• Journal of Korean Society of Transportation
• /
• v.17 no.5
• /
• pp.137-149
• /
• 1999

For decades, many traffic flow studies on the analysis and determination of level of service (LOS) for the weaving sections have been made to Provide several regression equations. Weaving and non-weaving speeds were dependent variables for the equations, with independent variables being weaving length, number of lanes, and weaving ratios. One of the difficulties in developing the equations was that the weaving areas were rare in Korea, so the statistical analyses for calibrating the equation parameter could not be performed in a desirable manner. In this regard, a new and stochastic methodology for predicting the weaving and non-weaving speeds within the weaving sections was required. In this study the following design variables were developed; influence area of the weaving section. headway distribution within the weaving section, maximum weaving volume of the weaving section, length of the ideal weaving section, and speed estimations for the weaving and non-weaving flows. The evaluation of the new model was made comparing the delay in the weaving section with the one in the freeway basic section.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.66-80
• /
• 1997

This paper describes a newly developed arc-sensing algorithm of seam-tracking for FCA W (flux-cored arc welding) horizontal fillet welding. In this algorithm, arc current and the Weighted-Are-Current (WAC) are used to adjust the position of a weld torch in directions of bead throat and weaving, respectively. The WAC, which is newly devised in this study, means that arc current in the vicinity of weaving end is more emphasized than that in the center of weaving. The reason of this is because there usually exists much noise in the center of weaving due to abrupt change of arc length in case some empty gaps exist in a fillet joint Variance analysis was performed in order to check the effect of weld parameters on arc current and the WAC. As a result, the relationships between tip-to-workpiece distance and arc current, and between weaving offset and the WAC were established.To check "the validity of the algorithm, seam-tracking experiments were performed ;mder various welding condition. The result of experiments showed a satisfactory tracking performance in the presence of empty gaps in a horizontal fillet joint.et joint.

• Journal of Korean Society of Transportation
• /
• v.30 no.4
• /
• pp.21-32
• /
• 2012

Exclusive bus lane (EBL) is typically located in the roadway median, and is accessed by weaving across the GPLs(general purpose lanes) before entering from the left lane of the GPLs. To maximize the potential for successful EBL operations, a critical design issue that requires special attention is the length of bus weaving section before entering EBL. The process of developing guidelines for the length of bus weaving section can be supported by a sensitivity analysis of performance measure (safety) with respect to the bus weaving distance. However, field data are difficult to obtain due to inherent complexity in creating performance measure (safety) samples under various interesting flows and bus weaving distance that are keys to research success. In this paper, VISSIM simulation is applied to simulate the operation of roadway weaving areas with EBL, and based on vehicle trajectory data from microscopic traffic simulation models, the Surrogate Safety Assessment Model (SSAM) computes the number of surrogate conflicts (or degree of safety) with respect to the bus weaving distance. Then, a multiple linear regression (MLR) model using safety data (number of surrogate conflicts) is developed. Finally, guidelines for bus weaving distance are established based on the developed MLR. Developed guidelines explicitly indicate that a longer bus weaving distance is required to maintain desired safety as weaving volume increases.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.60 no.2
• /
• pp.186-193
• /
• 2024

Most fishing nets used in fish cage aquaculture are made of synthetic fibers such as polyamide (PA) and polyethylene (PE). Therefore, it is challenging to maintain the internal volume of the fish cage due to biofouling, which can increase the load on the cage or reduce dissolved oxygen levels by impeding smooth current flow. To address this issue, research has been conducted to replace conventional synthetic fiber cage nets with brass nets, demonstrating certain benefits such as improved productivity and ease of fish cage management. However, given the need for a more thorough examination of brass fishing net weaving technology and performance, this study assessed the optimal weaving method for brass fishing nets to be used in fish cages. Additionally, it provided essential data for the practical application of brass fishing nets by evaluating their weight, tensile strength, elongation, fatigue resistance, and wear resistance. The study concluded that weaving brass fishing nets using the chain link method ensures durability, ease of installation, and compact storage in a scroll-like form. Moreover, due to their superior fatigue and wear resistance properties, brass nets can offer increased utility if appropriate net diameter and length are selected to compensate for their higher weight per unit area and relatively higher cost compared to existing fiber fishing nets.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.1
• /
• pp.23-30
• /
• 2005

