• 전기화학회지
• /
• 제14권2호
• /
• pp.92-97
• /
• 2011

In this study we have investigated the Li-ion coordination, thermal behavior and electrochemical stability of N-butyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide ($Py_{14}TFSI$) with lithium bis(trifluoromethanesulfony)imide (LiTFSI) doping intended for use as electrolytes for lithium batteries. The ionic conductivity is reduced and glass transition temperature ($T_g$) increases with LiTFSI doping concentration. Also, the electrochemical stability increases with LiTFSI doping. A high LiTFSI doping could enhance the electrochemical stability of electrolytes for lithium batteries, whereas the decrease in the ionic conductivity limits the capacity of the battery.

• 한국전기전자재료학회논문지
• /
• 제21권3호
• /
• pp.249-254
• /
• 2008

Ag doping effect on $Li[Ni_{0.2}Li_{0.2}Mn_{0.6}]O_2$ cathode material was studied. Specially, we focused on rate performance of Ag doped samples. The $Li[Ni_{0.2}Li_{0.2}Mn_{0.6}]O_2$ powder was prepared by simple combustion method and the Ag was doped using $AgNO_3$ during gelation process. Based on X-ray diffraction analysis, there was no structural change by Ag doping, but the 'metallic' form of Ag was included in the doped powder. Both bare and Ag 1 wt.% doped sample showed similar discharge capacity of 242 mAh/g at 0.2C rate. However, as the increase of charge-discharge rate to 3C, Ag 1 wt.% doped sample showed higher discharge capacity (172 mAh/g) and better cyclic performance than those of bare sample. The discharge capacity of Ag 5 wt.% doped sample was relatively low at all rate condition. However it displayed better rate performance than other samples.

• Journal of Electrochemical Science and Technology
• /
• 제12권4호
• /
• pp.377-386
• /
• 2021

The Li-rich oxides are promising cathode materials due to their high energy density. However, characteristics such as low rate capability, unstable cyclic performance, and rapid capacity fading during cycling prevent their commercialization. These characteristics are mainly attributed to the phase instability of the host structure and undesirable side reactions at the cathode/electrolyte interface. To suppress the phase transition during cycling and interfacial side reactions with the reactive electrolyte, K (potassium) doping and Nb oxide coating were simultaneously introduced to a Li-rich oxide (Li_1.2Ni_0.13Co_0.13Mn_0.54O₂). The capacity and rate capability of the Li-rich oxide were significantly enhanced by K doping. Considering the X-ray diffraction (XRD) analysis, the interslab thickness of LiO₂ increased and cation mixing decreased due to K doping, which facilitated Li migration during cycling and resulted in enhanced capacity and rate capability. The K-doped Li-rich oxide also exhibited considerably improved cyclic performance, probably because the large K⁺ ions disturb the migration of the transition metals causing the phase transition and act as a pillar stabilizing the host structure during cycling. The Nb oxide coating also considerably enhanced the capacity and rate capability of the samples, indicating that the undesirable interfacial layer formed from the side reaction was a major resistance factor that reduced the capacity of the cathode. This result confirms that the introduction of K doping and Nb oxide coating is an effective approach to enhance the electrochemical performance of Li-rich oxides.

• 한국재료학회지
• /
• 제29권12호
• /
• pp.764-773
• /
• 2019

The gas response characteristic toward C₂H₅OH has been demonstrated in terms of copper-vacancy concentration, hole density, and microstructural factors for undoped/Li(I)-doped CuO thin films prepared by sol-gel method. For the films, both concentrations of intrinsic copper vacancies and electronic holes decrease with increasing calcination temperature from 400 to 500 to 600 ℃. Li(I) doping into CuO leads to the reduction of copper-vacancy concentration and the enhancement of hole density. The increase of calcination temperature or Li(I) doping concentration in the film increases both optical band gap energy and Cu2p binding energy, which are characterized by UV-vis-NIR and X-ray photoelectron spectroscopy, respectively. The overall hole density of the film is determined by the offset effect of intrinsic and extrinsic hole densities, which depend on the calcination temperature and the Li(I) doping amount, respectively. The apparent resistance of the film is determined by the concentration of the structural defects such as copper vacancies, Li(I) dopants, and grain boundaries, as well as by the hole density. As a result, it is found that the gas response value of the film sensor is directly proportional to the apparent sensor resistance.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.31.1-31.1
• /
• 2011

$Li_4Ti_5O_{12}$ is emerging as a promising material with its good structure stability and little volume change during the electrochemical reaction. However, its electrochemical performance is significantly limited by low electronic or ionic conductivity. In addition, high tap density is needed forim proving its volumetric energy density and commercialization. To enhance these properties, the spherical-like $Li_4Ti_5O_{12}$ particles were synthesized and carried out doping with yttrium. Prepared Y-doped $Li_4Ti_5O_{12}$ as a anode material showed great capacity retention rate of 92% (5C/0.2C), compared with no dope done. Consequently, it was found that Y doping into $Li_4Ti_5O_{12}$ matrix reduces the polarization and resistance on SEI layer during the electrochemical reaction.

