• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.283-292
• /
• 1996

This study was performed to determine the physical properties of rice hull and straw which could be used for an optimum design and operation of the handling facilities for these rice crop by-products. The properties measured were kinetic friction coefficient , bulk density, and dynamic and static angle of repose. Rice hulls with moisture content of 13% and 21% were used throughout the test while rice straws of 10% and 16% moisture were chopped into 10mm length and used for the test. Friction coefficient was calculated from the horizontal traction forces measurement when a container holding the mass of rice hull and straw was pulled over mild steel. PVC, stainless steel, and galvanized steel surface by a universal testing machine. Bulk density was measured by an apparatus consisting of filling fundel and a receiving vessel. Dynamic angle of repose which is the angle at which the material will stand when piled was calculated from the photos of bulk samples after they were flowed by gravity and accumulated on a circular surface. Static angle of repose which is the angle between the horizontal and the sloping side of the material left in the container when discharging was also measured in the similar way. Results and conclusions from this study are summarized as follows . 1. Kinetic friction coefficient of both rice hull and straw were in the range of 0.26 -0.52 and increased with the moisture content. The magnitude of friction increased in the order of galvanized steel, stainless steel, PVC ,and mild steel. 2. Bulk densities of rice hull decreased while those of rice straw increased with moisture content increase . Average bulk densities of rice hull and straw were 96.8 and 74.7kg/㎥, respectively. 3. Average dynamic angle of repose for rice straw was 32.6$^{\circ}$ and those for 13% and 21% moisture rice hull were 38.9$^{\circ}$ and 44.9$^{\circ}$ , respectively. 4. Static angles of repose for both rice hull and straw showed increase with the moisture content. The values were 75.2\ulcorner and 80.2$^{\circ}$ for 13% and 21% moisture rice hull, respectively. Rice straws having 10% and 16% moisture content showed 87.3% and 89.2$^{\circ}$ static angle of repose, respectively.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.56 no.3
• /
• pp.219-225
• /
• 2011

The physicochemical properties of rice endosperm from five rice varieties and effects of milling on baking bread properties of rice flour were investigated. Five rice varieties exhibited different level of amylose content. The ratio of longer amylopectin chain length to the distribution of endosperm starches was the highest in Goami3. According to the RVA measurement of rice flours, the pasting temperatures of Seolgaengbyeo and Goamibyeo were lower than those of the other rice varieties. There were differences in the changes of swelling power of rice flour under increasing temperature. Each rice flour sample for bread-making was processed into two different particle size by using an air-classification mill, and significant differences were observed among cultivars in the average particle size and damaged starch content of rice flours. Rice flour of Seolgaengbyeo with fine particle size showed the highest value in specific volume after baking.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.2
• /
• pp.99-111
• /
• 2003

The fundamental studies on the productivity improvement of the purse seine fishery are presented in this paper. The experiment on net shooting and hauling was carried out in the near sea of Jeju Island (33$^{\circ}$37.8' N, 126$^{\circ}$31.1' E) by using the Cheju national university training ship (A-Ra, 990tons) which was constructed for the one boat system operation of purse seine. The corkline and leadline of the purse seine used for the experiment were 829.1m and 995.7m in length, respectively. Micro data recorder system, net sonde, and tensiometer were used to measure the depth of leadline and the tension of purse seine. Based on the measurement data, the motion and tension of purse seine at the time of shooting, hauling, and pursing were characterized. The experimental results are summarized as follows ; 1. The shooting and hauling of net were found to be possible in the one boat system experimental operation. 2. At the time of purse seine shooting, the relationship between the depth (Dp) of leadline and elapsed time (Et) was found to be Dp=7.58Et-6.48. 3. At the time of pursing, the relationship between the depth (Dp) of leadline and elapsed time (Et) was found to be Dp=-0.8Et$^2$＋7.42Et＋92.04. 4. At the time of pursing, the tension (metric tons) of purse seine attained its maximum value (14.7tons) when the elapsed time is 8 minutes. The relationship with the elapsed time was found to be T=-0.13Et$^2$＋3.23Et-5.72.

• Journal of fish pathology
• /
• v.28 no.1
• /
• pp.37-42
• /
• 2015

In the present study, we performed a dipping of olive flounder (average length and weight: $20{\pm}2.0cm$, $70{\pm}5.0g$) for a period of three hours a day, over two days, in a melted complex of oxytetracycline (OTC) and neomycin (N), by dissolving 25-10 ppm or 50-20 ppm in water. Subsequently, the remaining antibiotic density in muscle tissue collected from olive flounder was investigated, 1, 5, 14 and 40 days after discontinuation of the medication. 5 fish were used from each group. The standard graph drawn from the results of diluting two standard solutions of OTC and N based on various density levels, showed a relatively straight line with an $R^2$ of 0.9999 and 0.9952, respectively. The recovery rate of OTC was shown to be 90-93% and N, 88-95%. Upon measurement of the remaining antibiotic density in the test group that had been exposed to 25-10 ppm of the complex of OTC and N, $0.97{\pm}0.084{\mu}g/ml$ of OTC and $0.118{\pm}0.079{\mu}g/ml$ N were detected on 1 day of the test. No antibiotic density was detected after day 5 of the test. Regarding the test group that were exposed to 50-20 ppm of the complex of OTC and N, $1.324{\pm}0.062{\mu}g/ml$ of OTC and $0.788{\pm}0.05{\mu}g/ml$ N were detected on day 1 of the test, and no antibiotic density was detected after day 5 of the test.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.4
• /
• pp.162-168
• /
• 2014