The air-jet loom represents a major step in the development of shutterless weaving due to its ability to weave a wide range of yarns at high speeds. The air-jet weaving involves inserting a pre-measured length of yarn through the wraps, which is shed by means of compressed air. The analysis of air flow characteristic of the main nozzle and acceleration tube is required for improving the loom performance. In this paper, we examined the effects of the main nozzle with different acceleration tubes as well as diameters. Also, we compared the performance of a straight-type tube with a Laval-type tube and the effect of installing a suction hole on the acceleration tube.

• Journal of ILASS-Korea
• /
• v.8 no.2
• /
• pp.16-23
• /
• 2003

The Air-jet loom represents a major step in the development of shutterless weaving due to its ability to weave a wide range of yarns at high speeds. The Air-jet weaving involvers, inserting a pre-measured length of yam through the wrap, is sheds by meads of compressed air. The analysis of air flow characteristic of the main nozzle and acceleration tube is required for the loom performance. h this paper We examined the effect of the main nozzle with different acceleration tubes as well as diameters. And also, we compared the performance of straight type tube with laval type tube and of according to be suction hole on the acceleration tube, respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.94.1-94
• /
• 2001

Arc sensor gives important groove information during welding. Automatic seam tracking control system with arc sensor has significant characteristics such that bead formation is given as decentralization of penetration and formation of concave bead profile and that a turning point of transverse weaving with constant arc length control is decided whether or not torch height reaches to a specified setting level. Furthermore, the rotating action of the arc prevents hanging of weld bead and forms flat bead surface under high speed welding condition. The variation of groove and deposition area can be detected from the trace of weaving. The area and width of weaving trace has close correlation with the area of groove and deposition. In this paper, main object of this system is to realize an adaptive microprocessor based controller ...

• Journal of Welding and Joining
• /
• v.16 no.4
• /
• pp.125-135
• /
• 1998

The shielded metal arc welding (SMAW) by AC power source was performed to evaluate the arc stability by arc monitoring and analysing. In this study, the arc stability index was evaluated quantitatively by using he coefficient of resistance variation for welding time. This coefficient was obtained for the long time (20sec.) by analysing the waveforms of welding current, voltage and resistance. The coefficient was applied to indicate numerically the variation level of arc length and the degree of arc extinction. Using the coefficient of resistance variation in practical welding, the arc stability of the high titanium oxide electrode (KS E4313) turned out to be better than that of the low hydrogen electrode (KS E4316). In evaluating the skill level of welders by the coefficient, the horizontal fillet weaving welding became clear to be very discriminating because the higher level welder could weave in keeping constant arc length, but the lower level welder showed the characteristics of weaving with the unstable arc length. And it was confirmed that the welding defects as blow holes was formed when the arc stability index were high.

• Fibers and Polymers
• /
• v.6 no.4
• /
• pp.306-312
• /
• 2005

This work looks into the behaviour of the twill weave woven fabrics during relaxation (when the weaving tension is released). Ten, 50-metre rolls of twill weave woven fabrics were produced. The fabrics were marked in a rectangular form at the weaving loom. After 48 hours of relaxation, the new shapes and sizes were recorded. The shapes of almost all of the samples were changed to parallelogram, even though they differed in size. The work showed that the manner of fabric deformation during relaxation depends upon the fabric structure. It indicates that contraction due to relaxation of the twill weave causes the woven fabric to skew. in the direction of the twill. The quantity of the skewness is related to the float length and the twill type. Fabrics with longer float length have higher skewness.

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.23-25
• /
• 2001