• 한국수소및신에너지학회논문집
• /
• 제16권2호
• /
• pp.136-141
• /
• 2005

Li-doped NiO was synthesized by molten salt method. $LiNO_3$-LiOH flux was used as a source for Li doping. $NiCl_2$ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5:1 to 30:1 during the synthetic procedure and the Li doping amount of synthesized materials were found between 0.086-0.190 as a Li ion to Ni ion ratio. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies, however the lattice parameter decreased from 0.41769nm in pure NiO to 0.41271nm as Li doping amount increased. Hydrogen gas sensors were fabricated using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs $H_2$ concentration was checked up to 4% of $H_2$ in air (as higher concentrations above 4.65% are explosive in air) using Li doped NiO of Li ion/Ni ion=0.111 as the sensor material. The response time T90 and the recovery time RT90 were less than 25 sec. There was minimum interference of other gases and hence $H_2$ gas can easily be detected.

• Bulletin of the Korean Chemical Society
• /
• 제32권1호
• /
• pp.191-195
• /
• 2011

This study reports the root cause of the improved rate performance of $LiFePO_4$ after Cr doping. By measuring the chemical diffusion coefficient of lithium ($D_{Li}$) using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), the correlation between the electrochemical performance of $LiFePO_4$ and Li diffusion is acquired. The diffusion constants for $LiFePO_4$/C and $LiFe_{0.97}Cr_{0.03}PO_4$/C measured from CV are $2.48{\times}10^{-15}$ and $4.02{\times}10^{-15}cm^2s^{-1}$, respectively, indicating significant increases in diffusivity after the modification. The difference in diffusivity is also confirmed by EIS and the $D_{Li}$ values obtained as a function of the lithium content in the cathode. These results suggest that Cr doping facilitates Li ion diffusion during the charge-discharge cycles. The low diffusivity of the $LiFePO_4$/C leads to the considerable capacity decline at high discharge rates, while high diffusivity of the $LiFe_{0.97}Cr_{0.03}PO_4$/C maintains the initial capacity, even at high C-rates.

• 한국결정성장학회지
• /
• 제18권6호
• /
• pp.248-252
• /
• 2008

전기전도성이 우수하면서 입자 크기가 작은 $LiFePO_4$ 분말을 얻기 위해서, 이종원소(Cr+B 또는 Cr+Al) 도핑이 $LiFePO_4$의 전기전도도에 미치는 영향과 열처리 조건이 입자 크기에 미치는 영향에 대해서 조사하였다. 조성이 $LiFe_{0.965}Cr_{0.03}B_{0.005}PO_4$ and $LiFe_{0.065}Cr_{0.03}Al_{0.005}PO_4$인 두 종류의 분말을 기계화학적 밀링법으로 혼합 후 $675{\sim}759^{\circ}C$에서 $5{\sim}10$시간 열처리하여 합성하였다. 이종원소 도핑은 입자성장을 촉진하였고 전기전도도를 높이는 효과가 있었다. $LiFe_{0.065}Cr_{0.03}Al_{0.005}PO_4$의 전기전도도는 $1{\times}10^{-8}S/cm$로 도핑하지 않은 것의 $5{\times}10^{-10}S/cm$보다 높았다.

• The Korean Journal of Ceramics
• /
• 제3권2호
• /
• pp.110-115
• /
• 1997

Li-doped ZnO films were prepared on Corning 1737 glass substrate by an rf magnetron sputtering technique using ZnO targets with various $Li_2CO_3$ contents ranging from 0 to 10 mol%. The effects of Li doping on the crystallinity and electrical properties of ZnO films were studied for their SAW filter applications. The film resistivity largely increased without suppressing the c-axis orientation and crystallinity with a small addition of Li. Heat treatment of the film at 40$0^{\circ}C$ induced that the film resistivity, c-axis orientation and crystallinity slightly increased. However, heat treatment of the film at 50$0^{\circ}C$ resulted in much lower resistivity than that of as-deposited film due to the increase of electron concentration caused by the evaporationof Li atoms from the ZnO film. Large addition of Li into the ZnO film rather diminished the film resistivity and suppressed the c-axis growth. It was concluded that a small doping of Li into the ZnO film and heat treatment at 40$0^{\circ}C$ caused the film resistivity to be high enough for SAW filter applications without suppression of the c-axis orientation and crystallinity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.55-55
• /
• 2008

이차전지의 음극 중 $LiC_6$는 높은 용량을 보이나 완충하는 프로세스 동안에 금속리튬에 가까운 potential을 갖게 되어 조작에 어려움이 있다. 이러한 대용물질로서 $Li_4Ti_5O_{12}$ spinel은 가볍고 높은 에너지 밀도를 가지고 있고 낮은 전압영역이 가능하여 이차전지의 음극 물질로서 유용하다. 그러나 $Li_4Ti_5O_{12}$ 물질 자체가 insulation이며, 고상합성법을 사용하게 되면 좋은 특성을 나타내기가 어렵다. 이번 실험에서는 고상합성을 통하여 $Ba^{2+}$와 $Sr^{2+}$이온을doping한 후 전기화학적 특성이 어떻게 향상되었는가를 연구하였다. Ba와 Sr을 첨가한 $Li_4Ti_5O_{12}$는 첨가하지 않은 물질에 비하여 보다 안정적인 평탄구역을 갖게 되었으며 방전용량이 $40mAhg^{-1}$의 향상을 가져왔다. 또한 Li half cell에서 100cycle 진행하는 동안 보다 안정적인 전극구조를 유지하였다.