pressure measurement. The results were as follows; 1. The masticatory forces of each foods were different. 2. The masticatory forces of the treated foods were lower than those of the untreated foods. 3. The masticatory forces needed to masticate the everyday life foods were considerably lower than the human maximum bite force. 4. It is reasonable to think the patients wearing well constructed full dentures feel no complications about the masticatory force for the mastication of everyday life foods. 5. The masticatory forces for the confectionaries were greater and more variable than the masticatory forces for the other foods.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.89-95
• /
• 2001

Ceramic tool has to equip with not only high toughness and strength but also low thermal expansion and good thermal conductivity which leads to the high thermal shock resistance. These characteristics make it have longer tool life under thermal stress condition. In this study, commercial Si$_3$N$_4$ceramic cutting tool and home-made SiC based ceramic cutting tools which have different sintering time and chemical composition are tested under various cutting speed and the feed rate increase, the cutting force and the flank wear growth ratio increase, too. The performance of home-made SiC based ceramic cutting tool shows the possibility to be a new ceramic tool.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.593-598
• /
• 2003

Ceramic plates containing many micro-holes are used in diverse applications such as MCP (Microchannel Plate). catalytic converters, filters, electrical insulators in integrated circuits, and so on. One of the efficient methods for machining many holes in ceramic plates is wet drilling of ceramic green bodies followed by sintering them. Since the strength of ceramic green bodies is much lower than the strength of sintered ceramic plate, ceramic green bodies can be drilled with high feed rate. The axial force during micro-drilling of ceramic green bodies increases rapidly at high feed rate, which induces the crack in workpiece. Therefore, the tool lift of micro-drill with respect to feed rate may be determined by the predicting increase of axial force. In this work, the axial force during micro-drilling was calculated using the chip flow model on the micro-drill tip. from which the tool life of diamond abrasive micro-drill during micro-drilling of ceramic green bodies was calculated.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.155-160
• /
• 2001

In the use of glass fiber reinforced plastics(GFRP) it is often necessary to cut the components, but the cutting of GFRP is often made difficult by the delamination of the compositions and short tool life. Experimental investigation was conducted to evaluate the chip formation of the glass fiber reinforced plastics during orthogonal cutting. The chip formation process, cutting force, and thrust force were studied. The chip formation processes were studied through the use of quick-stop device. Chip-tool contact areas were obtained with the use of the quick-stop device, and observed using optical microscopy after polishing. Cutting force and thrust force were measured through the use of the tool dynamometer.