The OFDM system have been widely studied for the purpose of increasing data rate with more reliable communications in underwater channel environments. And it is possible only when the sub-carrier's bandwidth is smaller than the coherence bandwidth of channel in the underwater OFDM communication system. However, the size of the FFT for the OFDM system will be increased because the coherence bandwidth is as small as several tens of Hz in real underwater channel environments. Also, It is necessary to add a CP having a length longer than the rms delay spread of a channel. So the complexity of the system is increased and the data efficiency is reduced. Therefore, in this paper, we have studied the increase of the coherence bandwidth by adapting the beamforming technologies. To do this, we have collected data from real underwater channel environments and analyzed the coherence bandwidth when adapting the beamforming technologies. Analyzing the experimental data show that the coherence bandwidth by the beamforming technologies in underwater channel environments was greatly increased compared to that of a single sensor.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.27-36
• /
• 2004

The corrosion rate measurement procedure for the permanent ground anchors using polarization resistance measurements and electrochemical impedance spectroscopy is presented in this paper. The polarization resistance measurements were used to determine the correlation between corrosion rate in the steel and soil characteristics. The electrochemical impedance spectroscopy was used to predict the time dependent corrosion reaction and evaluate the different type of coating systems and the effect of cement grouting on the corrosion attack under various conditions. The results indicate that a low pH soil is a good indicator of a corrosive soil. The low pH soil condition (<5) in both clay and sand has a significant effect on the corrosion reaction of steel members in permanent found anchors. In the case of neutral and alkaline conditions beyond pH 6 in clay and sand, no consistent acceleration of corrosion was measured and the corrosion rate was constant regardless of variations of soil pH levels. Laboratory test data for porcelain clay indicate that the change of soil pH level has a small influence on the corrosion reaction in the steel member. The use of cement footing in the bonded length is sufficient to decrease the corrosion rate to a level close to 0.003∼0.01mm/y at the end of the given period. With epoxy and fusion bonded epoxy coating, the steel specimens remained unaffected and retained the original condition. It is suggested that epoxy and fusion bonded epoxy coating can provide effective protection against corrosion for a long time even in aggressive environment.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.1
• /
• pp.57-66
• /
• 2012

The purpose of this study was to evaluate the relation between intentionally induced internal stress and cyclic fatigue failure of ProTaper Universal. ProTaper Universal (Dentsply Maillefer) S1, S2, F1, F2, F3, F4 and F5 (25 mm length) were used in this study. To give the internal stress, the ProTaper Universal were put into the .02 taper Endo-Training-Bloc (Dentsply Maillefer) until auto-stop by torque controlled motor. The rotation speed was 300 rpm and torque value was 1.0 Ncm. ProTaper Universal were grouped by the induced number of internal stress and randomly distributed among one control group and three experimental groups (n=10). The four groups were Stress 0 (control), Stress 1, Stress 2 and Stress 3. These instruments were rotated until separation. For cyclic fatigue measurement, inclined plane was used and time for separation was recorded. It was statistically analyzed using two-way ANOVA and Duncan post-hoc test at 95% confidential level. In all ProTaper Universal, there was statistically significant decrease on time for separation in Stress 3. In F2 and F3, there were statistically significant difference between control group and all experimental groups. And in F4 and F5, Stress 2 and 3 groups showed significantly lower cyclic fatigue resistance from Stress 0 group. In the limitation of this study, cyclic fatigue failure of ProTaper Universal is influenced by accumulated internal stress.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.23 no.4
• /
• pp.327-336
• /
• 2007

Purpose This study was planned to compare and evaluate the stability of implant using $Osstell^{TM}$ and Osstell $Mentor^{TM}$. Material and methods Artificial bone and RBM(resorbable blasting media) surface blasted implants(Osstem US II, SS II implants - diameter: 4mm, length: 13mm) were used. To measure the stability of installed implants, $Osstell^{TM}$ and Osstell $Mentor^{TM}$ were used. In the first experiment, five implants were installed in D1(external type implants) and D3(internal type implants). In the second experiment, 4 internal type implants were divided in two groups and installed in D1 artificial bone with different depth. In the third experiment, two external implants were installed in D1 and D3 artificial bone each and two internal implants were installed in D1 and D3 artificial bone. In all groups, their stability were measured by $Osstell^{TM}$ and Osstell $Mentor^{TM}$. Results In all groups, $Osstell^{TM}$ and Osstell $Mentor^{TM}$ both showed reliable measurement values. The value difference between $Osstell^{TM}$ and Osstell $Mentor^{TM}$ was observed but the difference was small and clinically acceptable. Conclusion These results suggest that the use of Osstell $Mentor^{TM}$ has clinical relevance in the assessment of implant stability.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.1
• /
• pp.65-74
• /
• 2018

The aim of this study was to obtain the traceability of the software used to analyze lateral cephalometry and to calculate the uncertainty of the measurements. Furthermore, this study aimed to provide a basis for obtaining standard references for measurement values for orthodontic treatment in children. Cephalometric data were collected from 100 children diagnosed with class I malocclusion between the ages 6 to 13 years who visited the pediatric dentist at Seoul National University Dental Hospital. To ensure traceability, a phantom device was created. Correction values were calculated by measuring the length and angle of the phantom device using the software. Type A uncertainty was calculated by obtaining the standard deviation of cephalometric measurements of 100 persons and the standard error of repeated measurements. Determination of the type B uncertainty was induced by minimum resolution and the position of the head. Using these, the combined standard uncertainty was obtained and the expanded uncertainty was calculated. The results of this study confirm that the currently used software has high accuracy and reliability. Furthermore, the uncertainty of orthodontic measurements in Korean children aged 6 to 13 years was calculated, and distribution range for class I malocclusion with 95% confidence interval was suggested.